Kirisun PT5200 User manual

FM HANDHELD TRANSCEIVER
INSTRUCTION MANUAL
PT5200

We are very grateful for your purchasing brand two-
way radios produced by Kirisun Electronics (Shenzhen) Co.,
Ltd.
We believe two-way radio, which always incorporates
the latest technology, can bring great convenience to your life
and work;
we also believe that the quality and function of two-
way radio can meet your demands for reliable communication.
PRECAUTIONS
Please observe the following precautions to prevent fire,
personal injury, and radio damage.
Do not operate your radio while taking on fuel, or being
charged.
Do not expose the radio for a long period to direct sunlight,
nor place the radio close to heating appliances.
Do not place the radio in excessively dusty areas, humid
INSTRUCTION MANUAL
FM HANDHELD TRANSCEIVER
23
PT5200
Voice Annunciation
Chinese English
Battery Save
OFF 1:1
1:2 1:4
3) Auxiliary Function Button Settings
Side Button 1 Side Button 2
Null (No function) Null (No function)
Call 1 Call 1
Call 2 Call 2
Cancel Emergency Cancel Emergency
Lone Working Lone Working
Monitor Monitor
Instantaneously Monitor Instantaneously Monitor
Temporarily Cancel Noise Channel Temporarily Cancel Noise Channel
Cancel Noise Channel Cancel Noise Channel
Adjustable Squelch Adjustable Squelch
Scan Scan
Scrambler Scrambler
Scrambler Backup Scrambler Backup
Cancel Squelch Cancel Squelch
Instantaneously Cancel Squelch Instantaneously Cancel Squelch
TalkAround TalkAround
Power Check Power Check
Whisper Whisper
VOX VOX
Battery Power Indication Battery Power Indication
TemporaryActivation of Channel TemporaryActivation of Channel
Annunciation Annunciation
Activation of Channel Activation of Channel
Annunciation Annunciation
Reverse Frequency Reverse Frequency

areas or on unstable surfaces.
Do not modify this radio for any reason.
Refer service to qualified licensed or certificated technicians
only.
Notice to the User:
Government laws prohibit radio communication without
permission in government districts.
Illegal operation is subject to punishment by fine and/or
imprisonment.
Refer service to the well-trained professional technicians only.
Safety
It is important that the user is aware of and understands hazards
common to the operation of any radios.
Warning!
Turn off your radio before entering any area with a potentially
explosive atmosphere (where the air contains gas, dust and
smog, etc.), such as while taking on fuel, or while parking at a
gasoline service station.
Precautions in Use
Please comply with the following attentions to avoid fire, bodily
injury and damage to the radio.
The radio is recommended to transmit for 1 minute and

receive for 4 minutes. Long time transmitting or continuous working in
high power mode will make the rear side of the radio generate heat.
Please don't disassemble or assemble the radio under any
circumstances.
Please don't expose the radio to direct sunlight for a long time;
don't place the radio near any heating devices, either.
Please don't put the radio in extremely dusty, moist or dabbling
places; don't place it on any unstable surfaces, either.
If the radio emits smoke or strange odors, turn it off and remove
the battery from the radio and promptly contact your local authorized
Kirisun dealer.
CONTENTS
Unpacking and Checking the Equipment .....................................1
Supplied Accessories .......................................................................1
Preparation.......................................................................................2
Charging the Battery...........................................................................2
Installing/Removing the Battery Pack................................................3
Installing the Antenna........................................................................4
Installing the Optional Speaker/Microphone.......................................4
Installing/Removing the Belt Clip........................................................4
Radio Overview.................................................................................5
Basic Operations .............................................................................6
Programmable Button Function.....................................................7
Wired Cloning Mode.......................................................................14
Auxiliary Functions........................................................................15
TOT (Time-out Timer).......................................................................15
Low Power Warning.........................................................................15
Channel Annunciation.......................................................................16
QT/DQT.....................................................................................16
User Solution....................................................................................16
Busy Channel Lockout (BCL)...........................................................17
SP Un-mute......................................................................................17
DTMF................................................................................................18
5-Tone...............................................................................................18
2-Tone...............................................................................................19
Transmitting Beginning/Ending Signaling.........................................19
Troubleshooting................................................................................20
Major Specifications.........................................................................21
Settings (by the Dealer)....................................................................22

ITEM QUANTITY
1
1
1
1
1
1
1
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the radio. We recommend that you
identify the items listed in the following table before discarding the
packing material. If any damage has occurred during shipment,
please contact the dealer immediately .
SUPPLIED ACCESSORIES
Hand strap
Belt clip
Li-Polymer battery
Charger
Power adapter
Instruction manual
Belt clip
Charger
Battery
Antenna
2
Antenna
PREPARATION
CHARGING THE BATTERY PACK
Notice:
1
Hand Strap
Power Adapter
Plug the power adapter into the proper AC wall
outlet; and insert the cable of the power adapter
into the adapter socket on the charger; then the
charger indicator lights yellow.
Insert the battery or the radio to be charged into
the charger slot.
Make sure the battery is in good contact with the
charger terminals. When the red indicator lights,
the charger begins to charge the battery.
After charging for about 5 hours, the red
indicator turns dim and the green indicator lights
indicating the battery has been fully charged.
Leave the battery in that sate of green indicator for 1~2 hours
before you remove it from the charger to achieve the best
performance of the battery. Then you can disconnect the power
adapter from the AC outlet.
* The battery is not fully charged in the factory, and please charge the
new battery when you use the radio for the first time.
* The radio is supplied with a KB-42A Li-Polymer battery
manufactured by KIRISUN.
* When you charge the battery for the first time after purchasing or
long storage, you should repeat charging it several times to achieve
the normal battery capacity.

INSTALLING /REMOVING THE BATTERY PACK
4
3
*
Notice:
Do not short-circuit the battery terminals or dispose exhausted
battery in fire.
Do not disassemble the battery casing.
*
INSTALLING THE OPTIONAL
SPEAKER /MICROPHONE
INSTALLING THE ANTENNA
Screw the antenna into the connector at
the top of the radio by holding the
bottom of the antenna and turn it
clockwise until secure.
Insert the Speaker/Microphone plug into
the jacks of the versatile connector.
Note:
When use the optional Speaker/
Microphone, the radio will not be
waterproof.
Match the grooves of the belt clip with
those on the rear of the battery.
Then press the belt clip downwards to
lock it in place.
To remove the belt clip, use your nail or
a tool to lift the metal spring piece in the
belt clip from the topside, and then pull
the belt clip away from the radio.
INSTALLING /REMOVING
THE BELT CLIP
* Do not recharge the battery if it has been fully charged or the battery
power doesn't become low, otherwise it might affect the battery life or
performance. Remove the battery from the charger after charging.
* The built-in protection circuit in the battery will cut off power when
power appears low. If you charge it in the charger then, the red
indicator won't light immediately. About 1~5 minutes later, the charger
indicator will become normal.
Installing the Battery Pack
Match the 2 bulges of the battery pack with the
corresponding slots at the rear bottom of the radio.
Installing the Battery Pack
Then firmly press the battery pack downwards to lock
it in place until a click is heard.
Removing the Battery Pack
To remove the battery pack, push the latch upwards
and then pull the battery away from the radio.

BASIC OPERATION
65
Switch On
Switch on the radio by turning the
Power/Volume switch clockwise till a click is
heard, then the radio will be in the state of
stand by and you will hear a beep if the dealer
has set it. And then you will hear voice
annunciation of the current channel number.
Adjust Volume
Press the monitor button to listen to the
background noise and rotate the Power/Volume
switch to adjust volume.
Select Channels
Rotate the channel selector to select channels.
You will hear voice from the speaker while
receiving proper signals.
If voice annunciation of channel number has
been set, the radio will annunciate the current
channel number.
RADIO OVERVIEW
LED Indicator
Lights red when transmitting; lights green when receiving.
Flashes orange when receiving the identical 5-Tone or 2-Tone
signaling.
Flashes red when battery power appears low.
Channel Selector
Rotate to select channel 1~16.
Power/Volume Knob
Turn clockwise to switch on the radio.
Turn counterclockwise till a click is heard to switch off the radio.
Rotate to adjust the volume after turning on the radio.
PTT (PUSH-TO-TALK) Button
To make a call, press and hold the PTT button, then speak into the
microphone in normal voice. Release the PTT button to receive
signals.
Side Button 1 (Programmable Button)
Side Button 2 (Programmable Button)
Top Button (Programmable Button)
Speaker/Microphone Jacks
Used to connect the optional speaker/microphone.
1
2
3
4
5
6
7
8

8
7
Make a Call
To make a call, select the desired channel,
press and hold the PTT button, and speak in
normal voice. Please keep your mouth 3~8 cm
away from the microphone.
Receive a Call
Release the PTT button to receive a call. Select the desired
channel, adjust the volume to a proper level, and then you can
receive others' voice.
SCAN FUNCTION
Programmable Button Function
The dealer can program the side button 1 and side button 2 with the
following auxiliary functions:
Null (No Function)
CALL 1
CALL 2
Alarm
Cancel Alarm
Individual Working
Monitor
Instantaneously Monitor
Temporarily Cancel Noise Channel
Cancel Noise Channel
Check Squelch Level
Adjustable Squelch
Scan
Scrambler
Scrambler Backup
Cancel Squelch
Instantaneously Cancel Squelch
Talk Around
Power Check
Whisper
VOX
Battery Power Indication
TemporaryActivation of Channel Annunciation
Activation of Channel Annunciation
Reverse Frequency
The dealer can program the following functions:
Null
No Function is programmed.
CALL 1/CALL 2
Press the side button set as Call 1 or Call 2 to transmit
the stored coding. Release Call 1 or Call 2 button and then press
PTT to call others and speak to the microphone.
Emergency
When you press the top button set as Alarm , the radio can
sound alarm tone or transmit ID code or background tone to your
partners or the system, both of which can be chosen in radio
programming with the software.
Cancel Emergency
Press the top button set as Alarm to cancel alarm function.

10
9
Individual Working
Press the side button set as Individual Working to enter
individual working mode, which ensures the user's security when
the radio is in individual working.
Notice: Individual Working is relevant with the auto checking mode
in the programming software and activated only when the both
functions have been set.
Monitor
Press the side button set as Monitor to turn off QT, DQT, 2-Tone
and 5-Tone and to hear the signals that cannot be heard when in
normal work. Press the Monitor key again to return to normal work.
Instantaneously Monitor
Press the side button set as Instantaneously Monitor to turn off
QT, DQT,2-Tone and 5-Tone and release it to return to normal work.
Temporarily Cancel Noise Channel
When the radio pauses on a certain channel during scanning, press
the button set as Instantaneously Cancel Noise Channel to
delete this channel from the scanning list temporarily.
Cancel Noise Channel
When the radio pauses on a certain channel during scanning, press
the button set as Cancel Noise Channel to delete this channel
from the scanning list permanently. The radio won't scan this
channel again after turning on the radio or it exits scanning.
Check Squelch Level
Press and hold the button set as Check Squelch Level to hear
the squelch level annunciation of the current channel.
Adjustable Squelch
Press the button set as Adjustable Squelch to change squelch
level. Press once to increase one level (cycle of 9-0; when at level
0 a beep sounds and squelch is activated) and store the change.
Scan
A) Press the button set as Scan to start scanning. When in
scanning, the radio checks signals on each channel; it stops
scanning and pauses on the channel on which signals are
detected until the signals disappear. If a delay time has been set
between the interval of signal disappearing and scanning
restarting, the radio will keep staying on that channel if it receives
any signals during the delay time.
B) The working channel of the radio will revert to the following
channels automatically when you press PTT button during
scanning. The dealer can select one among the following six
options.:
1) Selected channel
When pressing PTT button, the radio will transmit from the first
channel in the scanning list.
2) Selected channel + currently working channel
When pressing PTT button during scanning, the radio will always
transmit from the first channel in the scanning list. When pressing
PTT button during the scanning pause, the radio will always
transmit from the currently working channel
3) Priority channel
The radio will transmit from the priority channel in the scanning
list when you press PTT button.
4) Priority channel + currently working channel
When pressing PTT button during scanning, the radio will always
transmit from the priority channel. When pressing PTT button

12
11
during the scanning pause, the radio will transmit from the currently
working channel
5) Last called
When pressing PTT button, the radio will transmit from the last
channel that received a call.
6) Last used
When pressing PTT button during the scanning, the radio will
transmit from the last channel you used to talk.
C ) Priority Scan
During scanning, if the priority channel has been set on the radio,
when the priority channel receives signals the radio will
automatically switch to the priority channel even the normal
channel is receiving signals at that time. And the radio will stay on
the priority channel till the signals disappear. The dealer can set the
delay time between signal disappearing and continuing scanning.
D ) Temporarily Delete
When scanning pauses on a channel, press and hold the button
programmed as Temporarily Delete or Scan + Temporarily
Delete for 1 second to delete this channel temporarily from the
scanning list.
Note:
The priority channel cannot be deleted. And when the number of
scanning channels is less than 2, you cannot delete any channel,
either.
After exiting scanning mode and entering it again, the temporarily
deleted channel will be added in the scanning list again.
Scrambler
Press the button set as Scrambler to prevent the third party
from hearing clear your talking; and such a state will not be stored
after turning on the radio again or switching to other channels.
Scrambler Backup
Press the button set as Scrambler Backup to prevent the third
party from hearing clear what you are talking; and such a state will
be stored even after turning on the radio again or switching to
other channels.
Cancel Squelch
Press the button set as Cancel Squelch to turn on the
squelch; press it again to exit.
Instantaneously Cancel Squelch
Press the button set as Instantaneously Cancel Squelch to
turn on the squelch; release it to exit.
Talk Around
After you press the button set as Talk Around , the radio will
transmit in the receiving frequency when you press the PTT
button.
Power Check
Press and hold the button set as Check Power to hear the
current power level. One beep indicates low power; two beeps
medium power; and three beeps high power.
Whisper
After you press the button set as Whisper , your counterpart
can hear louder voice even you speak in a very low voice; press it
again to exit.
VOX (Voice-operated transmission)
Press the button set as VOX to enter the voice operated mode
and you can talk with your counterpart without pressing the PTT