King Motor C3 WRC User manual

Thank you
Thank you for selecting this Kingmotor product! This kit is designed to be fun to drive and uses top quality parts for durability and perfor -
mance. The instruction manual you are reading was designed to be easy to follow yet thorough in its explanations. Kingmotor wants you to
enjoy driving your newR/C kit. Ifyou come across any problems or need some help getting through a step, give us a call and we will do our very
best to help you. You can also contact us on the internet at www.Kingmotor.cn.
This is a high performance R/C kit, and it requires regular maintenance for best performance. If you don’t do regular maintenance the perfo
mance will suffer. Kingmotor has all the necessary parts and accessories available to keep your car performing at its best.
The caution or attention symbols will warn you about steps that can be very dangerous.
Please read and understand the instructions carefully before proceeding.
Failure to follow these instructions can
cause injury to yourself or others.
You might also cause property damage
or damage your kit.
Attention
Cautions
Before Running
While Operating
Before Operating
After Running
Please read manual (with parent, guardian or a responsible adult if necessary).
Please do not run on a public street, this could cause serious accidents, personal injuries and/or property damage.
Please do not run near pedestrians or small children.
Please do not run in small or confined areas.
Make sure that all screws and nuts are properly tightened.
Always use fresh batteries for your transmitter and receiver to avoid losing control of the model.
Please confirm the neutral throttle trigger position.
Turn OFF receiver first, then turn OFF transmitter. This will prevent the car from losing control.
After running Kingmotor product, it is necessary to perform routine maintenance.
Failure to do this can result in increased wear and damage to the engine and chassis.
Pleasebe careful when handling the battery. It will be hot after running. If the wireis frayed, a short circuit cancause a fire.
Battery safety
Thanks For Purchasing Our Products.
警 告
Thank you for choosing our racing products. Designed to be fun with high performance ,high-quality parts. It is very durable and east to control.
We sincerely hope that you will enjoy our products. If you have any questions or suggestions, please feel free to contact us by phone, online tools or
visit our webeite: www.kingmotor.cn for more information.
This car performs very well, but in order to perform at its best, please maintain it regularly. Otherwise, the sense of driving will be
reduced. All the parts and components in good condition will make the car reach the best level.
The signs of warnings and cautions tell you that these steps are dangerous.
Please read this operation manual carefully before operation.
Failure to follow the instructions will
damage the car body.
Warnings
Please read this manual before using。
Your model is not intended for use on publicroads, congested areas,small places where have babies, If do so, the accidents can
be caused , cars damages, hurting people or disrupt pedestrian or vehicular traffic.
. Make sure all screws, all parts are tight。
. Make sure the batteries are of RC in good conditions to avoid the losing control of the car.
. Mare sure the RC frequency match respectively in playing fields.
After using:
. Turn off the receiver, then turn off the RC to avoid the losing control of car.
. Regular maintenance is a “MUST”or will damage the engine and chassis and shorten the life of the car.
Paymoreattentionbatteriestreatment,overheat,wirelessbrokenandshortcircuitcurrentcancausedfireaccidents.
1
Failure to follow these instructions
can damage your kit, and cause
serious bodily injury or death.
Cautions
Failure to follow the instructions
may hurt the car player.
Cautions
Warnings

Overview 产品概要
Components
组成部分
Parts Bag
零件包
Radio control car
遥控车
lncluded ltems 包含⼯具
E816 0
wrench
L型扳⼿
5
mm
4
mm
E8160
Wheel Wrench
17mm轮胎扳⼿
Equipment Needed
需要配件
Brushless ESC
无刷电调
CHARGER
充电器
Do not use NiCd/NiMH battery chargers for LiPO batteries.
4 s(1 4. 8 v) LIPO BATTERYPACK
6 s(2 2.2 v) LIPO BATTERYPACK
4s(14.8v) 锂电池组
6s(22.2v) 锂电池组
Maximum battery dimensions
最大电池尺寸158mm×50mm×60mm
Transmitter
遥控器
2
1.5
mm
2.5
mm
2
mm
3
mm
7
mm
5. 5
mm
or
或
If you do not use a special charger for LiPO batteries, they
Brushless motor
无刷电机
3.0mm
1.5mm
2.5mm
2.0mm
will be damaged.
请勿使用镍镉/镍氢电池充电器来给锂电池充电。请勿使用非
专用充电器对锂电池充电，否则会损坏您的锂电池。
E8160
Cross Wrench
小十字套筒工具

3
CH2: Electronic Speed Controller
CH2: 电⼦调速器(电调)
CH3:
A ttention: The lighting system shall be connected to CH1 and CH2 channels in
parallel according to the instructions of the lighting system manual.
注意：灯组接线按照灯组说明书，将灯组线并联接⼊CH1和CH2通道。
CH3: 4WD/RWD Shifting servo
CH1:四驱后驱切换舵机
Receiver Connection 接收机连接
4 WD/ RWD Shifting servo
四驱/后驱切换舵机
Chassis top view 底盘俯视图
CH1: Steering Servo
CH1:⽅向舵机
B rushless Motor
⽆刷电机
B rushless ESC
⽆刷电调
Battery house
电池仓
Steering servo
⽅向舵机
Brushless Motor
⽆刷电机
Receiver box
接收盒
Receiver
接收机
Switch
电调开关
Battery
电池
CH2:
CH1:

01 ×2
TMS4004
M4×4mm
THP2514
5×14mm
E8085
E8086
TW041003
E8085
TRD10020
TBB081605
E8016
E8086
TBB081605
E8060
TMS4004
E8060
4
TW041003
4×10×0 .3 mm
TRD10020
10×2mm
TBB081605
8×16×5mm
TRD10020
THP2514
E8085
×8
×2
×4
×4
×4
E8083
THP2514
TW041003

前/后
TF3016
M3×16mm
E8090
E8090
FRONT
# 10000cst
前
03 ×4 10 . 5 mm
TMN25
TMN25
TW030705
3×7×0 .5 mm
E8073
E8371
TW030705
TRD21010
D21 ×1mm
E8070
E8305
5
REAR
#5000cst
后
02
TF3016
TRD21010
TF3016
TF3016
TF3016
×8
×4
×4
×4

×4
TRD07519
×4
E8370
E8075
S hocT O il
6
TRD07519
D7 .5×1 .9 mm
TRD12012
D12×1 .2 mm
×8
×4
05
#400cst
04
E8074
E8074
TRD07519
TRD12012
E8372

06 ×4
E8077
E8307
E8074
E8373
E8071
07 左/右
TC4012
M4×12mm
E83
TMS5004
TC4 0 1 2
TMN30
E8003
THP3017
TBB081404
E8004
E8056
TBB081404
E8046
THP3017
TC4012
TMS5004
7
L/ R
TBB081404
N30
×2
×2
×2
×4
×4
TM
74

08 左/右
TF2506
M2 .5×6mm
E8001
E81
E8001
TF2506
09 左/右
TB3006
M3×6mm
TC3020
M3×20mm
TMN30
TMN30
E8050
TB3006
8
L/ R
L/ R
TC3020
TB3006
×12
×2
×2
×4
40

10
×2
E8054
72mm
E8053
9
TMS3003
M3×3mm
TMS3008
M3×8mm
×2
×4
E8013
E8013
E8039
11
E8047
TMS3003
E8052
×2
×2
TMS3003
E8020
E8047
E8020
TMS3008
E8020
E8052
E8020
E8092
TMS3008

12 TW131602
TMS4004
M4 × 4 mm
TB3004
M3×4mm
TW131602
TC3518
M3 .5×18mm
TBB081605
TW131602
TBB081605
8×16×5mm
TB3
TBB081605
TW131602
13×16×0 .2 mm
E8362
TB3 0 0 4
TC3518
13
TC3518
M3 .5×18mm
TC3518
TC3540
M3 .5×40mm
E800 6
E836 3
TC3540
10
TW131602
TMS4004
E8084
E8062
E8006
004
×2
×1
×2
×2
×2
×2
×4

14
TB3014
M3×14mm
E8359
TB3014
15
TB3004
M3×4mm
TMN30
TB3020
M3×20mm
TMN30
E8048
TSP30
TSP30
TB3 0 0 4 E80 4 8
3020
11
TMN30
TB3
P30
020
×2
×2
×2
×2
×4
TS
TB

E8006
TMS3004
TMS3004
E8006
16
TC3012
M3×12mm
TMS3004
M3×4mm
TC3012
TBC2205
M2 .2×5mm
TBC2205
17
TB3020
M3×20mm
TB3 0 2 0 R
M3 × 2 0 mm
E80 5 5
E8410
TC3022
M3×22mm
TMNF30
E8 4 1 0
TMNF3 0
B3020R
TB3
12
TMNF30
TC3022
E8055
020
×2
×2
×2
×1
×1
×2
×4
T

18 E8312
TF3010
M3×10mm
TMN40
TMN40
E8312
E8385
TF3010
19
TB3010
M3×10mm
TB3010
13
×3
×1
×2
E8409

21
26 mm
E8054
E8013
14
TMS3003
M3×3mm
×2
×2
E8053
E8040
86 mm
E8013
20
TMS3003
TMS3003
E8093

TBB081605
E8056
22 左/右
E8002
TF2506
M2 .5×6mm
E8002
TF2506
左/右
L/ R
TMS5004
M5×4mm
TMN30
THP3017
E8005
THP3017
3×17 mm
TBB081605
TBB081605
8×16×5mm
5004
15
L/ R
23
TC3020
M3×20mm
E8140
TC3020
TMN30
E8059
×12
TMS
×2
×2
×2
×2
×4

L/ R
TB3006
M3×6mm
06
25
TW131602
TB3004
M3×4mm
TMS4004
TC3514
M3 .5×14mm
TBB081605
TMS4004
M4×4mm
TW320810
3 .2×8×1mm
E8006
TW32
E8062
TB3004
TBB0 8 1 6 0 5
8 × 1 6 × 5 mm
E83 6 3
TW320810
TB3004
TW131602
13×12×0 .2 mm
16
左/右
24
TBB081605
TC3514
TB3006
TB30
0810
084
×2
×2
×2
×1
×2
×2
×4
E8
E8051
E8005

26
TC3518
M3 .5×18mm
TW131602
TW131602
13×12×0 .2 mm
E8006
TC3518
E8087
TW1
TC3518
27
TB3014
M3×14mm
TB3014
17
E8360
31602
×2
×2
×4

28
TB3004
M3×4mm
TB3020
M3×20mm
TMS3003
M3 × 3 mm
TB3 0 2 0
TMN30
TMN30
E8368
E8364
TW320810
3 .2×8×1mm
TB3020
TC3540
E8368
TW320810
TMS3003
TC3540
M3 .5×40mm
29
TC3012
M3×12mm
TMS3005
M3 × 5 mm
TC3012
TMS3005
TBC2205
18
TBC2205
M2 .2×5mm
TB3004
TMN30
E8049
3003
TMS
×2
×2
×2
×2
×2
×2
×2
×2
×4
E8006
TMS3005
E8006
E8049
TW320810