KingShield OD103 User manual

‘Orion Range’
In ra-red Motion Sensor - IP65
Model: OD103
Detectio from Above
Poor Se sitivity
FIELD OF DETECTION
Importa t Safety I structio s
• Pl as r ad th s instructions car fully b for installation and k p saf for futur r f r nc .
IMPORTANT
This product should b install d by a comp t nt p rson and in accordanc with th curr nt
IET Wiring R gulations and Building R gulations.
If in doubt,consult a qualified electrician.
• Always turn off th mains supply b for comm ncing work.
As th d t ctor r sponds to chang s in t mp ratur , avoid th following situations:-
• Avoid pointing th d t ctor towards obj cts with highly r fl ctiv surfac s, such as mirrors
tc.
• Avoid mounting th d t ctor n ar h at sourc s, such as h ating v nts, air conditioning
units, lights tc.
• Avoid pointing th d t ctor towards obj cts that may mov in th wind, such as curtains,
tall plants tc.
Switch the mai s supply OFF first to preve t electric shock.
INSTALLATION
Good Se sitivity
This product uss an infra-rd hat dt ctor. Th dt ctor snss ‘warmth mov m nt’ in th
surrounding ar a wh n it is dark. Wh n mov m nt is d t ct d th s nsor is activat d and
triggrs th connct d load. It has a built in photo-c ll that can id ntify day and night.
1. R mov th r ar cov r by r moving th
scr w and pulling off cov r, r f r to Dia:1.
2. Conn ct th mains in and load out
cabl according to Dia: 2f ding cabl
through th silicon gromm t.
Dia:1Dia:2
OD103 Ins .qxp_GU10 20/11/2015 13:16 Page 1

Issu No: 704278
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
in [email protected]
www.greenbrook.co.uk
4. Position s nsor onto back plat and s cur using th scr w r mov d in st p 1.
1. Turn ‘Tim ’ control fully anti-clockwis and
‘Lux’ control fully clock wis r f r to Dia: 4.
2. R -conn ct mains supply, allow 30 s conds
for th s nsor to warm-up, and th n
p rform a walk-by in front of th s nsor;
lamp should turn on and stay on for
approximat ly 10 s conds, and will go off if
no furth r mov m nt is d t ct d.
TESTING
ADJUSTING THE ‘LUX’ CONTROL
1. Turning Lux control fully clock wis , th s nsor will op rat in both daylight and darkn ss.
2. Turning Lux control fully anti-clockwis , th s nsor will op rat in darkn ss only.
3. S t control to op rat at your r quir d daylight l v l.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning th tim control fully anti-clock wis will s t th on duration to 10 s conds +/- 3
s conds.
2. Turning th tim control fully clock wis will s t th on duration to 15 minut s +/- 2minut s.
TROUBLE SHOOTING
Light ot comi g o
• Ch ck that lamp is good.
• Ch ck th r is nothing obscuring th PIR s nsor.
I termitte t operatio
• Ch ck th r ar no curtains that can mov in th wind.
• Ch ck th r ar no h ating v nts n arby.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
TECHNICAL INFORMATION
Rat d Voltag : 230V～50Hz
IP Rating: IP65
Ambi nt Light: <3-2,000 LUX (Adj)
Tim D lay: Min 10 s c ± 3s c
Max 15 min ± 2min
Rat d Load: Max 1200W
Max 300W
D t ction Rang : 180°
D t ction Distanc : 12M max (<24°C)
Working T mp: -20° - + 40°C
Working Humidity: <93%RH
Pow r Consumption: 0.5W approx
Installation H ight: 1.8 - 2.5M
D t ction Moving Sp d: 0.6 - 1.5m/s
Dia:4
Dia:3
3. S cur th s nsor back plat to th wall using
two wood scr ws ( nsur th r is no
wiring/gas/wat r s rvic s dir ctly b hind th
scr ws) Dia:3.
/LED
OD103 Ins .qxp_GU10 20/11/2015 13:16 Page 2