Kicker PXA200.2 User manual

KICKER
AMP
SPEAKER
&
INSTALLATION GUIDE
FOR USE
WITH
KAWASAKI
VAQUERO
INCLUDED IN THIS FIT
KIT:
-7
Step-by-step Installation Guide
-7
All
Necessary Hardware
-7
5
1/4"
Kicker Speakers Pair -
8-
32
x
1/2"
Button Head Bolts
-7
KickerAmp 100W/50W -
8-
32
Nylock Nuts
-7
Stainless Steel Mounting Bracket
-7
Black Heat Shrink
-7
Custom Wiring Harness
-7
Black Cable Tie

KLOCK
WERKS
I
VAQUERO
KICKER INSTALLATION ' 2
GETTING STARTED I
*Please reference model appropriate service manual
for
procedures and torque specifications.
1.
Protect painted surfaces
with
a soft cloth.
2.
Remove the seat.
3.
Remove plastic battery cover.
4.
Disconnect battery.
AMP INSTALLATION
5.
Follow the proper procedure to remove the
outer
fairing.
6.
Install
amplifier
onto bracket Slide the
amplifier
into the
left
side of the bracket and use supplied hardware
to bolt the amp to the bracket.
(Pic 1)
7.
Remove the two fasteners holding the radio chassis to the
inner
fairing bracket
8.
Set the
amplifier
assembly
on
top of the
inner
fairing bracket and use the hardware removed in step 7
to fasten it back onto the
inner
fairing bracket.
(Pic
2)
HARNESS INSTALLATION
9.
Follow the proper procedure to remove the
fuel
tank.
10. Plug harness into the amplifier.
11. Route the
right
side speakerwires behind the
amplifier
toward the
right
side speaker pod.
12. Route the left side
wires
behind the fairing support toward the
left
side speaker pod.
(pic
3)
13. The blue
wire
is to
be
installed in the accessory power source
on
the
left
side of the fairing.
It is a tan wire with a double
barrel
terminal.
(pic
4)
14.
Route the power leads along the main harness.
(pic 5):
1.
Along the
left
side of the frame neck.
2.
Under the black
wire
retainer
on
the neck.
3.
Under the
front
fuel
tank bumper.
4.
Underneath the anodized
wire
retainer.
(You
will
have to loosen the bracket)
5.
Under the
rear
fuel tank bumper.
6.
Follow the harness down the
right
side of the frame and
under
the seat.
15. The blue lead
under
the seat would
be
used if installing a second amplifier, but
whether
used
or
not,
cover
with
supplied heat
shrink
to reduce the
risk
of a short.

K.LOCK
WERKS
I
VAQUERO
KICKER
INSTALLATION
3
SPEAKER INSTALLATION
16.
Remove the
four
Phillips head screws,
pull
the speaker out of its housing and unplug the stock speaker wires.
17.
Take
the left side speaker wires and insert them through the hole in the bottom of the speaker pod. (pic
6)
18.
Plug the male ends from the
amplifier
harness into the stock speaker terminals. (pic
7)
19.
Plug the female ends from the
amplifier
harness onto the Kicker speaker and refasten
it
to the housing with
the Phillips head screws removed in step
16.
(pic 8)
20.
Repeat
for
the right side speaker.
21.
Thread the positive power lead into the protective red
cap
and fasten to the battery. (pic
9)
22.
Connect the negative power lead and check system operation.
23.
Be
sure to check that none of the wires
will
be
in a bind when the steering head is turned
fully
to the right
or
the left.
Note: At this time, it is highly recommended to follow the guidelines in your Kicker
PX
100.2 owner's manual
to set up the amplifier. Klock Werks recommends that the dip switches
be
set up
as
follows:
AUTO
TURN-ON -
12V
INPUT LEVEL-
HI
HI-PASS-
OFF
INPUT
GAIN
CONTROL- Follow the instructions in your Kicker
PX
100.2 owner's manual
Pg.
4
24.
Disconnect the negative battery
terminal
and carefully reassemble motorcycle.
25.
Connect negative battery terminal, install the battery cover and seat and enjoy your Kicker audio system!

IMPORTANT
Thank you for purchasing a Klock Werks®
Fit
Kit equipped with industry leading
KICKER®
speakers and amplifier.
There are
two
models of amplifier that may be used
in
this
kit:
PX1
00.2
or PXA200.2.
Set the switches to the following
configuration for the PX1 00.2
IMPORTANT:
Turn
the gain
all
the way down,
then increase to 20%, about
1/4
turn from 0.
Product ships with gain at maximum setting.
Set the switches to the following
configuration for the PXA200.2
Your gain rotary
should look like
this.
Be
careful
not
to set it
to 80% instead!
GAIN
All
other installation procedures, including wiring and mounting, are the same for either amplifier.
Enjoy your Performance PowerSports equipment as engineered by Klock Werks and KICKER!
KVVSS-082415-C

PXA STEREO AMPLIFIER
PXA200.2
Owner’s Manual | English
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE PXA.2
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER PXA.2-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE PXA.2
PXA Amplifiers
2015 PX Stereo Amplifier Rev B.indd 1 8/26/2014 3:26:37 PM

2
PXA.2-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifier. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifier. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the
amplifier.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the PXA harness to the
amplifier. A good ground connections is important. If this amplifier is mounted in the front fairing of a motorcycle, it
will be best to extend the ground wire all the way to the battery.
The PXA amplifiers have the capability to receive almost any level of input signal. If a Hi-Level signal is coming
from the speaker leads of the source unit, simply cut off the RCA jacks and connect it directly to the exposed
wires. Set the Input Level switch to Hi. Set the Auto Turn-On to DC. If speaker leads are not available from your
source unit, use an RCA stereo cable to connect directly to the RCA connectors of the PXA amplifier. Set the
Input Level switch to Lo. Set the Auto Turn-On switch to +12V, and use the blue remote trigger wire to turn the
amplifier on.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: PXA200.2
RMS Power [Watts]
@ 14.4V, 4Ω stereo, ≤ 1% THD+N
@ 14.4V, 2Ω stereo, ≤ 1% THD+N
@ 14.4V, 1Ω stereo, ≤ 1% THD+N
25 x 2
50 x 2
100 x 2
Length [in, cm] 7, 17.8
Height [in, cm] 1-5/8, 4
Width [in, cm] 3-7/16, 8.7
Frequency Response [Hz] 10 - 20k
Signal-to-Noise Ratio [dB] 95
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Selectable HI or OFF; 60Hz, 80Hz or 120Hz; 12dB/octave slope
Pro Tip: To get the best performance from your new KICKER Amplifier and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: PXA200.2
IMPORTANT SAFETY WARNING – PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER IN A
DISTORTED OR CLIPPED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING
FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE.
2015 PX Stereo Amplifier Rev B.indd 2 8/26/2014 3:26:45 PM

3
12V
Model External Fuse
PXA200.2 1 x 15 Ampere
battery
external fuse
(15A)
remote
turn-on
speaker outputs
++--
RCA inputs
(remove to use
hi-level input)
bare-metal chassis
ground
bare-metal chassis ground
≤18”
(45cm)
≤24”
(60cm)
Cut the looped red power cable located on the PXA harness and install a 15A fuse. Fuse installation should be
within 18” (45cm) of the battery and in-line with the harness’ power cable, which is connected to your amplifier. If
you ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the
last wire disconnected from the amplifier--just the opposite as when you installed it.
KICKER KISL (optional)
from source unit high-level speaker outputs
to amplifier
2015 PX Stereo Amplifier Rev B.indd 3 8/26/2014 3:26:45 PM

4
OPERATION
Automatic Turn-On Selection: The PXA series offers two automatic turn-on modes that can be selected on
the end panel; +12V or DC Offset. Using the DC Offset mode causes the REM terminal wire to have +12V out
for turning on additional amplifiers.
• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from the PXA harness. Run 18
gauge wire from the Remote Turn-On Lead on your source unit to the REM wire on the PXA harness. (Best
for Lo-Level input)
• DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when
the source unit has been turned on. (Best for Hi-Level input)
Input Level: The RCA inputs on KICKER PXA amplifiers are capable of receiving either Hi or Low-level signals
from your source unit. When using a Hi-Level signal, simply set the Input Level switch on the amplifier to HI.
HI-PASS Switches: Use the HI-PASS switches behind the protective rubber covering of the amplifier to set the
internal crossover. Choose a cutoff of 60Hz, 80Hz, 120Hz, or OFF depending on the configuration of switches 1
and 2. Never change the switches with the audio system on!
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it
down a little.
HI-PASS FILTER LO 12V
HI DC
INPUT LEVEL
AUTO TURN-ON
60Hz 80Hz 120Hz OFF
2015 PX Stereo Amplifier Rev B.indd 4 8/26/2014 3:26:45 PM

5
TROUBLESHOOTING
If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Power
Protection LED on the side power panel of your Kicker PXA series amplifier. Depending on the state of the
amplifier and the vehicle’s charging system, the LED will glow either Red or Blue. When the blue LED is lit this
indicates the amplifier is turned on and no trouble exists.
Blue LED off, no output? With a Volt Ohm Meter (VOM) check the following: n+12 volt power terminal
(should read +12V to +16V) oRemote turn-on terminal (should read +12V to +16V) pCheck for reversed
power and ground connections qGround terminal, for proper conductivity. rFor Hi-Level input, check input
wires for +6V.
Blue LED on, no output? Check the following: nRCA connections oTest speaker outputs with a “known”
good speaker. pSubstitute source unit with a “known” good source unit. qCheck for a signal in the RCA
cable feeding the amplifier with the VOM meter set to measure “AC” voltage.
Protection LED flashing with loud music? The red LED indicates low battery voltage. Check all the
connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or
replace your vehicle’s alternator.
Protection LED on, no output? nAmplifier is very hot =thermal protection is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow around
the amplifier. oAmplifier shuts down only while vehicle is running = voltage protection circuitry is engaged.
Voltage to the amplifier is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical
system inspected. pAmplifier will only play at low volume levels = short circuit protection is engaged. Check
for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)
operating below the minimum recommended impedance.
No or low output? nCheck the balance control on source unit oCheck the RCA (or speaker input) and
speaker output connections.
Alternator noise-whining sound with engine’s RPM? nCheck for damaged RCA (or speaker input) cable
oCheck the routing of RCA (or speaker input) cable pCheck the source unit for proper grounding qCheck
the gain settings and turn them down if they are set too high.
Reduced bass response? Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s); if the bass improves, the speaker was out of phase.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units.
Some head units may require additional grounding to prevent noise from entering the audio signal. If you are
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the
head unit to the chassis will remedy this issue.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the
vehicle.
If you have more questions about the installation or operation of
your new KICKER product, see the Authorized KICKER Dealer
where you made your purchase. For more advice on installation,
click on the SUPPORT tab on the KICKER homepage, www.
kicker.com. Choose the TECHNICAL SUPPORT tab, choose
the subject you are interested in, and then download or view the
corresponding information. Please E-mail [e-mail] or
call Technical Services [phone] for unanswered or specific
questions.
2015 PX Stereo Amplifier Rev B.indd 5 8/26/2014 3:26:45 PM

18
ELECTRONICS LIMITED WARRANTY
When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material
and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase. If this product is
identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from date of original
purchase. In all cases you must have the original receipt. Should service be necessary under this warranty for any reason
due to manufacturing defect or malfunction during the warranty period, KICKER will repair or replace (at its discretion)
the defective merchandise with equivalent merchandise. Warranty replacements may have cosmetic scratches and
blemishes. Discontinued products may be replaced with more current equivalent products. This warranty is valid only for
the original purchaser and is not extended to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are limited in duration to a period of the express warranty as provided herein beginning with the date of
the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties; therefore, these exclusions may not apply to you. This warranty
gives you specific legal rights; however you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at [phone] for a Return Merchandise Authorization (RMA) number. Package only
the defective items in a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing the Customer’s
name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof-of-
purchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization (RMA) number
o Products purchased from an UNAUTHORIZED dealer
o Freight Damage
o The cost of shipping product to KICKER
o Service performed by anyone other than KICKER
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.)
returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps
may void your warranty. Any questions can be directed to the KICKER Customer Service Department at [phone].
Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty
policies.
Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most
current information.
stillwaterdesigns
15PXA.2-B-20140826
2015 PX Stereo Amplifier Rev B.indd 18 8/26/2014 3:26:46 PM

19
P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510
INTERNATIONAL WARRANTY
Contact your International KICKER dealer or distributor concerning
specific procedures for your country’s warranty policies.
WARNING: KICKER products are capable of producing sound levels
that can permanently damage your hearing! Turning up a system to a
level that has audible distortion is more damaging to your ears than
listening to an undistorted system at the same volume level. The
threshold of pain is always an indicator that the sound level is too loud
and may permanently damage your hearing. Please use common
sense when controlling volume.
GARANTÍA INTERNACIONAL Versión Español
Comuníquese con su concesionario o distribuidor KICKER internacional para obtener infor ación sobre procedimientos específicos
relacionados con las normas de garantía de su país.
ADVERTENCIA: Los excitadores KICKER son capaces de producir niveles de sonido que pueden dañar permanentemente
el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el oído que escuchar un
sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es muy fuerte y que puede dañar
permanentemente el oído. Sea precavido cuando controle el volumen.
La frase “combustible para vivir la vida Livin’ Loud™ a todo volumen” se refiere al entusiasmo por la vida que la marca KICKER
de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible (“a todo volumen”)
en todo sentido. La línea de altavoces y amplificadores KICKER es la mejor del mercado de audio de automóviles y por lo tanto
representa el “combustible” para vivir a todo volumen en el área de “estéreos de automóvil” de la vida de nuestros clientes.
Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos locales sobre ruido en cuanto a los
niveles legales y apropiados de audición fuera del vehículo.
INTERNATIONALE GARANTIE Deutsche Version
Nehmen Sie mit Ihren internationalen KICKER-Fachhändler oder Vertrieb Kontakt auf, um Details über die Garantieleistungen in
Ihrem Land zu erfahren.
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann! Wenn Sie ein
System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass der Schallpegel zu laut ist und zu
permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung bitte vernünftig!
Der Slogan “Treibstoff für Livin’ Loud” bezieht sich auf die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten (“Livin’ Loud”) zu streben. Die
Lautsprecher und Verstärker von KICKER sind auf dem Markt für Auto-Soundsysteme führend und stellen somit den “Treibstoff”
für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren Kunden, sich bezüglich der zugelassenen und
passenden Lautstärkepegel außerhalb des Autos an die örtlichen Lärmvorschriften zu halten.
GARANTIE INTERNATIONALE Version Française
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou distributeur
International KICKER.
AVERTISSEMENT: Les haut-parleurs KICKER ont la capacité de produire des niveaux sonores pouvant endommager l’ouïe de
façon irréversible ! L’augmentation du volume d’un système jusqu’à un niveau présentant une distorsion audible endommage
davantage l’ouïe que l’écoute d’un système sans distorsion au même volume. Le seuil de la douleur est toujours le signe que le
niveau sonore est trop élevé et risque d’endommager l’ouïe de façon irréversible. Réglez le volume en faisant prevue de bon sens!
L’expression “ carburant pour vivre plein pot “ fait référence au dynamisme de la marque KICKER d’équipements audio pour
véhicules et a pour but d’encourager nos clients à faire le maximum (“ vivre plein pot “) dans tous les aspects de leur vie. Les
haut-parleurs et amplificateurs KICKER sont les meilleurs dans le domaine des équipements audio et représentent donc pour nos
client le “ carburant pour vivre plein pot “ dans l’aspect “ installation audio de véhicule “ de leur vie. Nous encourageons tous nos
clients à respecter toutes les lois et réglementations locales relatives aux niveaux sonores acceptables à l’extérieur des véhicules.
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure
does not amount to a major failure.
2015 PX Stereo Amplifier Rev B.indd 19 8/26/2014 3:26:46 PM

©2014 Stillwater Designs®
2015 PX Stereo Amplifier Rev B.indd 20 8/26/2014 3:26:46 PM

lfKICKER
PS5250 COAXIAL SPEAKERS
Owner's Manual
Authorized KICKER Dealer:
Purchase Date:
PERFORMANCE
Woofer Size
Tweeter Size
Frequency Response
Max Amplifier Power
Sensitivity
[1 W/1 m]
Nominal Impedance
Weight
Mounting Hole Diameter
Mounting Depth
5-1/4" [133mm]
3/4" [20mm]
60Hz-20kHz
1 oow PEAK I 50W RMS
88.3dB
20
12.6o z [358g]
4-7 /8 " [124mm)
2-3/16" [56mm]
[9/16"J
14mm
[2 3/16"]
56mm
[4 7/8"]
124mm
The PS5250 Coaxial Speakers are KI CKER's upgrade for Harley-Davidson® premium audio systems (2006
and later) and s
imil ar tou rin g bikes. Please refer to your bike 's factory service manual for dissassembly/
installation information.
Typi cally, you should retain al l factory sc rews, ha rd ware, and grilles when upgrading your
bike to a KI
CK ER system. The following diagrams show how to install the PS 5250 speakers in a Harley-Davidson
bike with "batw
in g" style fairing (2006 and later). Note: The PS5250 is a 2-ohm speaker. Do not
install in systems that are not 2-ohm stable!
1. Remove front side of fairing.
7xTorxT25 ®
2
PS COAXIALS

2. Remove factory speakers.
Remove the factory speaker connectors.
Retain the 3 factory screws.
Remove the factory speakers from the factory angle mount (be careful not to damage the angle mount).
[viewed from front of bike]
factory speaker connectors
3. Prepare PS5250 for installation.
Install the KICKER badges onto the grilles; bend the rear posts to secu re them in place.
For Harley "batwing" installations, replace the factory grilles with
KICKER grilles. factory screws x 3
KICKER PS525~ l
For all other Harley applications, use the factory grilles only.
recommended
badge location
KICKER grille
factory grille
(remove for "batwing" only)
4. Install PS5250 in factory location.
Use the 3 factory screws.
Connect the factory speaker connectors to the PS5250 terminals.
Re-install your bike's front fairing
in the reverse order you disassembled it.
install short screw at
bottom
3

ACOUSTICS LIMITED WARRANTY
KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it
is warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases you must have the original receipt.
Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction during the
warranty period,
KICKER will repair or replace (at its discretion) the defective merchandise with equivalent merchandise
at no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued products may be
replaced with more current equivalent products. This warranty
is valid only for the original purchaser and is not extended
to owners of the product subsequent to the original purchaser. Any applicable implied warranties
are limited in duration
to a period of the express warranty as provided herein beginning with the date of the original purchase
at retail, and no
warranties, whether express or implied, shall apply to this product thereafter. Some states
do not allow limitations on
implied warranties; therefore these exclusions may not apply to you. This warranty gives you specific legal rights; however
you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance
in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly.
You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at (405)
624-8510 for a Return Merchandise Authorization (RMA) number. Package only
the defective items
in a package that will prevent shipping damage, and return to:
Stillwater Designs,
3100 North Husband St, Stillwater, OK 7 4075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return of functioning items increases your return freight charges. Non-defective items
will be returned freightcollect to you.
For example,
if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing the Customer's
name, Dealer's name and invoice number, and product purchased. Warranty expiration on items without proof-of-
purchase
will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COO,
will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or
UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products returned without a Return Merchandise Authorization
(RMA) number
o Freight Damage
o The cost of shipping product to
KICKER
o Service performed by anyone other than KICKER 5) StillwaterdeSignS
HOW LONG WILL IT TAKE?
((
KICKER strives to maintain a goal of 48-hour service for all acoustics (subwoofers, midrange drivers, tweeters,
crossovers, etc) returns. Delays may be incurred
if lack of replacement inventory or parts is encountered. Failure to
follow these steps may void your warranty. Any questions can be directed to the
KICKER Customer Service Department
at [phone]. Contact your International
KICKER dealer or distributor concerning specific procedures for your
country's warranty policies.
Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most
current information.
P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • [phone]
10PS5250-C-20091208
10 PS COAXIALS

INTERNATIONAL WARRANTY
Contact your International KICKER dealer or distributor concerning specific procedures for your country's warranty policies.
WARNING:
KICKER
products are capable of producing sound levels that can permanently damage your hearing! Turning up a
system to a
level
that has audible distortion
is
more damaging to your ears than listening to
an
undistorted system at the same
volume level. The threshold of pain
is
always
an
indicator that the sound level
is
too loud and may permanently damage your
hearing. Please use common sense when controlling volume.
GARANTfA
INTERNACIONAL
Version
Espanol
Comuniquese con
su
concesionario o distribuidor
KICKER
internacional para obtener infor aci6n sobre procedimientos especificos
relacionados con las normas de garantia
de
su
pais.
ADVERTENCIA: Los excitadores KICKER son capaces de producir niveles
de
sonido que pueden danar permanentemente
el
oido. Subir
el
volumen del sistema hasta
un
nivel que produzca distorsi6n es mas danino para
el
oido que escuchar
un
sistema sin distorsi6n
al
mismo volumen.
El
dolor es siempre una indicaci6n de que
el
sonido es muy fuerte y que puede danar
permanentemente
el
oido. Sea precavido cuando controle
el
volumen.
La
frase "combustible para vivir
Ia
vida Livin' Loud™ a todo volumen" se refiere
al
entusiasmo
porIa
vida que
Ia
marca KICKER
de estereos de autom6vil representa y a
Ia
recomendaci6n a nuestros clientes de
que
vivan
lo
mejor posible
("a
todo volumen")
en
todo sentido. La linea de altavoces y amplificadores
KICKER
es
Ia
mejor del mercado
de
audio
de
autom6viles y por
lo
tanto
representa
el
"combustible" para vivir a todo volumen
en
el
area de "estereos
de
autom6vil" de
Ia
vida de nuestros clientes.
Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos locales sobre ruido
en
cuanto a los
niveles legales y apropiados de audici6n fuera del vehiculo.
INTERNATIONALE
GARANTIE
Deutsche
Version
Nehmen Sie mit lhren internationalen KICKER-Fachhandler oder Vertrieb Kontakt auf, um Details uber die Garantieleistungen
in
lhrem Land
zu
erfahren.
WARNUNG: KICKER-Treiber kbnnen einen Schallpegel erzeugen, der
zu
permanenten Gehbrschaden
fUhren
kann! Wenn Sie ein
System auf einen Pegel stellen, der hbrbare Verzerrungen erzeugt, schadet das lhren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstarkepegel. Die Schmerzschwelle ist immer eine Anzeige dafur, dass der Schallpegel
zu
laut ist und
zu
permanenten Gehorschaden
fUhren
kann. Seien Sie bei der Lautstarkeeinstellung bitte vernunftig!
Der Slogan "Treibstoff
fUr
Livin' Loud" bezieht sich auf die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen,
in
allen Aspekten ihres Lebens nach dem Besten ("Livin' Loud")
zu
streben. Die
Lautsprecher und Verstarker von KICKER sind auf dem Markt
fUr
Auto-Soundsysteme fuhrend und stellen somit den "Treibstoff"
fUr
das Autostereoerlebnis unserer Kunden
dar.
Wir empfehlen allen unseren Kunden, sich bezuglich der zugelassenen und
passenden Lautstarkepegel auBerhalb des Autos
an
die brtlichen Larmvorschriften
zu
halten.
GARANTIE
INTERNATIONALE
Version Frant;aise
Pour connaltre les procedures propres a
Ia
politique de garantie
de
votre pays, contactez votre revendeur ou distributeur
International
KICKER.
AVERTISSEMENT: Les haut-parleurs KICKER ont
Ia
capacite de produire des niveaux sonores pouvant endommager
l'ou'1'e
de
favon irreversible ! L'augmentation du volume d'un systeme jusqu'a
un
niveau presentant une distorsion audible endommage
davantage l'ouie que l'ecoute d'un systeme sans distorsion
au
meme volume.
Le
seuil
de
Ia
douleur est toujours
le
signe que
le
niveau sonore est trop eleve et risque d'endommager
l'ou'fe
de favon irreversible. Reglez
le
volume en faisant prevue de bon sens!
L'expression "carburant pour vivre plein
pot"
fait reference
au
dynamisme de
Ia
marque KICKER d'equipements audio pour
vehicules
eta
pour but d'encourager nos clients a faire
le
maximum
("
vivre plein
pot")
dans
tousles
aspects de leur vie. Les
haut-parleurs et amplificateurs KICKER sont les meilleurs dans
le
domaine des equipements audio et representent done pour nos
client
le"
carburant pour vivre plein
pot"
dans
l'aspect"
installation audio
de
vehicule"
de
leur
vie.
Nous encourageons tous nos
clients a respecter toutes les lois et reglementations locales relatives aux niveaux sonores acceptables a l'exterieur des vehicules.
Harley-Davidson
is
a registered trademark of Harley-Davidson,
Inc.
Harley-Davidson es una marca registrada de Harley-Davidson, Inc.
Harley-Davidson ist
ein
eingetragenes Warenzeichen von Harley-Davidson, Inc.
Harley-Davidson est une marque deposee de Harley-Davidson, Inc.
11