Kid Kustoms Roddlec User manual
Owner’s
Manual
6months - 6yrs or Max Weight 37.5 lbs (17kgs)
ASTM and EN Safety Standard Certified
This product is NOT suitable for running or skating. For safety reasons, do
notmodifythisproductinanyway,exceptwithKidKustomscertiedparts.
WWW.KIDKUSTOMS.COM
Please read this owner’s manual completely before assembling or
operating this product, and keep it for future maintenance or reference
when communicating with Kid Kustoms customer service. This
product should always be assembled or disassembled by an adult.
The Roddler™•Parts List 4
•Warnings 5
•Care & Maintenance 6
•Assembly 6-11
Accessory •Parts List 12
Conversion: •Warnings 13
Trike Kit •Assembly 14-15
Enzo Trike •Parts List 16
•Warnings 17
•Assembly 18
Limited Warranty 19
Contents
Congratulations on your purchase.
?
WWW.KIDKUSTOMS.COM
Stroller
Included in the Box
• Stroller front chassis assembly
• Stroller rear chassis assembly
• 2x 8mm screws
• Seat and Canopy
• Storage Basket
Note: Before assembly, unpack and inspect all parts listed above.
6months - 6yrs or Max Weight 37.5 lbs (17kgs)
ASTM and EN Safety Standard Certified
This product is NOT suitable for running or skating. For safety reasons, do not
modifythisproductinanyway,exceptwithKidKustomscertiedparts.
4
WARNING
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE FOLLOWING WARNINGS AND
ASSEMBLY INSTRUCTIONS AND KEEP FOR FUTURE REFERENCE.
• Adult assembly required.
• CAUTION: Keep small parts away from children during assembly
• To avoid injury ensure that your child is kept away when unfolding and folding this product
• AVOID SERIOUS INJURY from falling or sliding out ALWAYS use seat belt. Check frequently to make
sure the seat belt buckle is secure.
• ALWAYS keep fingers away from moving parts, when folding, unfolding or adjusting stroller to prevent
finger entrapment.
• ALWAYS make sure stroller is FULLY OPEN AND LOCKED before using.
• ALWAYS use the brakes when stroller is stopped, even when standing still for only a few moments!
The brake must always be on when putting the child in or taking child out.
• ALWAYS remove protective material and package material and dispose before assembly.
• NEVER lift the stroller with your child inside it.
• NEVER use stroller on stairs or escalators with your child in the stroller.
• NEVER rollerblade with stroller.
• NEVER allow children to play with or hang onto the stroller. NEVER allow children to climb into the
stroller unassisted. Stroller may tip over and injure child.
• This seat unit is not suitable for children under 6 months.
• This product is not suitable for running or skating.
• NEVER LEAVE CHILD UNATTENTED. Always keep visual when child is in the stroller.
• NEVER place or hang parcels, bags or accessories on the handle or on seat frame. The stroller may tip
over or cause the unit to become unstable.
• This product will become unstable if the manufacturer’s recommended load is exceeded.
• DO NOT carry additional children, goods or accessories in or on this product except as recommended
in the manufacturer’s instructions.
• NEVER carry more than one child in the stroller at a time.
• NEVER place more than 11-LBS. (5-kg) in the storage basket. If weight is exceeded, hazardous
unstable conditions may exist.
• STROLLER is for use with children who can sit up unassisted, and is NOT recommended for newborns.
• Only use accessories and replacement parts approved by Kid Kustoms LLC. Using unapproved
accessories could be dangerous.
Stroller
5
care & maintenance
• DO NOT USE ANY CHEMICALS.
• To clean the frame and fenders of the stroller, use a simple detail carnuba wax or just a damp
cloth towel.
• Never use abrasive cleaners on either the plastic section or the frame or bleach near the fabric
covers as this may cause discoloration or scratches.
• Clean the fabric seat with pure water and soft absorbent cloth.
• Inflate the tires between 85~95% of maximum pressure shown on the tire.
• A punctured inner tube can be repaired in the same way as a bicycle tire.
• Always deflate the tires when taking the stroller on an aircraft, as the air pressure difference
could cause the tires to burst.
6
C
B
stroller assembly instructions
Get Started
A
1Use the two included
8MM screws [A] to attach
front chassis [B] to rear
chassis [C]. Do not fully
tighten screws until after
completing Step 2.
2 The perimeter bars
connect with a small
pin system. Push the
small pin down slightly to
complete the full perimeter
of the seat surround.
3 After clicking tubes in
place, fully tighten the
chassis screws.
7
stroller assembly instructions
• Pull the seat down
around the perimeter
bars. Fasten the clips
on back side of seat to
attach the seat securely
to the perimeter bars.
• Take the two male and
female buckles on the
underside of the seat and
loop them around the
seat frame.
• Connect the buckles and
tighten any slack.
Connecting the Seat
8
stroller assembly instructions
TO FOLD
THE STROLLER
• Hold down the safety
lock [1], then pull the pull
pin [2] out as you slightly
press the chassis down to
release.
Dual Action Safety Lock
34
1
2
TO UNFOLD
THE STROLLER
• Hold down the safety
lock by pressing the
embroidery ‘PRESS’ logo
[3] on the seat, then use
the other hand to pull the
pull pin [2].
• Hold the pull pin in release
position and lift the
chassis up [4] until you
hear the pull pin click into
lock position again.
• Press down the back of seat
frame to be sure the pull pin
is rmly locked before you
place your child in the seat.
• To adjust handlebar height,
rotate the adjustment lock
two full rotations. To lock in
place, turn clockwise until
fully tightened.
Handlebar Height Adjustment
9
• To apply parking brake,
make sure the foot pedal
arm clicks into the down
position.
• Listen for the click of the
brake pins locking the
wheel.
Parking Brake
• Press the two red right
and left red button at the
same time and pull the two
red buckle up to release.
• Adjust child’s shoulder
height straps to rmly hold
position while seated in the
stroller.
• Never operate the stroller
unless child’s seatbelt is
fully fastened.
• Use the shoulder harness
anchors in the slots that
are closest to child’s
shoulder height. Use
slide adjuster for further
adjustment.
Kid Kustoms™Signature 5-Point Safety Harness
stroller assembly instructions
10
• The front wheel lock will
register when both the
front wheel and fender are
in the forward position.
• To operate, set front wheel
to face forward and push
in the Locking Arm.
Front Wheel Lock
• To install the Car Carrier
attachment kit, you must
rst remove the seat. (To
remove the seat, reverse
the steps in Connecting
the Seat, page 7).
• With the seat removed,
slide the brackets with
safety tube into the tube
collector brackets on the
stroller perimeter bars.
• Be sure the pins are fully
locked in place before
attaching the Car Carrier.
Car Seat Carrier Attachment (Optional)
stroller assembly instructions
11
Accessory Conversion: Trike Kit
Included in the Box
• Front chassis assembly
• Seat and post
Note: Before assembly, unpack and inspect all parts listed above.
3+ yrs or Max Weight 55 lbs (25kgs)
ASTM and EN Safety Standard Certified
This product is NOT suitable for running or skating. For safety reasons, do not
modifythisproductinanyway,exceptwithKidKustomscertiedparts.
12
WARNING
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE FOLLOWING WARNINGS AND
ASSEMBLY INSTRUCTIONS AND KEEP FOR FUTURE REFERENCE.
• Adult assembly required.
• CAUTION: Keep small parts away from children during assembly
• NEVER LEAVE CHILD UNATTENDED. Continuous adult supervision required.
• NEVER use near motor vehicles.
• NEVER use near swimming pools, hills, steps, or sloped driveways.
• ALWAYS ride on level ground to avoid tipping over.
• Rider must ALWAYS wear shoes.
• ONLY use with ONE rider to use at a time.
• ALWAYS sit in the seat while operating the products.
• 3+ YEARS OR MAX WEIGHT CAPACITY 55 LBS (25 KG).
• It is recommended that your child always wear a properly fitted helmet that
complies with ASTM and EN safety standards.
• To avoid burns, NEVER leave the products outside in the sun when not in use.
Accessory Conversion: Trike Kit
13
A
conversion kit assembly instructions
1 To remove the stroller headset
[A], loosen the two hex bolts
on the side and loosen the
fl anged cap screw (with Kid
Kustoms Logo) on top the of
stroller headset.
2 Remove the two 8mm
screws [B] that connect the
stroller front chassis and rear
chassis.
3 Remove the fl ange nut [C]
then lift off the top of the
chassis.
4 Follow the instructions on
page 15 to complete the
Trike assembly.
Get Started: Disassemble Stroller
B C
14
D
A
C
F
E
B
1 Attach stroller handlebar
and headset [A] to the
the Trike front chassis
assembly [C].
2 Use the two included
8MM screws [B] to attach
trike front chassis [C] to
rear chassis [D]. Be sure
to fully tighten screws.
3Thread the seat post
[E] into the center of the
chassis [D] and tighten the
safety nut rmly against
the chassis to avoid
rotation. Then Slide the
Seat [F] on the top of the
seat post.
3Tighten the two ½” nuts
on the side of seat bracket
to keep the seat from
spinning. To adjust the
seat for shorter legs, slide
the seat forward on the
seat post bracket before
tightening the ½” nuts.
Assemble Enzo Trike
If you are assembling an Enzo Trike, follow Trike assembly
instructions, page 18.
conversion kit assembly instructions
15
Enzo Trike
Included in the Box
• Chassis assembly
• Handlebar headset
• 2x 8mm screws
• Seat
• Headlight (Kustom Trike Only)
Note: Before assembly, unpack and inspect all parts listed above.
3+ yrs or Max Weight 55 lbs (25kgs)
ASTM and EN Safety Standard Certified
This product is NOT suitable for running or skating. For safety reasons, do not
modifythisproductinanyway,exceptwithKidKustomscertiedparts.
16
WARNING
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE FOLLOWING WARNINGS AND
ASSEMBLY INSTRUCTIONS AND KEEP FOR FUTURE REFERENCE.
• Adult assembly required.
• CAUTION: Keep small parts away from children during assembly
• NEVER LEAVE CHILD UNATTENDED. Continuous adult supervision required.
• NEVER use near motor vehicles.
• NEVER use near swimming pools, hills, steps, or sloped driveways.
• ALWAYS ride on level ground to avoid tipping over.
• Rider must ALWAYS wear shoes.
• ONLY use with ONE rider to use at a time.
• ALWAYS sit in the seat while operating the products.
• 3+ YEARS OR MAX WEIGHT CAPACITY 55 LBS (25 KG).
• It is recommended that your child always wear a properly fitted helmet that
complies with ASTM and EN safety standards.
• To avoid burns, NEVER leave the products outside in the sun when not in use.
Enzo Trike
17
C
B
E
D
trike assembly instructions
1 Use the two included
8MM screws [A] to attach
front stem chassis and
pedal wheel assembly
[B] to rear chassis [C].
Be sure to fully tighten
screws.
2Thread the seat post
[D] into the center of the
chassis [C] and tighten the
safety nut rmly against
the chassis to avoid
rotation. Then Slide the
Seat [E] on the top of the
seat post.
3Tighten the two ½" nuts
on the side of seat bracket
to keep the seat from
spinning. To adjust the
seat for shorter legs, slide
the seat forward on the
seat post bracket before
tightening the ½" nuts.
Get Started
A
If transforming your Roddler Stroller into an Enzo Trike, follow
Accessory Conversion Kit assembly instructions, page 15.
18
Limited WARRANTY
We guarantee that this product was manufactured
in accordance with the current ASTM and EN safety
requirements and quality standards which are
applicable to this product, and that this product
is free from defects in workmanship and material
at the time of purchase. During the production
process the product was subjected to various
quality checks. If this product, despite our efforts,
shows a material/manufacturing fault within the
warranty period of 24 months (with normal use as
described in the user instructions) we will comply
with the warranty terms and conditions. In this
case please contact your dealer. For extensive
information on applying the warranty terms and
conditions, you can contact the dealer or visit our
website: www.kidkustoms.com.
The warranty is not valid in the following cases:
• In case of a use or purpose other than
described in the manual.
• If the product is submitted for repair through
a dealer that is not authorized by Kid
Kustoms LLC.
• If the product is not supplied to the
manufacturer with the original purchase
receipt (via the retailer and/or importer).
• If repairs were carried out by third parties
or a dealer that is not authorized by Kid
Kustoms LLC.
• If the defect is the result of improper or careless
use or maintenance, negligence or impact
damage to the soft good and/or frame.
• If the parts show normal wear and tear that may
be expected from daily use of a product (wheels,
rotating and moving parts etc.)
Effective Date:
• The warranty takes effect on the date the
product is purchased.
Warranty terms:
• The warranty period applies for a period of 24
consecutive months. The warranty only applies
for the first owner and is non-transferable.
• Repair parts and service only applies to the
original purchase country.
What to do in case of defects:
• After purchasing the product, keep the purchase
receipt. The date of purchase must be clearly
visible on the receipt. Should problems or
defects arise please contact your retailer.
Exchanging or taking back the product cannot
be requested. Repairs do not give entitlement
to extension of the warranty. Products that are
returned directly to the manufacturer are not
eligible for warranty.
local dealer or distributor. (see www.kidkustoms.com for more information)
?
The word marks Kid Kustoms™, The Roddler™,thetagline‘Vintagetinsandnsforyourtots’andassociatedlogosaretrademarks.
Additionally, all products are protected by a provisional patent; This material may not be reproduced without the prior written
permission.For a detailed guideline to govern the use of Kid Kustoms™trade marks, please email: [email protected]
These conditions of use are governed by the laws of the state of California in the United States of California and you agree that the
Californian courts shall have exclusive jurisdiction in any dispute. To the extent that any part of these conditions of use is found to be
invalid, unlawful or unenforceable by any court of competent jurisdiction such part shall to that extent be severed from the remaining
termsallofwhichshallremaininfullforceandeectaspermittedbylaw.
19
Designed in California and Made in China
WWW.KIDKUSTOMS.COM
This manual suits for next models
1
Table of contents
