Kichler Lighting 300318 User manual

INSTRUCTION MANUAL
Model#: 300318
Product images may vary slightly from actual product.
52" Bezel LED

KICHLER.COM

TABLE OF CONTENTS
SAFETY RULES …………………………………………………………………………....4
TOOLS REQUIRED …………………………..………………………………..………...5
PACKAGE CONTENTS ……………….....................……………………………....5
MOUNTING OPTIONS ………….................................................................6
HANGING THE MOTOR ASSEMBLY........................................………...7
ELECTRICAL CONNECTIONS …………................................................10
FINISHING THE MOTOR INSTALLATION.....………..........................11
INSTALLING THE BLADE HOLDER RING …….............................…12
ATTACHING THE FAN BLADES ….................................................……13
ATTACHING THE BLADES TO THE MOTOR ASSEMBLY ...……13
INSTALLING THE LIGHT PLATE …................................................…. 14
INSTALLING THE LIGHT KIT AND ACRYLIC SHADE…………..... 15
OPERATING INSTRUCTIONS…….……………………...........……………... 16
TROUBLESHOOTING …………………………..................………………………18
FCC INFORMATION ............…………………………………………………..........19
52" Bezel LED | 3

4 | KICHLER.COM
SAFETY RULES
READ AND SAVE THESE INSTRUCTIONS
CAUTIONCAUTION – RISK OF SHOCK – Disconnect Power at– RISK OF SHOCK – Disconnect Power at
the main circuit breaker panel or main fuse box beforethe main circuit breaker panel or main fuse box before
starting and during the installation.starting and during the installation.
WARNING:WARNING: This fixture is intended for installation inThis fixture is intended for installation in
accordance with the National Electrical Code (NEC) andaccordance with the National Electrical Code (NEC) and
all local code specifications. If you are not familiar withall local code specifications. If you are not familiar with
code requirements, installation by a certified electrician iscode requirements, installation by a certified electrician is
recommended.recommended.
WARING:WARING: To reduce the risk of fire or electric shock, useTo reduce the risk of fire or electric shock, use
only the control provided with the fan.only the control provided with the fan.
WARNING:WARNING: To reduce the risk of fire, electric shock, orTo reduce the risk of fire, electric shock, or
Personal Injury, mount directly to a structural framingPersonal Injury, mount directly to a structural framing
member or to an outlet box marked “Acceptable For Fanmember or to an outlet box marked “Acceptable For Fan
Support of up to 22.6kg(50 lbs)”. For outlet box mounting,Support of up to 22.6kg(50 lbs)”. For outlet box mounting,
use mounting screws provided with the outlet box.use mounting screws provided with the outlet box.
WARNING:WARNING: Do not operate reversing switch while fanDo not operate reversing switch while fan
blades are in motion. Fan must be turned off and bladesblades are in motion. Fan must be turned off and blades
stopped before reversing blade direction.stopped before reversing blade direction.
Avoid placing objects in the path of the blades.Avoid placing objects in the path of the blades.
To avoid personal injury or damage to the fan and otherTo avoid personal injury or damage to the fan and other
items, be cautions when working around or cleaning theitems, be cautions when working around or cleaning the
fan.fan.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Make sure the installation site you choose allows a
minimum clearance of 7 feet from the blades to the floor
and at least 30 inches from the ends of the blades to any
obstruction.
Do not use water or detergents when cleaning the fan or
fan blades. A dry dust cloth or lightly dampened cloth will
be suitable for most cleaning.
After making the electrical connections, spliced
conductors should be turned upward and pushed carefully
up into outlet box. The wires should spread apart with the
ground wire and white(common) wire to one side with the
black (load) wire to the other side of the outlet box.
Electrical diagrams are for reference only. Light kits that
are not packed with fan must be ETL Listed and marked
suitable for use with the model fan you are installing.
Switches must be ETL General Use Switches. Refer to the
instructions packaged with the light kits and switches for
proper assembly.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY. DO NOT
BEND THE BLADE BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER INSTALLATION.
DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

TOOLS REQUIRED
PACKAGE CONTENTS
Phillips screwdriver
Blade screwdriver
11 mm wrench
Step ladder
Wire cutters
Unpack your fan and check the contents . You should have the following items:
A. Mounting bracket
B. Ball / downrod assembly
C. Canopy
D. Canopy Hole Cover
E. Coupling Cover
F. Motor Body
G. Blade Holder Ring
H. Fan Blade (3)
I. Blade Holder (3)
J. Light Plate
K. Light Kit
L . Acrylic Shade
M. Remote Control Kit:
Remote Control (1)
Receiver (1)
Battery (1)
Wire Connectors (6)
Handset Control Holder (1)
N. Package hardware
1) Mounting hardware :
Wire Connector (3)
2)Blade attachment hardware :
Screws(9), Washer (9)
3.) Blade Holder attachment hardware:
Screw (6)
4.) Blade holder ring hardware:Screw (4)
A
K
G
IN
M
L
J
B
C
D
E
F
H
52" Bezel LED | 5

6 | KICHLER.COM
MOUNTING OPTIONS
If there is not an existing UL (cUL for Canadian Installation ) listed
mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the full weight of the fan (up to
50 lbs). Do not use plastic outlet boxes.
Figure 1, 2 and 3 are examples of dierent ways to mount the outlet
box.
NOTE:NOTE: If you are installing the ceiling fan on a sloped (vaulted) ceiling,
you may need a longer downrod to maintain proper clearance
between the tip of the blade and the ceiling. A minimum clearance of
12” is suggested for optimal operation.
NOTE:NOTE: Depending on the location you have selected for installation,
you may need to purchase and install a “Joist Hanger” for the support
of the outlet box. Make sure the joist hanger you purchase has been
designed for use with ceiling fans. (Fig.4)
Outlet box
ANGLED CEILING
MAXIMUM 18° ANGLE Provide strong
support
Ceiling
mounting
plate
Recessed
Outlet box
Fig. 2
Fig. 4
Fig. 3
Fig. 1
Outlet box
Outlet box

HANGING THE MOTOR ASSEMBLY
REMEMBERREMEMBER to turn off the power before you begin installation. This is
necessary for your safety and also the proper programming of the control
system. To properly install your ceiling fan, follow the steps below.
Step 1.Step 1. Before attaching fan to outlet box (not included), ensure the outlet box
is securely fastened to at least two points to a structural ceiling member
(a loose box will cause the fan to wobble). Install the screws and washers
included with the outlet box. NOTE:NOTE: Do not lock the screws completely, just
lock half.
Pass the 120 volt supply wires form the ceiling outlet box through the center
of the ceiling mounting bracket.(Fig. 5)
Step 2.Step 2. Align the slot holes on the mounting bracket with the screws, and
push the mounting bracket to the screws, then tighten the screws. (Fig. 6
and 7)
Fig. 5
Fig. 6
Fig. 7
52" Bezel LED | 7
Outlet Box
Mounting Bracket
Washer
Screw

8 | KICHLER.COM
HANGING THE MOTOR ASSEMBLY
Step 3.Step 3. Remove the hairpin and clevis pin from the downrod assembly, retain
for later use.(Fig.8)
Step 4.Step 4. Loosen the two set screws on the motor coupling.(Fig. 9)
Step 5.Step 5. Place the coupling cover, canopy hole cover and canopy over the
coupling found on the top of the motor assembly. Carefully feed fan wires
from the motor assembly through the downrod, then insert the downrod into
the coupling.(Fig.10)
Fig. 10
Set Screw
Downrod
Canopy
Canopy Hole Cover
Coupling Cover
Coupling
Clevis Pin
Hair pin
Fig. 9
Fig. 8

52" Bezel LED | 9
HANGING THE MOTOR ASSEMBLY
Step 6.Step 6. Pass the clevis pin through the downrod and coupling found on the
motor assembly, and secure with the hair pin. Tighten set screws found on
the coupling. (Fig. 11 )
Step 7.Step 7. Now lift the motor body into position and place the hanger ball into
the mounting bracket. Rotate until the "Check Tab" has dropped into the
"Registration Slot" and seats firmly. (Fig. 12) The entire motor body should
not rotate if this is done correctly.
WARNING:WARNING: Failure to properly seat the "Check Tab" can damage the ceiling
fan during operation.
Fig. 12
Fig. 11
Hairpin
Clevis Pin
Set Screw
OK NO
Coupling
Registration Slot
Check Tab

10 | KICHLER.COM
ELECTRICAL CONNECTIONS
WARNING:WARNING: To avoid possible electrical shock, be sure you have turned offTo avoid possible electrical shock, be sure you have turned off
the power at the main circuit panel before wiring. Follow the steps belowthe power at the main circuit panel before wiring. Follow the steps below
to connect the fan to your household wiring. Use the wire connecting nutsto connect the fan to your household wiring. Use the wire connecting nuts
supplied with your fan. Secure the connector with electrical tape. Make suresupplied with your fan. Secure the connector with electrical tape. Make sure
there are no loose wire stands or connections.there are no loose wire stands or connections.
WARNING:WARNING: If your house wires are different colors than referenced in thisIf your house wires are different colors than referenced in this
manual, stop immediately. A professional electrician is recommended tomanual, stop immediately. A professional electrician is recommended to
determine proper wiring.determine proper wiring.
Step 1.Step 1. Insert the receiver into the mounting bracket, and keep flat inInsert the receiver into the mounting bracket, and keep flat in
opposition of ceiling. Cut o excess fixture wires approximately 6 to 9 inchesopposition of ceiling. Cut o excess fixture wires approximately 6 to 9 inches
above top of the downrod assembly. Strip insulation o 1/2 in. from the end ofabove top of the downrod assembly. Strip insulation o 1/2 in. from the end of
each fixture wire. (Fig. 13)each fixture wire. (Fig. 13)
Step 2.Step 2. Motor to Receiver Electrical Connections: Connect the BLACKMotor to Receiver Electrical Connections: Connect the BLACK
wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver.wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver.
Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTORConnect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR
N" from the receiver. Connect the BLUE wire from the fan to the BLUE wireN" from the receiver. Connect the BLUE wire from the fan to the BLUE wire
marked "FOR LIGHT" from the receiver. Secure all the wire connections withmarked "FOR LIGHT" from the receiver. Secure all the wire connections with
the plastic wire connectors provided. (Fig. 14)the plastic wire connectors provided. (Fig. 14)
Step 3.Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect theRemote Receiver to Outlet Box Electrical Connections: Connect the
BLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" fromBLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" from
the receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITEthe receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITE
wire marked "AC IN N" from the receiver. Secure all the wire connections withwire marked "AC IN N" from the receiver. Secure all the wire connections with
the plastic wire connectors provided. (Fig. 14)the plastic wire connectors provided. (Fig. 14)
Fig. 13a Fig. 13b
Fig. 14
Receiver Mounting Bracket
Green or bare copper (ground)
AC IN N(White)
AC IN L(Black)
Black ("AC IN L") White("AC IN N")
White("TO MOTOR N")
Ground wire
Ground wire
White (Neutral)
Receiver
Black ("TO MOTOR L")
Black (motor)
Blue(FOR LIGHT)
Blue(for light)
6 to 9 in.