Keysight N9030B Installation and operation manual

Keysight Technologies
N9030B Signal Analyzer
Option 107
Audio Input and Digitizer
Upgrade Kit
Installation Note

Notices
© Copyright 2018 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9030-90111
Edition
Edition 2, October 2018
Supersedes none
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403

Installation Note N9030-90111 3
Option 107, Audio Input and Digitizer Upgrade Kit
Option 107, Audio Input and Digitizer Upgrade Kit
Products Affected: N9030B, PXA Signal Analyzer
Serial Numbers: All
Option 107
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
(X) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Timea:
a.To ensure that this newly installed option is functioning properly, the procedure that follows includes the
requirement of performing certain adjustments and performance verification tests. However, the completion of
these tests does not guarantee that the instrument meets all advertised specifications.
Software and test equipment is required for making adjustments and for performance verification testing.
Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
While Keysight does recommend that a full calibration be performed after the installation of this upgrade, the
end user must ultimately determine whether they want this service or not. If a full calibration is required,
arrangements regarding the level of calibration must be made between the end user and the calibration
provider.
1.0 Hours
0.0 Hours
0.5 Hours

4Installation Note N9030-90111
Option 107, Audio Input and Digitizer Upgrade Kit
Introduction
This kit provides all parts and instructions necessary to install Option 107, Audio Input and
Digitizer, into the Keysight N9030B.
1. This upgrade kit is not compatible with N9030B PXA signal analyzers with any
of the following options currently installed:
N9030B-B5X - 510 MHz Analysis Bandwidth
N9030B-BBA - I/Q Baseband Inputs
2. This upgrade kit installation requires that you re-install instrument software.
The latest revision of the PXA Signal Analyzer software may be downloaded
from
http:/www.keysight.com/find/xseries_software
The instrument software must be installed AFTER the hardware in the kit is
installed. Follow the procedure in this document for redeeming and installing
the option upgrade license key.
3. The option is licensed for one instrument model/serial number combination.
The license key will only install on the designated instrument.

Installation Note N9030-90111 5
Option 107, Audio Input and Digitizer Upgrade Kit
Installation Kit Parts List
Quantity Description Keysight Part Number
1 Screw, FLT-HD Torx T10 M3 x 0.5 (6 mm long) 0515-1227
1 Lock Washer, Internal tooth 2190-0068
1 Hex Nut 15/32-32 Interface Board 2950-0035
1 Coaxial Cable Assembly w/Toroids N9020-60344
1 Cover Plate, Audio N9030-00004
1 PCA, Audio Digitizer N9030-60047
1 Overlay, Audio Input N9030-80062
1 Installation Note this note
1 Option Upgrade Entitlement Certificate n/a

6Installation Note N9030-90111
Option 107, Audio Input and Digitizer Upgrade Kit
Tools Required
— T-10 Torx Driver
— T-20 Torx Driver
— 5/16-inch torque wrench
— 1/4-inch open end wrench
— 1/4-inch socket on 4 lb torque wrench
—scissorsorknife
—diagonalcutters
— USB storage device with > 2 GB free memory
Before you disassemble the instrument, turn the power switch to Standby, wait until the
instrument has completely shut down, and unplug the instrument. Failure to unplug the
instrument can result in personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.

Installation Note N9030-90111 7
Option 107, Audio Input and Digitizer Upgrade Kit
Installation Procedure
Instrument Cover Removal
1. Power down the instrument and wait for the standby light to come on. Disconnect the
instrument from ac power.
2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that
attach the strap handles (2) on each side of the instrument.
3. Remove the four key locks from the instrument four bottom feet.
4. Remove the four instrument bottom feet.
5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet
(4) in place.
6. Pull the instrument cover (5) off towards the rear of the instrument.
If the instrument is placed on its face during any of the following procedures, be sure to use a soft
surface or soft cloth to avoid damage to the front panel, keys, or input connector.
Make sure any adapters on the front panel are removed.

8Installation Note N9030-90111
Option 107, Audio Input and Digitizer Upgrade Kit
Figure 1 Instrument Outer Case Removal

Installation Note N9030-90111 9
Option 107, Audio Input and Digitizer Upgrade Kit
Top Brace Removal
1. Refer to Figure 2. To remove the top brace (1), use the T-10 driver to remove the twelve
panhead screws (3) (0515-0372) attaching the top brace to the chassis. Remove the twelve
screws (fourteen screws with Option B1X) (4) (0515-1946) attaching the top brace to the
boards.
Figure 2 Top Brace Removal

10 Installation Note N9030-90111
Option 107, Audio Input and Digitizer Upgrade Kit
Option 107 Hardware Installation
1. Refer to Figure 3. Locate and install the N9030-60047 Audio Digitizer PCA into slot 7.
Figure 3 Option 107 Audio Digitizer