Kino Flo Kamio 6E User manual

Operation Manual
Kamio Model
KAM-6E
Part No. 3100031 Rev B 01-07-2008
®

2
KIT-KAM6E
Kamio 6E Kit (On-Camera/ ENG w/ Travel Case)
Kit Contents:
1 Kamio 6E Ring-Light (112mm) w/ 3ft Harness
1 Kamio 12VDC On-Camera Ballast
1 Ballast Mount
1 Baby Pin Shoe Mount
1 Travel Case
Dimensions Weight
21 x 7.5 x 17” 10lbs
(53.5 x 19 x 43cm) (4.5kg)
The Kamio 6E is a ring-lite that clips onto the lens of film or video cameras and is
powered by an on-board 12VDC dimming ballast (BAL-149X).
Main application is for a front-fill beauty light for ENG stand-up interviews.
KIT-KAM6E-B
Kamio 6E Kit (On-Camera/ ENG w/ Soft Case)
Kit Contents:
1 Kamio 6E Ring-Light (112mm) w/ 3ft Harness
1 Kamio 12VDC On-Camera Ballast
1 Ballast Mount
1 Baby Pin Shoe Mount
1 Soft Case
Dimensions Weight
19 x 8.5 x 13” 9.5lbs
(48.5 x 21.5 x 33cm) (4.3kg)

3
SYS-KAM6E
Kamio 6E System (On-Camera/ ENG)
System Contents:
1 Kamio 6E Ring-Light (112mm) w/ 3ft Harness
1 Kamio 12VDC On-Camera Ballast
1 Ballast Mount
1 Baby Pin Shoe Mount

4

5
Note:The Kamio is only recommended for fixed barrel lenses. Fixed barrel
lenses are designed to support the weight of the Kamio and keep the fixture properly
oriented.
The Kamio 6E Ring Light is designed to mount directly to the camera lens.
An expandable clamping ring is designed to fit lenses with an outside
diameter of 112mm. Turn the locking screw to clamp down on the lens.
Lens adapter rings are available to accommodate various smaller lens
diameters. (See “Accessories” for details)
(OPTIONAL)

6
Ballast Operation
The Kamio Ballast (BAL-149X) operates remote from the fixture. Connect the
Kamio lamp harness to the extension cable or the Ballast, making sure to rotate
the locking ring until it clicks into the locked position. After the lamps are properly
installed, the Ballast can be turned on. Avoid operating in temperatures above
125°F (51°C).
(Note: The dimmer should be full up when striking the lamp. Once the lamp has
come up to full temperature, in 3-5 minutes, then dim to the desired light level.)
It is normal for the lamp to take 1-2 seconds to ignite. In cold temperatures the
Ballast may take longer to ignite the lamp. If it does not ignite within 5 seconds,
switch the ballast to OFF, and try again. If lamp does not strike after 2 or 3
attempts, turn Ballast off, check that the harness or any extension connections
are secure and restrike.
CAUTION: For AC operation use the PWS-153X or PWS-137X universal power
supply. Do Not operate Camera and Kamio off a Camera Battery Charger.
The combined load exceeds the Charger’s capacity and will result in the
Charger failing.
Changing Lamps
Extract the lamp by pushing the lamp
harness through the reflector. The lamp
will clear the reflector making it easier to
grasp.
To Ensure Proper Operation
ALWAYS TURN OFF THE BALLAST BEFORE connecting or disconnecting lamps,
harnesses or Head Extension Cables. Maximum distance, 30ft (2 x 15ft cables).

7
END VIEW SIDE VIEW
Mounting bracket, MTP-141 is required to mount the ballast to a
baby pin.
Loosen thumbscrew on the MTP-141 sufficiently to allow the flange
to insert into the track on the underside of the ballast.
A
A) Power Input: Connects to 12VDC power cable (4Pin xlr) or
24VDC cable (3Pin xlr).
B) Lamp Output: Connects to lamp Harness cable.
C) Dimmer Control: Adjusts light level of the Lamp.
D) Trim: Adjusts the bottom end of the dimming curve.
E) Power Switch: On/off power switch. Indicator lights up green
when power is applied.
B C D E

8
IMPORTANT: Prior to using the filter frame, remove translucent protective
plastic coating from both sides. Use the steel gel template to cut a filter to
the correct size. The filter is then taped to the transparent filter frame.
Baby shoe adapter, MTP-141S is used to mount the Ballast to a camera
equipped with a hot shoe receptacle.
Slide the flange of the MTP-141S into the hot shoe receptacle on the
camera. Lock the pin by screwing down the thumbscrew.
Mount the BAL-149X to the
baby pin as shown.

9
06C-K32 …. 6” T5 22 watt KF32, tungsten
06C-K55 …. 6” T5 22 watt KF55, daylight
GFR-KAM6….. .Kamio Gel Frame
GFR-KAM6T… Gel Frame Template
Kamio Lens Adapters
KAM58/85…58-85mm threaded ring adapter
KAM72/85…72-85mm threaded ring adapter
KAM80….... 80mm / fits Zeiss Super Speed Lenses
Canon 16X Mechanical Zoom
KAM82…... 82mm Lens adapter
KAM84…... 84mm / fits Panavision Digital Primes
KAM85.….. 85mm / fits many Canon & Fujinon zooms
KAM86…... 86mm / fits 1st Generation Canon HD
5.5 - 50 Zoom
KAM87…... 87mm / fits Zeiss T3 10:1 zoom
KAM89.….. 89mm / fits Canon XL1, 16X Auto Zoom
and 3X Auto Zoom
KAM93…… 93mm Lens Adapter
KAM-94….. 94mm / fits Canon XL2.
20 X 5.4 – 108mm Zoom
KAM95…... 95mm / fits Zeiss Ultra & Canon Zoom
KAM97…... 97mm Lens Adapter
KAM98…... 98mm Lens Adapter
KAM-100….100mm / fits Fujinon 17 (8-160mm Zoom)
KAM102…..102mm / fits Panavision Digital Zooms,
25 -112mm SDZT, 6-27mm SDZW
KAM104…..104mm / fits Arri Digital Primes
KAM110.….110mm / fits Cooke Primes
Note: 112mm clamp ring permanently fixed to Kamio
fixture. Fits Panavision®Primo Primes

10
HAR-KAM6…… Kamio 3ft lamp harness
KAM-6L…........ Kamio 6 Barn Door, Long
KAM-6S……. Kamio 6 Barn Door, Short (2pk)
MTP-141…….. Kamio Ballast Mount
MTP-141C…Kamio Ballast Clamp w/Baby Pin