KingShield Orion OD102 User manual

‘Orion Ran e’
Infra-red Motion Sensor - Ceilin Mounted
Model: OD102
Detectio from
Above Poor Se sitivity
FIELD OF DETECTION
Importa t Safety I structio s
• Please read these instru tions arefully before installation and keep safe for future
referen e.
IMPORTANT
This produ t should be installed by a ompetent person and in a ordan e with
the urrent IET Wiring Regulations and Building Regulations.
If in doubt,consult a qualified electrician.
• Always turn off the mains supply before ommen ing work.
As the dete tor responds to hanges in temperature, avoid the following situations:-
• Avoid pointing the dete tor towards obje ts with highly refle tive surfa es, su h
as mirrors et .
• Avoid mounting the dete tor near heat sour es, su h as heating vents, air
onditioning units, lights et .
• Avoid pointing the dete tor towards obje ts that may move in the wind, su h as
urtains, tall plants et .
Dia:1
1. Remove the over by rotating anti- lo k wise.
Switch the mai s supply OFF first to preve t electric shock.
INSTALLATION
Good Se sitivity
2. Conne t the mains in and load out wires a ording to Dia:1.
N = Neutral ‘IN’
L = Live ‘IN’
A = Output to Load
This produt uses an infra-red heat dete tor. The dete tor senses ‘warmth movement’ in the
surrounding area when it is dark. When movement is dete ted the sensor is a tivated and
triggers the onne ted load. It has a built in photo- ell that an identify day and night.
OD102 Ins.qxp_GU10 20/11/2015 13:42 Page 1

Issue No: 704277
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
info@ reenbrook.co.uk
www. reenbrook.co.uk
Dia:3
TESTING
ADJUSTING THE ‘LUX’ CONTROL
1. Turning Lux ontrol fully lo k wise, the sensor will operate in both daylight and
darkness.
2. Turning Lux ontrol fully anti- lo kwise, the sensor will operate in darkness only.
3. Set ontrol to operate at your required daylight level.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning the time ontrol fully anti- lo k wise will set the on duration to 10 se onds
+/- 3se onds.
2. Turning the time ontrol fully lo k wise will set the on duration to 15 minutes +/- 2
minutes.
Repla e over by positioning over and rotating lo kwise.
TROUBLE SHOOTING
Light ot comi g o
• Che k that lamp is good.
• Che k there is nothing obs uring the PIR sensor.
I termitte t operatio
• Che k there are no urtains that an move in the wind.
• Che k there are no heating vents nearby.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
TECHNICAL INFORMATION
Rated Voltage: 230V～50Hz
IP Rating: IP20
Ambient Light: <3-2,000 LUX (Adj)
Time Delay: Min 10 se ± 3se
Max 15 min ± 2min
Rated Load: Max 1200W
Max 300W
Dete tion Range: 360°
Dete tion Distan e: 6M max (<24°C)
Working Temp: -20° - + 40°C
Working Humidity: <93%RH
Power Consumption: 0.5W approx
Installation Height: 2.2 - 4M
Dete tion Moving Speed: 0.6 - 1.5m/s
Dia:2
1. Turn ‘Time’ ontrol fully anti- lo kwise
and ‘Lux’ ontrol fully lo k wise, refer
to Dia: 3.
2. Re- onne t mains supply, allow 30 se onds for the sensor to warm-up, and then
perform a walk-by in front of the sensor; lamp should turn on and stay on for
approximately 10 se onds, and will go off if no further movement is dete ted.
3. Se ure the sensor ba k plate to the wall using
two wood s rews (ensure there is no
wiring/gas/water servi es dire tly behind the
s rews) Dia:2.
/LED
OD102 Ins.qxp_GU10 20/11/2015 13:42 Page 2