Kidde TM0058 User manual

VEGA STANDARD
AND LT
CONTROL PANEL
CONTROL/REPEATER PANEL
USER GUIDE
TM0058

2
1 GENERAL
The Vega is an Analogue Addressable Control Panel that provides up to one hundred
and twenty zones of fire detection. It can support more than of two thousand devices
across sixteen detection loops and provide a programmed text description for each
device to aid the user in device location.
The standard control panel fascia has a control membrane, status/zonal membrane
(24 zones) and can include an event printer.
The LT control panel fascia has a combined control and status/zonal membrane
(16 zones).
Figure 1 – Example 24 Zone Standard Control Panel
Figure 3 – Example Vega Graphical Display
Figure 2 – Example 16 Zone LT Control Panel

3
Figure 4 – Standard Control Panel Example Control Membrane
Figure 5 – Standard Control Panel Example Status/Zonal Membrane
Figure 6 – LT Control Panel Example Control Status/Zonal Membrane
2 PANEL DISPLAY
The Standard and LT Control Panel Membranes provide the user interface to the control
panel and include the following (refer Figure 3, 4 and 6):
An eight line by 40 character graphic Liquid Crystal Display (LCD) with backlight.
Six control buttons – Silence Buzzer, Scroll, Silence Alarms, Reset, Delay Override
and Evacuate.
Four Arrow buttons used for viewing and programming panel information.
12 button numeric keypad, which includes an Enter ( ) and Cancel ( ) button.
The Status/Zonal area of the Control Panel provides user information in the form of lights
and contains the following (refer Figure 5 and 6):
14 system Status lights (YELLOW) (Standard Panel Only).
One Fire Output light (RED). One Fire Output light (YELLOW) (LT Panel Only).
One Common Fault light (YELLOW)
One Alarm light (RED).
One Power On light (GREEN).
One Test light (YELLOW) (LT Panel Only).
One System Fault light (YELLOW) (LT Panel Only).
24 zonal Alarm lights (RED) and Fault lights (YELLOW) (Standard Panel Only).
16 zonal Alarm lights (RED) (LT Panel Only).
On the Standard Control Panel if more than 24 zones of detection are required,
additional zonal membranes are used to display the zonal information. These are
supplied in increments of 32 up to a maximum of 120.
CONTROL
BUTTONS
LIQUID CRYSTAL DISPLAY
8 LINE 40 CHARACTER
STATUS
WINDOWS
ZONE
WINDOWS
CONTROL
BUTTONS
LIQUID CRYSTAL DISPLAY
8 LINE 40 CHARACTER
STATUS
WINDOWS
ZONE
WINDOWS

4
4 WHEN AN ALARM CONDITION OCCURS
If a FIRE condition is detected in one or more zones (refer to Figures 7, 8 & 9):
The red ALARM light flashes.
The appropriate red ZONAL alarm light flashes.
The LCD shows the flashing message “FIRE”.
The alarm SOUNDER circuits are activated (unless isolated).
The audible BUZZER on the panel sounds in a constant mode.
The event can be viewed by operation of the button.
Further events can be viewed by operation of the ARROW buttons.
3 ACCESS TO CONTROLS AND MENUS
There are two access levels that enable the user to control the panel.
Access Level 1 is the normal operating level, where the green POWER ON light is on.
All other lights are normally off unless devices or outputs are isolated or panel faults
exist. The SILENCE BUZZER, DELAY OVERRIDE, SCROLL, ( )and ( )buttons are
operative. All other controls are inoperative.
Access Level 2 allows user access to all control buttons and available menu options.
A pass code is required to enter Access Level 2 (refer Figure 6).
To enter Access Level 2 operate any numeric key to obtain the password prompt.
Enter the pass code  and press .
The LCD shows the level of access in the top right hand corner.
To access the menu listing:
Press the 0button to show the top-level menu options, Isolate, List, Set and Test.
Press at any time to cancel an entry or to exit the menus and revert to Access Level 1.
If there is no operation of the panel control buttons for more than three minutes, the
menu access control automatically reverts to Level 1.
Figure 6 – Example Access Level 2

5
Figure 7 – Example ALARM Condition
Figure 8 – Standard Control Panel Example ALARM Condition
After the agreed fire strategy has been followed under guidance from the responsible
person(s) or fire brigade, the alarms can be silenced as follows:
Press the SILENCE BUZZER button (the audible buzzer stops, the ZONAL light and
the ALARM light continue flashing). The audible alarm circuits will continue to sound
unless previously isolated.
Enter Access Level 2 (refer to Access to Controls).
Press the SILENCE ALARMS button (the audible alarms stop) The red ZONAL light
and ALARM light will go constant.
When all zone fire conditions have been rectified, press the RESET button.
Press to revert to Access Level 1.
If another alarm condition occurs after the panel has been silenced, the new event will
re-sound the audible devices and operate the appropriate ZONAL and ALARM lights.
To silence the second event the authorized person(s) should repeat the above
procedure once the affected area has been investigated.
Note: If a fire condition still exists it may be necessary to clear smoke from the
affected area before the control panel is RESET. Failure to do this may cause
further activations.
GENERAL ALARM
INDICATION
ZONAL ALARM
INDICATION
Figure 9 – LT Control Panel Example ALARM Condition
GENERAL ALARM
INDICATION
ZONAL ALARM
INDICATION

6
5 WHEN A FAULT CONDITION OCCURS
If a FAULT condition is detected in one or more zones (refer Figure 10, 11 & 12):
The yellow COMMON FAULT light flashes
The relevant yellow ZONAL fault light flashes
The Liquid Crystal Display will show the flashing message “FAULT”.
The yellow DEVICE FAULT light flashes
The audible BUZZER on the panel sounds intermittently.
The event can be viewed by operation of the button.
Further events can be viewed by operation of the ARROW buttons.
Figure 10 – Example FAULT Condition
Figure 11 – Standard Control Panel Example FAULT Condition
COMMON FAULTS
ZONE FAULT
DEVICE FAULT
When the FAULT condition has been rectified, the panel can be reset as follows:
Press the SILENCE BUZZER button (the audible buzzer stops, the ZONAL fault,
COMMON FAULT and DEVICE FAULT lights continue flashing).
Enter Access Level 2 code and press (refer to Access to Controls).
When all zone fault conditions have been rectified, press the RESET button.
Press to revert to Access Level 1.
Note: Most fault conditions are self-resetting and will clear without the need to RESET
the control panel. However, a number of fault conditions exist that will require
Engineering Assistance.
If there is any doubt as to the diagnosis of a particular fault, contact your
service provider for assistance.
Figure 12 – LT Control Panel Example FAULT Condition
COMMON FAULTS

7
6 TO ACTIVATE ALL ALARMS FOR EVACUATION
To activate all alarm sounders for evacuation purposes, the procedure below should be
followed (refer to Figures 13, 14 & 15):
Enter Access Level 2 (refer to Access to Controls).
Press the EVACUATE button on the Control Membrane to sound the alarms (the red
ALARM light flashes and the audible sounders operate).
The LCD shows the message EVACUATE.
Figure 13 – Example EVACUATION Condition
Figure 14 – Standard Control Panel Example EVACUATION Condition
GENERAL ALARM
INDICATION
When the evacuation procedure is complete, and the building is safe to be entered, the
alarm can be silenced by following the procedure detailed below.
Press the SILENCE BUZZER button (the audible buzzer stops, the ALARM light
continues to flash). The audible alarm circuits will continue to sound unless
previously isolated.
Enter Access Level 2 (refer Access to Controls).
Press the SILENCE ALARMS button (the audible alarms stop). The red ALARM light
comes on constant.
Press the RESET button.
Press to revert to Access Level 1.
Figure 15 – LT Control Panel Example EVACUATION Condition
ALARM INDICATION

8
Figure 16 – Example ZONE / DEVICE Isolation
Figure 17 – Standard Control Panel Example ZONE / DEVICE Isolation
COMMON ISOLATE
DEVICE ISOLATE
ZONAL ISOLATE
7 ISOLATION OF DETECTION ZONES/DEVICES
To ISOLATE detection ZONE(s) / DEVICE(s) the following procedure must be followed:
Enter Access Level 2 (refer Access to Controls).
Press the “0” button to obtain access to the menus.
Select the ISOLATE option from the menu by using the ARROW buttons and
press .
To ISOLATE detection ZONE(s):
Select the ZONES option from the menu by using the ARROW buttons and press .
Enter the number of the ZONE you wish to isolate and press .
The selected ZONE will be highlighted and can be isolated by pressing .
Further ZONE isolations can be achieved by using the ARROW buttons to move to
the required ZONE and pressing to confirm isolation.
Press to revert to Access Level 1.
Indication that zones are isolated will be provided on the panel as detailed in (refer
Figure 16, 17 & 18):
Figure 18 – LT Control Panel Example ZONE / DEVICE Isolation
DISABLEMENT

9
To ISOLATE detection DEVICE(s):
Select the LOOP DEVICES option from the menu by using the ARROW buttons and
press .
Select the SINGLE DEVICE option from the menu by using the ARROW buttons and
pressing .
Enter the LOOP and DEVICE number for the device you wish to isolate and press .
The selected DEVICE will be highlighted and can be isolated by pressing .
Further DEVICES can be selected for isolation by using the ARROW buttons to select
the device and pressing to confirm selection.
Press button to revert to Access Level 1 once isolations are complete.
DEVICE and ZONE isolations can be removed by following the above procedures and
selecting the DEVICE / ZONE with the button.
8 ISOLATION OF SOUNDERS OR RELAY SHUTDOWNS (Output Groups)
To ISOLATE output group(s) follow the procedure below:
Enter Access Level 2 (refer to Access to Controls).
Press the 0button to obtain access to the menus.
Select the ISOLATE option from the menu by using the ARROW buttons and
press .
Select the OUTPUT GROUPS option from the menu by using the ARROW buttons and
press .
Enter the number of the OUTPUT GROUP to be isolated and press .
The selected OUTPUT GROUP will be highlighted and is isolated by pressing .
Press to revert to Access Level 1.
Figure 19 – Example Output Group Isolation

10
OUTPUT GROUP isolations can be removed by following the above procedures and
selecting the OUTPUT GROUP for DE-ISOLATION with the button.
Figure 20 – Standard Control Panel Example Output Group Isolation
COMMON ISOLATE
FIRE OUTPUT
ISOLATE
DEVICE ISOLATE
SOUNDER FAULT
9 TO TEST THE PANEL LIGHTS AND BUZZER
To test the Control Panels LIGHTS and BUZZER:
Enter Access Level 2 (refer to Access to Controls).
Press the 0button to obtain access to the menus.
Select the PANEL TEST option from the menu by using the ARROW buttons and
press (the Control Panels TEST light flashes during the TEST process).
The Control Panel will operate the BUZZER, LIGHTS and Liquid Crystal Display LCD
during this process.
Press to revert to Access Level 1 to escape from the menu options.
10 MAINTENANCE
This guide only covers maintenance of the Fire Control Panel. For maintenance of
external equipment (detectors, signalling equipment, etc.), refer to the appropriate
Manufacturer’s literature.
10.1 Record all performance checks and maintenance operations in the Maintenance
Record.
10.2 Remove dirt and dust from the panel exterior with a soft brush or a lint cloth.
Stubborn stains can be removed with a lint cloth moistened with white spirit.
Make sure all panel indications are legible.
10.3 Examine the exterior of the panel and enclosure for damage or loose cable
glands and rectify any faults.
10.4 On a regular basis or as directed by your Service Company, carry out a Panel
Lights and Buzzer Test. Notify any defects to your Service Company.
10.5 The stand-by batteries are maintenance free but should be replaced every four
years (Refer to your Service Company for battery replacement).
Figure 21 – LT Control Panel Example Output Group Isolation
OUTPUT ISOLATE
TEST

11
MAINTENANCE RECORD
Date Maintenance Operation Carried out by:

Kidde Fire Protection Services Limited
Thame Park Road, Thame, Oxforshire, OX9 3RT
Tel: [phone] Fax: [phone]
www.kfp.co.uk
TM0058 issue 2.02 © Copyright 2003 Kidde Fire Protection Services Ltd