Kinivo 2AEUVKINIVOURBN User manual

Kinivo Urbn
Bluetooth headset
User’s manual
FCC ID: 2AEUVKINIVOURBN

Contents
Brief introduction…………...…………………………..…..................1
Before use………………………………………………..............……..1
1. Overview…………………………………………………................……1
2. Charging the Headsets…………………………………………..........…2
Getting started……..……………………………………..............……2
1. Turning on/off the headsets………………………………...........….......3
2. Pairing headsets with Bluetooth devices…………………......……..….3
1) How to enter pairing mode………………….……........…………….3
2) Pairing headset with a Bluetooth cell phone via Bluetooth……......4
3) Pairing headset with a Bluetooth cell phone via NFC.......................4
4) Pairing headset with a Bluetooth transmitter via Bluetooth…........5
5) Pairing headset with Multi-devices via Bluetooth…………....…….6
3. Battery display...…………………………………………........……....6
4. Making calls with the headset…………………………….........……….7
5. Music playback………………………............……………………..…..9
6. LED indicator……………………………............……………………..11
7. Factory Reset………………………………............………………..….11
Care and maintenance……………………...............………..………..12
FAQs……………………………………...……...............……………..12
Specification……………………………...………..............………..…13

Welcome to use this Bluetooth headset, Kinivo Urbn. Please read this user’s
manual carefully before use.
Brief introduction
1. About Kinivo Urbn
Kinivo Urbn is a Bluetooth headset.
1. Foldable and retractable design is very easy to take with you. You can
enjoy music wirelessly by using Kinivo Urbn.
2. It Supporting NFC (Near Field Communication) function, it can quickly
connect with Bluetooth cell phone supporting NFC function.
3. It supporting call and music function simultaneously. You will
never miss a call when enjoying music.
Before use
1. Overview
1

1
Left speaker
8
Charging jack
2
Right speaker
8
LED indicator
3
Retractable design
10
▲button
4
NFC zone
11
5
Volume up
12
▼button
6
Volume down
13
Microphone
7
Slide switch
14
AUX-in jack
2. Charging the headset
When the headset is low power, the headset emits once every 5 minutes and
the red LED flashes. Please recharge the battery of the headset.
The way of charging as following:
Using USB cable
1. Plug USB charging cable into the USB
port of computer
2. Plug another side of USB cable to the
headset
Red light on: Charging
Red light off: Finish charging
3. It will takes about 3 hours to finish
charging
Remarks:
1) The battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
2

Getting started
1. Turning on/off the headset
Functions
Operation
LED
indicator
Prompt tone
Turning on
Toggle the slide
switch to ON
Blue Led
flashes for
1 second
Four rise tone
Turning off
Toggle the slide
switch to OFF
Red Led
flashes for
1 second
Four fall tone
Remark: In order to save power, the headset will turn off automatically if
no devices can be connected after 5 minutes.
2. Pairing the headset with Bluetooth devices
1) How to enter pairing mode
Functions
Operation
LED
indicator
Prompt
tone
Enter
pairing
mode
Ensure the headset is on,
and then press and hold
button for 5 seconds
Red and
blue Led
flashes
alternately
Two rise
tone
Remark:
Pairing mode will last 2 minutes. If no devices can be connected after 2
minutes, it will return to standby mode automatically.
In standby mode(not connected and connected), long press button to enter
pairing mode.
3

2) Pairing the headset with a Bluetooth cell phone via Bluetooth
Prior to using the headset for the first time, you have to pair it with a
Bluetooth-enabled cell phone. The pairing procedures are subject to
different models of cell phones. Please refer to your cell phone user’s
manual for further information. The general pairing procedures are as
follows:
1) Keep your headset and phone within 1 meter when pairing;
2) Press MFB button for 6 seconds and release it until red LED and blue
LED flashes alternately. Then your cell phone enter paring mode.
3) Activate your cell phone’s Bluetooth function and set your cell phone to
search for Bluetooth devices within range, and select “Kinivo Urbn”
from the list of devices shown; After successful connecting, the headset
emits one short tone and blue LED flashes twice every 4 seconds.
Remarks:
According to the indication, enter password PIN No: “0000”
After pairing is successful, the headset and the cell phone will remember
each other, they will no need to re-pair next time. The headset will
automatically connect the last device after turn on again.
Every time the headset is turned on, not connected, press button , it
will connect to last connected device automatically.
If the headset and the device out of the effective range and not connected,
it will automatically connect after back to effective range in 10 minutes.
If out of time, short press button to connect.
3) Pairing headset with a Bluetooth cell phone via NFC
If your cell phone support NFC function. Please active the NFC function
and turn on the headset. Use the NFC zone of cell phone to touch the NFC
zone of Kinivo Urbn , the headset will connect with cell phone.
Remarks:
When the cell phone is in sleep or lock screen status, you can’t active
NFC function to connect.
Prior to pairing the headset for the first time, you need use your cell
phone to touch the NFC area until enter pairing mode.
When active the NFC function, try to make the cell phone and the
headset keep touch for longer. Otherwise it may fail to pair.
When the headset is disconnect (in standby mode), you can active NFC
function to fast connect. If the headset has connect, use your cell phone
to touch NFC zone, it will disconnect automatically.
4

4) Pairing the headset with a Bluetooth transmitter via Bluetooth
You can connect the headset to a Bluetooth transmitter to enjoy music
wirelessly. Hereby take BTT005 (Bluetooth transmitter, not included in
accessories) for example. The pairing steps are as follows:
1) Keep your headset and transmitter within
1 meter when pairing;
2) Make the headset enter pairing mode
(Please refer to “How to enter pairing
mode);
3) Turn on the Bluetooth transmitter and
make it enter paring mode. It will search
for Bluetooth devices automatically and send a pairing request;
4) When the headset requests to enter a PIN No., the transmitter will
response “0000” automatically;
5) After successful pairing and connecting, blue LED of the headset flashes
twice every 4 seconds.
Remarks:
The pairing password of Kinivo Urbn is “0000”. So, the headset can only
pair with a Bluetooth transmitter whose pairing password is “0000”.
If pairing still fails after several tries, please refer to the Bluetooth
transmitter’s user’s manual for further information.
5

5) Pairing headsets with Multi-devices via Bluetooth
The headset can connect with two Bluetooth devices at most. If you want to
finish the multi-pairing, please refer to the following steps:
1) Firstly, pair and connect the headset with Bluetooth device one (refer to
“pairing the headset with a Bluetooth cell phone);
2) Long press button and make it enter paring mode again, pair and
connect with Bluetooth device two(refer to “pairing the headset with a
Bluetooth cell phone);
3) Operate Bluetooth device one to connect with headset. The headset has
already connected with Bluetooth device one and two, the headset also
can connect with these two devices automatically after turn on next time.
Remarks:
The steps of turn on/off the multi-pair function as follows:
Turn off multi-pair function: the headset in standby mode, not connect
with device, press MFB and volume down button for 4 seconds
simultaneously and release it until hear a prompt tone.
Turn on multi-pair function: the headset in standby mode, not connect
with device, press MFB and volume up button for 4 seconds
simultaneously and release it until hear a prompt tone.
To improve the stabilization of headset, we suggest you turn off the
multi-pair function when you only connect with one cell phone.
3. Battery display
When the headset connected with IOS device, it will display the battery of
the headset on the device. When the headset is in low battery, power symbol
show red, it emits you to charge for your headset.
6

4. Making a call with the headset
1) Basic operation
Functions
Status of headset
Operation
Cancel a call
Calling
Short press button once
Answer a call
Incoming ringing
Short press button once
Reject a call
Incoming ringing
Long press button for 2
seconds
End a call
During a call
Short press button once
Volume up
During a call
Short or long press button
once
Volume down
During a call
Short or long press button
once
Transfer
conversation to
mobile phone
During a call
Long press button for 2
seconds
Transfer
conversation to
headset
During a call
Long press button for 2
seconds
7

Microphone
mute
During a call
Long press button for 2
seconds
Cancel mute
During a call
(microphone
mute)
Long press button for 2
seconds
Voice dial
Standby mode
(connected
device)
Double click button
2) Three-ways call operation
Functions
Status of headsets
Operation
Answer new call and
end current call
There are second
incoming call
Short press button
once
Answer new call and
retain current call
There are second
incoming call
Double click
button
Switch calls
Keep conversation
Double click
button
End current call and
switch retain call
Keep conversation
Short press button
once
Warning: Excessive pressure from earphones and headphones can
cause hearing loss.
Note:
Not all the mobile phones support all the functions listed above. Please
refer to your mobile phone user’s manual.
Different function and prompt tone according to different mobile phone.
When the volume is adjusted to max or min, you will hear one prompt
tone. When the microphone is mute, it will emits two ”du”every 10
seconds.
When pressing the answer button on some mobile phones, the call will be
transferred to the mobile phone, like iPhone. You can switch the call to
the headset by using the conversation switch button or through operating
on the mobile phone.
8

3) Connecting with two cell phones to make a call
Functions
Status of headset
Operation
End phone call #1
and answer phone
call #2
During phone call #1,
phone 2 has incoming
call
Short press button
once
Retain phone call #1
and answer phone
call #2
During phone call #1,
phone 2 has incoming
call
Double click button
Switch call
During call, one of
phone call is retained
Double click button
End current call,
back to retain phone
call
During call, one of
phone call is retained
Short press button
once
5. Playing music
1) Bluetooth audio mode
When the headset connects to a mobile phone or Bluetooth transmitter
which supportsA2DP, you can enjoy music wirelessly through the headset.
Functions
Status of
headset
Operation
Volume up
Playing music
Short press, long press or press
button continuously
Volume
down
Playing music
Short press, long press or press
button continuously
Last track
Playing music
Short press button once
Next track
Playing music
Short press button once
Microphon
e mute
During a call
Long press button for 2 seconds
Cancel
mute
During a call
(microphone
mute)
Long press button for 2 seconds
Voice dial
Standby mode
(connected
device)
Double click button
Pause
Playing music
Short press button once
Play
Pausing
Short press button once
9

Notes:
When the volume is adjusted to max or min., you will hear one prompt
tone.
If you want to remote control last/next song, pause/play, it needs your
Bluetooth mobile phone or Bluetooth transmitter paired with the headset
to support AVRCP profile, please refer to the user’s manual of your
mobile phone or Bluetooth transmitter for further information.
2) Aux in audio mode
The headset support Aux in audio mode, as shown below, in standby mode,
use a 3.5 to 3.5 audio line to connect the headset and media player. Then you
can enjoy music by wire.
Remark:
When plug in 3.5 audio line, the headset will turn off and Bluetooth will
disconnect automatically, Aux in audio connect is effective
If you want to active Bluetooth function, please pull out 3.5 audio line, and
then turn on the headset to connect.
10

3) USB audio mode
You can enjoy music in computer. The headset can connect to computer by
USB connect
6. LED indicator
LED indicator
Status of headset
Red and blue LED flashes
alternately
Pairing mode
Blue LED flashes once quickly
every 2 seconds
Not connect device
Blue LED flashes twice quickly
every 4 seconds
Have already connected device
Red LED flashes instead of blue
LED
Low battery
7. Factory Reset
In standby mode, long press volum up and volum down button for 8 seconds
and release it until the red and blue LED on simultaneously.
Remarks:
After factory reset, the paired list of headset will be deleted. When you
turn on the headset again, it will enter paired mode automatically, but it
won’t connect with device automatically, you should re-pair and connect
with devices.
In standby mode, you can delete the paired list.
11

Care and maintenance
Read the following recommendations carefully before using Kinivo Urbn.
Following these you will be able to enjoy this product for many years.
Keep it dry and don’t put it in the dump place to avoid the product’s
internal circuit being affected.
Keep the product away from direct sunlight or hot places. High
temperatures will shorten the life of electronic devices, destroy the
battery or distort certain plastic parts.
Don’t use this product during sport to avoid the sweat into product so
that damage the product. This product is not water-resistant.
Don’t expose the product to cold areas. It may damage the internal circuit
board.
Don’t try to disassemble the product as it may get damaged if you are not
professional.
Don’t let it fall down onto the floor or other hard surfaces. The internal
circuit might get damaged.
Don’t use intensive chemical products or detergent to clean the product.
Don’t scratch the surface with sharp things.
In case the product doesn’t function properly, send it to the store you bought
it. The staff will help you to solve the problem
FAQs
1. What does it mean if all the LED indicator turns red?
Battery is low power, need to be recharged.
2. Why is the red LED off when charging?
a) Please make sure the charging device connect with headset Well;
b) You didn’t use the headset for a long time, the battery may dry up. At this
time, you have to charge the battery for 30 minutes, and then the red
LED will be ON.
3. How far is the effective range between the headset and mobile
phone?
According to the Bluetooth standard, the max available range of Class II
headset is 10 meters. It varies under different environment.
12

4. Why my mobile phone can not search and find the headset?
The mobile phone will not find the headset if headset and mobile phone are
not under the pairing mode. Make sure the headset is under the pairing mode
and in the effective working range, and then the headset can be paired and
connected.
5. Why the headset can not hear the voice?
a) Make sure the headset has been switched on;
b) Make sure the volume is not too low or muted;
c) Make sure the headset connects with the mobile phone correctly;
d) Make sure the distance between the headset and the cell phone is in the
available Bluetooth range.
6. Why the headset can not hear the voice clearly in conversation?
a) Make sure the mobile phone is in the strong signal area;
b) Make sure the headset is in the available range of this product.
7. Why can’t control pause, play, last song and next song when playing
music?
This function needs your Bluetooth device supports AVRCP (Audio/Video
Remote Control profile)
Specifications
Bluetooth version
Bluetooth V4.1
Bluetooth profiles
HFP, HSP, A2DP and AVRCP
Operating distance
10 meters
Headset music time
About 17 hours
Headset standby time
Approx 800 hours
Charging input
DC5.0V 500mA
Headset charging time
About 3 hours
Dimension
176*165*32mm
Weight
Approx 180g
Battery capacity
430mAH
13

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following tow conditions:
(1)this device may not cause interference, and(2) this device must
accept any interference, includinginterference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables auxappareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes :(1) l'appareil ne doit
pas produire de brouillage, et(2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre lefonctionnement.

Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.