Kingtop S600 User manual

User guide
POS terminal S600
Manual Version: V1.0

Copyrights © 2023 Kingtop Corp. All rights reserved. The information contained in this document is
subject to change without notice and should not be construed as a commitment by Kingtop Corp.
Patents and Licenses
For a complete list of all Kingtop Corp. patents, visit https://www.kingtoptec.com/contact
Software License
Proprietary Rights Provisions:
The software drivers provided with this product are copyrighted by Kingtop Corp. and/or
Kingtop Corp.’ suppliers. Although copyrighted, the software drivers are unpublished and
embody valuable trade secrets proprietary to Kingtop Corp. and/or Kingtop Corp.
suppliers. The disassembly, decompilation, and/or Reverse Engineering of the software
drivers for any purpose is strictly prohibited by international law. The copying of the
software drivers, except for a reasonable number of back-up copies is strictly prohibited
by international law. It is forbidden by international law to provide access to the software
drivers to any person for any purpose other than processing the internal data for the
intended use of the software drivers.
Trademarks and Service Marks
Kingtop Corp. is a trademark of Kingtop Corp., and the other trademarks, logos, and
service marks (collectively the “Trademarks”) used in this user manual are the property of
Kingtop Corp. or their respective owners. Nothing contained in this user manual should
be construed as granting by implication, estoppel, or otherwise, a license or right of use of
Kingtop Corp. or any other Trademark displayed in this user manual without the written
permission of Kingtop Corp. or its respective owners.
• Kingtop Corp., and the Kingtop Corp. logo are all trademarks of Kingtop Corp.
The names of actual companies and products mentioned in this user manual may be the
trademarks of their respective owners.

Contents
1. About Your POS Terminal .............................................................................. - 1 -
Front view ....................................................................................................- 1 -
Back view .................................................................................................... - 2 -
2. Operating Instructions ................................................................................... - 2 -
Turning your POS terminal on/off ................................................................ - 2 -
Magnetic stripe card ....................................................................................- 3 -
Contact IC card ........................................................................................... - 3 -
Contactless IC card .....................................................................................- 4 -
Install the printer paper ............................................................................... - 4 -
Tear paper ................................................................................................... - 5 -
Install the SIM/PSAM card .......................................................................... - 5 -
Insert the battery ......................................................................................... - 6 -
Charge your device ..................................................................................... - 7 -
3. Precautions ................................................................................................... - 7 -
Safety Warning ............................................................................................- 7 -
Important safety instructions ....................................................................... - 8 -
Suggestions ................................................................................................ - 8 -
Declaration .................................................................................................. - 8 -
Disclaimer ................................................................................................... - 9 -
4. Proper Battery Use and Disposal .................................................................. - 9 -
5. Limited Warranty and liability .......................................................................- 10 -

- 1 -
1. About Your POS Terminal
Front view
❶NFC reader —— For Proximity card, membership card
❷Paper silo cover—— Protecting and Cutting Thermal Paper
❸Volume buttons —— Adjust the volume level
❹Front camera—— Supports photographing and 1D/2D code quick scanning.
❺Power on/off button——
Short press: wake up the screen, lock the screen.
Long press: long press for 2-3 seconds in power off mode to switch on the device.
Long press for 2-3 seconds in normal operation mode to select power off or reboot.
Long press for 11 seconds when system is frozen for automatic reboot.
❻Light sensor—— Automatically adjusts the two degrees of the display
❼MSR card reader——Used for reading the information stored in the magnetic stripe of
bank card.
❽Display screen —— Used to display product information and other functions
❾ICCR Card reader —— Used for inserting the bank chip card.

- 2 -
Back view
❶Label/Sticker —— For custom logos and labels
❷Rear camera—— Supports photographing and 1D/2D code quick scanning.
❸Type-C USB —— Used for charging equipment and debugging by developers.
❹Pogo pin—— Use as a charging function
❺MIC—— Support for recording external voices
❻Battery cover—— It can be disassembled, battery can be replaced
❼Audio port—— External headphones are available
❽Speaker —— Broadcast payment status
2. Operating Instructions
Turning your POS terminal on/off
Power on: Press the "heart" button on the left side of the POS machine for 2-3 seconds,
and the POS machine will start booting
Power off: Press and hold the "heart" key in the power on state, the screen displays
"shutdown, restart airplane mode, silent mode", select "shutdown", and "Your smart
terminal will shut down, 【Cancel】and【OK】Picture，At this point, press the【OK】
key to complete the shutdown.

- 3 -
Magnetic stripe card
When you swipe the card, please slide the magnetic stripe of the magnetic card towards the
inside of the device and across the magnetic track (as shown in the figure), the process
should be smooth and at an even speed.
Magnetic stripe facing the inside of the device
[Note]
If the track of the magnetic stripe card is damaged or the card is swiped incorrectly, the
transaction may fail.
Contact IC card
The IC card slot is located on the right side of the machine. When inserting the card, hold
the IC card without the end of the chip, the chip side is facing up, insert the IC card into the
card slot and push it to the end. The IC should be kept stuck in the card slot throughout the
transaction. As shown in the picture :
[Note]
If the chip contacts of the IC card are damaged or oxidized, the transaction may fail.
Chip card facing inside the device

- 4 -
Contactless IC card
When you swipe the card, please put the IC card close to the center of the screen and stay
for about 1s. When you hear a "beep", it indicates that the card is swiped successfully, and
you can remove the card. As shown in the picture:
IC card near the center of the NFC reader
Install the printer paper
❶Step1. Buckle the edge of the paper compartment cover, and open the paper
compartment cover in the direction shown.
❷Step2. Peel off the printing paper, pull one end of the printing paper, align the paper
compartment in the direction shown in the figure, and leave a small section of paper above
the paper cutter
❸Step3. Close the paper compartment cover in the direction shown in the illustration.
❶Open the paper cover ❷Put the thermal paper ❸Close the paper cover

- 5 -
[Note]
When loading thermal paper, please pay attention to the direction of the paper, and follow
the instructions in the illustration to turn the paper roll open side down, otherwise
characters cannot be printed.
Tear paper
Pinch the protruding part of the print paper with your hand and tear the paper in the
direction shown in the illustration(downwards). Try to keep the force even and fast during
the paper cutting process.
Tear Paper Down
Install the SIM/PSAM card
Step1: Power off and open the battery cover
Step2:After removing the battery, put the SIM/PSAM card into the card slot (the chip side
faces the inside of the machine) . As shown in the picture:

- 6 -
NO.
Description
NO.
Description
❶
SIM1 Card Slot
❸
TF Card Slot
❷
SIM2/SAM2 Card Slot
❹
SAM1 Card Slot
[Note]
1. To install or remove the SIM/PSAM card, please ensure that the machine is turned off,
otherwise the card may be damaged.
2. The SIM/PSAM card cannot be pasted with glue, stickers and other media that affect the
thickness of the card, so as not to be able to smoothly load or remove the card.
Insert the battery
Step1: Open the battery cover
Step2: Insert the battery into the battery compartment (the battery gripper faces the rear of
the machine).

- 7 -
Battery gripper faces the rear of the machine
Charge your device
Open the battery cover, put the rechargeable battery into the battery compartment, and
close the battery cover. Connect the USB cable to the adapter or mobile power bank or PC.
Type-C end is inserted into the port on the left side of the machine, and the adapter is
plugged into the power outlet, after the power is turned on, the machine screen shows the
charging progress, and the battery is fully charged 。
3. Precautions
Safety Warning
Please insert the AC plug into the AC outlet corresponding to the marked input on the
accessory power adapter
This is a Class A product. In living environments, this product may cause radio
interference.
In this case, the user may be required to take practical measures against interference.
-Use only the battery supplied with the unit.
-Do not replace the battery when explosive gases are present.
-Do not charge in hazardous locations.