Keysight U1211A User manual

Keysight U1211A,
U1212A, and U1213A
Clamp Meter
Quick Start
Guide

Contacting Keysight
www.keysight.com/find/assist
(worldwide contact information for
repair and service)
Safety and EMC Information
The U1211A, U1212A, and U1213A
is safety-certified in compliance
with EN/IEC 61010-1, ANSI/UL
61010-1, and CAN/CSA-C22.2
No.61010-1-04.
EMC is designed in compliance
with IEC61326-1/EN61326-1,
CISPR 11/EN 55011 Group 1 class
A, ICES-001, AS/NZS CISPR11.
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in damage to the product or
loss of important data. Do not
proceed beyond a CAUTION notice
until the indicated conditions are
fully understood and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in personal injury or
death. Do not proceed beyond a
WARNING notice until the
indicated conditions are fully
understood and met.
Safety symbols
Direct current (DC)
Alternating current (AC)
Earth (ground) terminal
Application around and
removal from HAZARDOUS
LIVE conductors is
permitted
Equipment protected
throughout by double
insulation or reinforced
insulation
Caution, risk of electric
shock
Caution, risk of danger
(refer to this manual for
specific Warning or Caution
information)
Category III 1000 V
overvoltage protection
Category IV 600 V
overvoltage protection
CAT III
1000 V
CAT IV
600 V
2 Keysight U1211A, U1212A, and U1213A Quick Start Guide
For further safety information details, refer to the
Keysight U1211A, U1212A, and U1213A Clamp Meter User’s Guide.

Keysight U1211A, U1212A, and U1213A Quick Start Guide 3
Table of Contents
Knowing Your Clamp Meter . . . . . . . . . . . . . . . 6
Functions and Features . . . . . . . . . . . . . . . . . . . 7
Rotary switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Function buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Annunciator Display . . . . . . . . . . . . . . . . . . . . . 9
Input Terminals . . . . . . . . . . . . . . . . . . . . . . . . 11
Performing Current Measurement . . . . . . . . . 13
Performing Voltage Measurement . . . . . . . . . 16
Performing Resistance Measurement and
Continuity Test . . . . . . . . . . . . . . . . . . . . . . . 18
Performing Diode Measurement . . . . . . . . . . . 20
Performing Capacitance Measurement . . . . . 22
Performing Temperature Measurement . . . . . 24
Replacing the Battery . . . . . . . . . . . . . . . . . . . 26
Regulatory Markings . . . . . . . . . . . . . . . . . . . . 28

4 Keysight U1211A, U1212A, and U1213A Quick Start Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Keysight U1211A, U1212A, and U1213A Quick Start Guide 5
The following items are included with your clamp
meter:
4Standard test leads with 4 mm probes
4Soft carrying case
4Quick Start Guide
4Certificate of Calibration
If any item is missing or damaged, contact your
nearest Keysight Sales Office.
For more detailed information, please refer to the
Keysight U1211A, U1212A, and U1213A Clamp
Meter User’s and Service Guide on Keysight
Website: www.keysight.com/find/handheld-tools
U1211A U1212A U1213A

6 Keysight U1211A, U1212A, and U1213A Quick Start Guide
Knowing Your Clamp Meter
Clamp jaw
Handle
Hand guard
Annunciator
Jaw
markings
Rotary
switch
Function
buttons
Hold/
Max Min
button
Red input
terminal
Black input
terminal
Front
panel

Keysight U1211A, U1212A, and U1213A Quick Start Guide 7
Functions and Features
Rotary switch
Function buttons
Measurements
and power off
functions
Actions Steps
Freeze measured value Press Hold/Max Min
– Record maximum, minimum, and
calculate true average
– Toggle between maximum, average,
and minimum
–PressHold/Max Min > 1 second
–PressHold/Max Min again
Toggle measurement type Press Shift/Peak
Toggle peak hold test Press Shift/Peak > 1 second
Enable frequency or duty cycle[a] on
secondary display
Press Hz/

8 Keysight U1211A, U1212A, and U1213A Quick Start Guide
[a] Duty cycle % function is only available for U1213A.
Turn on backlight Press Hz/ > 1 second
Offset measured value Press ΔNull
Change measuring range manually Press Range/Auto
Turn on auto range Press Range/Auto > 1 second
Actions Steps

Keysight U1211A, U1212A, and U1213A Quick Start Guide 9
Annunciator Display
No. Annunciator Status
1 AUTO Indicates auto ranging
2Zeroingmode
3 DH Data hold
4 MAX AVG MIN Dynamic recording mode on present reading.
MAX: maximum reading, MIN: minimum reading,
AVG: average reading
5 Direct current or voltage
6 Alternating current or voltage
7 Capacitor measurement unit
8 Audible continuity indicator
9 A Current measurement unit
10 Low battery indicator when battery voltage drops
below 6.0 V
11 V Voltage measurement unit

10 Keysight U1211A, U1212A, and U1213A Quick Start Guide
12 M k ΩResistance measurement unit and range
13 Diode measurement indicator
14 % Duty cycle (for U1213A only)
15 kHz Frequency measurement unit
16 Secondary display (for frequency and duty cycle
measurement and temperature unit)
17 Analog bar-graph with scale indicator
18 Auto power off enabled
19 Negative polarity
20 Primary display
No. Annunciator Status