Kichler Lighting ARKVILLE 39540 User manual

Français p. 8
Español p. 15
ITEM #4145466
MODEL #39540
ARKVILLE 1-LIGHT OUTDOOR WALL MOUNT
1
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
2

1
Canopy 1
Mounting Bracket 1
Socket 1
Glass Panel 3
Hood Screw 2
PACKAGE CONTENTS
23
A
B
C
D
F 1
E
PART DESCRIPTION QUANTITY
A
EF
D
C
B
Hood

2 43
HARDWARE CONTENTS
Wire
Connector
AA
Short
Machine
Screw
BB
Qty: 3
Qty: 2
CC
Mounting
Screw
Qty: 4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
WARNING
• CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during
the installation.
• WARNING:
This fixture is intended for installation in accordance with the National Electrical Code (NEC)
and all local code specifications. If you are not familiar with code requirements, installation by a
certified electrician is recommended.
• Do not use bulbs with wattage greater than specified on this fixture.
• California Proposition 65
WARNING: This product can expose you to chemicals including lead, which is known to
the State of California to cause cancer, birth defects, or other reproductive harm.
For more information, go to http://www.P65Warnings.ca.gov
CAUTION
• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate
completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave
parts out, or use any parts that are worn out or broken. Failure to obey this instruction could
invalidate ETL listing and/or C.S.A. certification of this fixture.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated assembly time: 30 minutes to 1 hour
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, safety glasses.

4 53
ASSEMBLY INSTRUCTIONS
Short Machine
Screw x 2
BB
Hardware Used
1. With the flanges of the mounting bracket (B) in
the 9 and 3 o’clock position, attach the
mounting bracket to the outlet box (not
included) using the short machine screws (BB).
1 Outlet Box
B
BB
Hardware Used
x 3Wire Connector
AA
2. Wire connection guide:
Ground wire:
• For installation in the United States: Wrap
ground wire from outlet box around ground
screw on mounting bracket (B) no less than 2
in. from wire end. Tighten ground screw. If
fixture is supplied with a ground wire, connect
to outlet ground wire with a wire connector
(AA).
• For installation in Canada: If fixture is supplied
with ground wire, wrap ground wire around
ground screw on mounting bracket (B).
Tighten ground screw. Connect fixture ground
wire to outlet ground wire with a wire
connector (AA).
Supply wires:
• Connect the Neutral (White) supply wire from
the outlet box to the Neutral fixture wire (White
or Parallel Cord “D” shaped and ribbed).
• Connect the Hot (Black) supply wire from the
outlet box to the Hot fixture wire (Black or
Parallel Cord round and smooth).
NOTE:
Fixture wires will either be:
• Black and White.
• Parallel Cord SPT-1 lamp wire with one
round smooth wire and one “D” shaped
ribbed wire.
2
BARE COPPER,
OR GREEN
GROUND
SUPPLY WIRE
BARE COPPER,
OR GREEN
GROUND
FIXTURE
WIRE
BLACK FIXTURE
WIRE
OR
WHITE FIXTURE
WIRE
BLACK SUPPLY
WIRE
BLACK SUPPLY
WIRE
PARALLEL
FIXTURE CORD
(ROUND AND
SMOOTH)
PARALLEL FIXTURE
CORD (“D” SHAPED
AND RIDGED
)
WHITE SUPPLY
WIRE
WHITE SUPPLY
WIRE
AA

ASSEMBLY INSTRUCTIONS
4 5 6
4. Push fixture to wall over the flanges of the
mounting bracket (B), carefully aligning holes
in flanges of mounting bracket with holes in
canopy (A). Be sure not to pinch wires
between wall and canopy of fixture. Screw
the four (4) mounting screws (CC) into the
canopy and mounting bracket flanges to
secure fixture to wall. Tighten to secure.
x 4
CC Mounting
Screws
Hardware Used
3. Mounting surface should be clean, dry, flat and
1/4 in. larger than the canopy (A) on all sides.
Any gaps between the mounting surface and
canopy (A) exceeding 3/16 in. should be
corrected as required with silicone caulking
compound. Caulk completely around where the
back of canopy (A) meets the wall surface to
prevent water from seeping into outlet box.
3
A
4
CC
A
B

ASSEMBLY INSTRUCTIONS
5 6
5.
Remove two (2) hood screws (E) and lift hood
(F) o fixture. Insert 60-watt max E26
medium base bulb or CFL/LED equivalent
(not included) into socket (C).
E
5
7
F
6. Replace hood (F) on fixture and secure in
place with hood screws (E).
E
6
F
C

6
REV 05-AUG-2021
Distributed by:
Kichler Lighting LLC
7711 East Pleasant Valley Rd
Cleveland, OH 44131
Printed in China
7
CARE AND MAINTENANCE
TROUBLESHOOTING
Fixture does not light. 1. Fixture may be wired incorrectly.
1. Check wiring.
2. Worn or broken bulb. 2. Replace bulb.
1. Check wiring.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
• Always be certain that electric current is turned o before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on
fixture, as it will damage the metal finish.

ARTICLE # 4145466
MODÈLE # 39540
APPLIQUE MURALE POUR L’EXTÉRIEUR
À 1 LUMIÈRES ARKVILLE
8
Des questions, des problèmes, des pièces manquantes? Avant de retourner le produit à
votre détaillant, appelez notre service à la clientèle au 1-800-554-6504, entre 8 h et 16 h 30
(HNE) du lundi au vendredi.
JOIGNEZ VOTRE REÇU ICI
Numéro de série Date d’achat
9

8
Pavillon 1
Support de Fixation 1
Douille 1
Panneau de Verre 3
Vis du Cache
2
CONTENU DE L’EMBALLAGE
910
A
B
C
D
E
PIÈCE DESCRIPTION QUANTITÉ
F 1
Cache
A
EF
D
C
B

9 1110
QUINCAILLERIE INCLUSE
Capuchon
de Connexion
AA
Vis à
Métaux
Courte
BB
Qté. : 3
Qté. : 2
CC
Vis de
Montage
Qté. : 4
CONSIGNES DE SÉCURITÉ
Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler,
d’utiliser ou d’installer ce produit.
AVERTISSEMENT
• ATTENTION – RISQUE DE DÉCHARGES ÉLECTRIQUES –
Couper le courant au niveau du panneau du disjoncteur du circuit principal ou de la boîte à
fusibles principale avant de procéder à l’installation.
• ATTENTION:
Ce luminaire doit être installé conformément aux codes d’électricité nationaux (NEC) et
satisfaire toutes les spécifications des codes locaux. Si vous ne connaissez pas les exigences de
ces codes, il est recommandé de confier l’installation à un électricien certifié.
• N’utilisez pas d’ampoules dont la puissance dépasse la puissance nominale indiquée sur ce
luminaire.
• Proposition 65 de la Californie
AVERTISSEMENT: cet article peut vous exposer à des produits chimiques, notamment
les composés de plomb identifiés par l'État de la Californie comme cause de cancer,
malformations congénitales ou autres troubles de l'appareil reproducteur.
Pour de plus amples informations, consultez le site http://www.P65Warnings.ca.gov
ATTENTION
• Si vous avez des doutes à propos de l’installation, ou si le luminaire ne fonctionne pas
correctement, veuillez communiquer avec un électricien qualifié.
• Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez
pas les pièces, n'en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le
non-respect de ces instructions peut annuler l’homologation ETL ou C.S.A. du luminaire.
PRÉPARATION
Avant de commencer l’assemblage du produit, assurez-vous que toutes les pièces sont présentes.
Comparez les pièces avec la liste du contenu de l’emballage et la liste de la quincaillerie. En cas de
pièces manquantes ou endommagées, ne tentez pas d’assembler le produit.
Temps d’assemblage approximatif : de 30 à 60 minutes.
Outils nécessaires pour l’assemblage (non inclus) : tournevis cruciforme, tournevis à tête plate,
pinces à dénuder, ruban isolant, escabeau et lunettes de sécurité.