King gates KPD-NO-WIRE-KG-2 Instruction Manual

Page 1 of 2
WIRELESS KEYPAD - Installation / User Manual
Code: KPD-NO-WIRE-KG-2 Short Version instruction
➢pin-codes are similar: to 1,2,3,4, Bor 6,5,8,6, Aetc, - see above picture
➢three (3) different user pin-codes can be set
➢the Dkey is reserved for the Push Button option- DO NOT PROGRAM THIS BUTTON TO THE MOTOR UNLESS YOU NEED THIS OPTION.
➢no need to delete old code; When entering new code - old code will be deleted
➢you need to go into programing mode first, and then, to program a user pin-code
➢for security reason do not use 1234, 1111, or other simple codes
Programming a user pin-code(s) to the unit
1) press buttons A and B together for 6 seconds until you hear - three consecutive beeps
2) press 1,1,1,1, (the default Master Code), followed by the Dbutton - three consecutive beeps
3) key-in new user pin-code: 4 numbers, followed by one of the button A or B or C - one long beep confirms the code has been stored
4) Try the new pin-code; if ok - One confirmation long beep, (if not successful -consecutive short beeps will be heard, repeat steps 1 - 4)
Programming the keypad to a King motor/ control box / your gate:
In the motor or the control box:
1) press the RAD button- the red RAD indicator become steady on and release the button immediately.
If it starts flashing –wait until it goes off, and repeat it again
2) on the keypad; Key-in the new user pin-code you just enter (Eg:1,2,3,4, B) - red RAD indicator on the control unit flashes
3) key-in the other user pin-code if done - RAD indicator on the control unit flashes
4) repeat for more user pin-codes if need to (A, B, C)
5) wait few seconds until the RAD indicator turned off
Programming the keypad to a KingGates FRED receiver:
1) press the tact switch on the RECIVER shortly - green light turns ON
2) key-in the user pin-code you just enter (Eg:1,2,3,4, B) - Green light OFF
3) repeat section 1 and 2 for more pin-codes if need to (A, B, C)
Setting the keypad as a Push Button:
1) press the RAD button on the motor/ control unit.
as the red RAD indicator turns on –release the button immediately. If it starts flashing –wait until it goes off, and repeat it again
2) press the Dkey on the keypad - the RAD indicator flashes while the code is memorized.
3) wait few seconds until the Red RAD indicator turns off –done
Features:
✓Up to three different user pin-codes
✓Push button optional button
✓Wireless –no wires required
✓Powered by standard AAA batteries, included
✓Specifically designed for the KingGates motors
A
D Button
Optional
PUSH BUTTON
C
B
Before programming the keypad - unit
➢fit in the batteries
➢programming, and check reception, prior to the
mounting of the unit
➢metal surface may reduce the reception range
➢using the unit is by keying 4 numbers followed by
one of the dotted buttons A, or B, or C (see picture
above)
➢technical knowledge needed for programming this
unit

Page 2 of 2
Changing the Programing Code:
IMPORTANT: loosing programming code will block the unit, do not change the programming code unless you are fully understanding the
procedure and you are pencilling it, and keeping it in a safe and secure place
1) press the Aand C buttons together for 6 seconds - Three consecutive beeps
2) key-in the existing programming code (1111 by default) followed by the D key - Three consecutive beeps
3) key-in your new Programming code followed by the Dkey - Three consecutive beeps
4) key-in the new programming code again, followed by the D key - Three consecutive beeps
Mounting the keypad
Programme the unit prior to the installation of it
Do not mount the unit horizontally allowed for Australia
Make sure to have a seal on the back part of the keypad
1) Separate the back part of the unit
Seal around the unit
The UP sign for installation direction
Front part back mounting part
2) Follow the “UP” mark on the back plate; fit it vertically to the wall / post
3) Make sure that the foam -seal is in place
4) Put the keypad back together
www.allegrogateautomation.com.au
KingGates – S.R.L
V i a A. M a li gn a n i , 42 - 33077 S a c il e (PN) ITALY
T e l . [phone] - Fax [phone] E-mail: [e-mail] web: www.king-gates.com
Australia:
Allegro Gate Automation Pty. Ltd.
REPLACING THE BATTERIES
1. Insert a screw-driver into the holes on the side of
the unit to take the black plastic sides out.
2. Open the 4 screws of the front metal part
3. Open the 4 screws on the corners,
4. Replace the batteries and close back the unit