SAFETY CAUTION
IMPORTANT NOTICE
OPERATING INSTRUCTIONS
1. Use this appliance for its intended purpose. Use only on clean, dry hair.
2. Close supervision is necessary when this appliance is by or near children.
3. Use only with accessories included in the package, (or those recommended by
the manufacturer).
4. Avoid contact with the eye area. Do not use on open wounds; damaged or
sensitive skin.
5. Except when charging, always unplug from the electrical socket after use.
6. Keep away from water, liquids or any detergent agents.
7.To avoid cord damage, do not pull, twist or wrap the cord tightly.
8. Charging should be done indoors and in a cool dry place.
9. The charger adaptor must be kept dry at all times.
1. The blade, main unit, power cord or attachment comb is damaged.
2. The clipper or the adapter is dropped into water or liquid.
3. The clipper is switched off, but the charging indicator does not light up when
plugged into the power source.
*The clipper and accessories must be checked regularly for damage. If damage is
detected, do not put the device into operation.
1. The blade must be lubricated before and after each use. This will maintain it in
good condition and will extend its service life.
2. Non - stop usage for hours may cause overheating of blades, reducing the cutting
performance and shortening their life. Should the blades overheat, switch the unit
off for a few minutes to let it cool down and lubricate the blades.
3. Hair must be clean and dry before cutting. Foreign matter hidden in the hair may
damage the blade edge.
4. Hair may gather inside the blade housing during use. Too much stored hair will
reduce the oscillating ability of the blades and cause malfunctioning.
Clean up hair in the blade housing before and after each use.
5. Avoid impact of the blade with hard objects as this may cause damage to the
blade teeth.
1. Do not overcharge. It takes (an estimate of)1 hour to charge your trimmer.
Charging more than 36 hours may shorten the life of the battery.
2. The life of the battery will be shortened if the trimmer remains uncharged for long
periods. Charge unused clippers every 3 months to activate and maintain the
battery.
3. It is normal for the adapter and the internal parts to become warm when charging.
1. Use or store the trimmer only at room temperature. Avoid direct sunlight,
moisture or heated surfaces. Operating range 0 - 40 ℃.
2. Do not attempt to unscrew any part of the trimmer.
1. Icon “ ” can be seen on LCD screen to remind you of charging.
2. Connect the charging cord to the charging slot at one end of clipper.
Should the following situations occur, unplug and switch off immediately,
and send for examination or repair.
Always switch off before removing, replacing and cleaning the blade.
Recharging time: 1 hour
Cordless operation time: 1.5 hours (5000RPM)
The “ ” icon will twinkled when the available time is only 5 mins left, to remind
you charging or connecting wires in time.
This trimmer can be operated electrically by plugging it into the power source
(when the battery is not fully charged).
1. Turn power switch off.
2. Connect the adapter to the wall socket.
3. Connect the DC plug to the clipper.
4. Check if the charging indicator is lit.
5. Switch on to operate.
* Except for the purpose of charging, always switch off and unplug the adapter
from the wall socket after use.
* Do not frequently use the clipper plugged in without having recharged the
battery, as this may reduce the life of the battery.
* Charge at room temperature between 5℃and 35℃.
1. Remove the blade set from the blade housing by pressing the top cutting head
with your thumb.
2. Brush off the residual collected hair thoroughly from between the teeth and the
blade housing.
3. Move the oscillating bracket with your thumb to separate stored hair from the
blades. Brush off the hair between the blades. Make sure hair is not trapped
between the blades.
Lubricate both friction surfaces of the front cutting teeth and the hind supporting areas.
1. Hind supporting areas: push the oscillating part to one side: lubricate the visible
friction surface on the other side. Drop a small amount of oil on both sides.
2. Front cutting teeth: Drop a small amount of oil on the blade teeth and spread evenly.
Slightly move the oscillating part to spread the oil between the blades.
1. To replace the blade set, put the bottom of the blade set clip into the blade set
Mount on the blade housing.
2. Push until it snaps into place.
1. Switch off and unplug the trimmer before cleaning.
2. Wipe with a soft damp cloth.
3. Allow it to air dry before use.
Keep Away from Water and Liquids
MAINTENANCE
Removing and Cleaning the Blade
Lubricating the Blade
Replace the Blade
Cleaning the Main Body and Accessories
Caution
Battery Condition Indicator
Cord Operation
Blade
Battery
Others
Changing
2 3
3. Confirm that the switch is off and insert the plug.
4. Charging indicator “low” & “ ”can be seen on LCD.
5. It will automatically stop after a full charge; both icons “low” & “high” can be
seen on LCD.
6. A full charging takes about 1 hour. The battery will reach optimum performance
after three charges.
