KingShield Orion Range OD101 User manual

‘Orion Ran e’
Infra-red Motion Sensor - Ceilin Slimline
Model: OD101
Detectio from
Above Poor Se sitivity
FIELD OF DETECTION
Importa t Safety I structio s
• Please rea these instructions carefully before installation an keep safe for future
reference.
IMPORTANT
This pro uct shoul be installe by a competent person an in accor ance with
the current IET Wiring Regulations an Buil ing Regulations.
If in doubt,consult a qualified electrician.
• Always turn off the mains supply before commencing work.
As the etector respon s to changes in temperature, avoi the following situations:-
• Avoi pointing the etector towar s objects with highly reflective surfaces, such
as mirrors etc.
• Avoi mounting the etector near heat sources, such as heating vents, air
con itioning units, lights etc.
• Avoi pointing the etector towar s objects that may move in the win , such as
curtains, tall plants etc.
1. Remove the cover by rotating anti-clock wise.
Switch the mai s supply OFF first to preve t electric shock.
INSTALLATION
Good Se sitivity
2. Connect the mains in an loa out wires accor ing to Dia: 3, using the rear
entry or si e entry knock-outs as require see Dia:1an 2.
This pro uct uses an infra-re heat etector. The etector senses ‘warmth movement’ in the
surrouning area when it is ark. When movement is etecte the sensor is activate an
triggers the connecte loa . It has a built in photo-cell that can ientify ay an night.
Si e-entry KnockoutsRear-entry Knockouts
Dia:1Dia:2
OD101 Ins.qxp_GU10 20/11/2015 13:52 Page 1

Issue No: 704276
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
info@ reenbrook.co.uk
www. reenbrook.co.uk
Dia:5
TESTING
ADJUSTING THE ‘LUX’ CONTROL
1. Turning Lux control fully clock wise, the sensor will operate in both aylight an
arkness.
2. Turning Lux control fully anti-clockwise, the sensor will operate in arkness only.
3. Set control to operate at your require aylight level.
ADJUSTING THE ‘TIME ON’ CONTROL
1. Turning the time control fully anti-clock wise will set the on uration to 10 secon s
+/- 3secon s.
2. Turning the time control fully clock wise will set the on uration to 15 minutes +/- 2
minutes.
3. Set control to your require time setting.
TROUBLE SHOOTING
Light ot comi g o
• Check that lamp is goo .
• Check there is nothing obscuring the PIR sensor.
I termitte t operatio
• Check there are no curtains that can move in the win .
• Check there are no heating vents nearby.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
1. Turn ‘Time’ control fully anti-clockwise
an ‘Lux’ control fully clock wise, refer
to Dia: 5.
Dia:3
3. Secure the sensor to the ceiling using two woo screws (ensure there is no
wiring/gas/water services irectly behin the screws) refer to Dia:4.
Dia:4
2. Re-connect mains supply, allow 30 secon s for the sensor to warm-up, an then
perform a walk-by in front of the sensor; lamp shoul turn on an stay on for
approximately 10 secon s, an will go off if no further movement is etecte .
TECHNICAL INFORMATION
Rate Voltage: 230V～50Hz
IP Rating: IP20
Ambient Light: <3-2,000 LUX (A j)
Time Delay: Min 10 sec ± 3sec
Max 15 min ± 2min
Rate Loa : Max 2000W
Max 1000W
Detection Range: 360°
Detection Distance: 6M max (<24°C)
Working Temp: -20° - + 40°C
Working Humi ity: <93%RH
Power Consumption: 0.5W approx
Installation Height: 2.2 - 4M
Detection Moving Spee : 0.6 - 1.5m/s
/LED
OD101 Ins.qxp_GU10 20/11/2015 13:52 Page 2