KiSS MC-690 User manual

1
PROFESSIONAL
CLIPPER
To ensure you achieve the best possible use of your clipper please read
the following instructions.
Ceramic blade
with acute angle
Power switch
Turbo
Blade length adjustor
High speed
Low speed
Battery status indicator
(High/ Low/ Charging)
MC-690
Rechargeable Heavy
Duty Clipper
Owner’s Guide
Component Name
Accessories
Oil bottleChargerCleaning brush
Universal voltage charger
Charger
Lubrication reminder
Comb attachment
(1.5mm, 3.0mm, 4.5mm, 6.0mm)

2 3
LED DISPLAY
SPECIFICATIONS
SAFETY CAUTION
SAFETY CAUTION
Blade
Battery
Hair
Clipper
Motor
Battery
Operating voltage: 3.2V
Rotation speed：6000±500rpm
3.7V, 2200mAh high-performance environment-friendly battery
Charging time: about 3 hours
Adapter
Operating time with full charge: about 6 hours
Input: AC 110V – 240V 50/60Hz
Output: DC 4.2V---1000mA
Keep the clipper away from moisture; do not submerge in water or liquid.
1. Use this appliance for its intended purpose. Use only on clean, dry hair.
2. Close supervision is necessary when this appliance is by or near children.
3. Use only with accessories included in the package, or those recommended by
the manufacturer.
4. Avoid contact with the eye area. Avoid use near or on open wounds, damaged or
sensitive skin.
5. Except when charging, always unplug from the electrical socket after use.
6. Keep away from water and all liquids and any detergent agents.
7. Do not pull, twist or wrap the cord tightly. Pull on the plug (not the cord) to
remove from power receptacle.
8. Charging should be done in a safe environment (between 0 and 40℃); indoors
in a dry place.
9. The charger adaptor must be kept dry at all times.
10. Do not disassemble the product.
1. The blade must be lubricated before and after each use. This will maintain good
condition and will extend its service life.
2. Nonstop usage for hours may cause overheating of blades, reducing the cutting
performance and shortening their life. Should the blades overheat, switch the unit off
for a few minutes to let it cool down; then lubricate the blades.
3. Hair must be clean and dry before cutting. Foreign matter hidden in the hair may
damage the blade edge.
4. Hair may gather inside the blade housing during use. Too much stored hair will
reduce the oscillating ability of the blades and cause malfunctioning. Always clean
away hair in the blade housing before and after each use.
5. Avoid impact of the blade with hard objects as this may cause damage to the
blade teeth.
1. Do not overcharge. It takes 3 hours to charge your trimmer. Charging over 36
hours may shorten the life of the battery.
2. The life of the battery will be shortened if the trimmer remains at less than full
charge for long periods. Charge unused clippers every 3 months to activate the
battery.
3. It is normal for the adapter and the internal parts to become warm when charging.
4. Please remove the battery safely and return it to the specified places when the
battery runs out. Never discard it casually.
OPERATING INSTRUCTIONS
Charging
1. When the power percentage is less than 5%, switch off the clipper to charge.
2. Connect the charging cord to the charging slot at one end of clipper.
3. Confirm that the switch is off and insert the plug.
5. It will automatically stop after a full charge.
6. A full charging takes an estimated 3 hours. The battery function will be at full
capacity after three charges.
Recharging time: 3 hours
11. The product can only be cleaned by cloth with little water or mild soap solution.
12. It’s normal for the product to produce little heat during using or charging.
13. Use or store the trimmer only at room temperature(between 0 and 40℃). Avoid
direct sunlight, moisture or heated surfaces and environments.
14. Except for the purpose of charging, always switch off and unplug the adapter
from the wall socket after use.
15. Do not frequently use the clipper plugged without having recharged the battery,
as this may reduce the life of the battery.
Should the following situations occur, unplug and switch off immediately, and send
for examination or repair.
1. The blade, main unit, power cord or attachment comb is damaged.
2. The clipper or the adapter is dropped into water.
3. The clipper is switched off, but the charging indicator does not light up when
plugged into the power source.
The clipper and accessories must be checked regularly to prevent damage and
ensure good performance.
If damage is detected, do not put the device into operation.
After long time constant use or when obstruction happens, the lubrication
reminder will light up.
2 level Motor Speed Display: High level (7000rpm), Low level (6000rpm)
Press the turbo switch to switch between the two levels.
Battery Status Indicator(100%/50%/Low). When battery is low, please charge
the clipper.

45
OPERATING INSTRUCTIONS MAINTENANCE
Install the Blade
Lubricating the Blade
Remove the Blade
Cleaning the Main Body and Accessories
Comb Attachments
Cord Operation
A
B
1. The cutting length is marked on the comb
attachments.
2. Select a suitable size and slide the blade into the
comb attachment. Hold both sides of the comb and
push until the comb is in position.
(Notes: The Comb should be placed firmly to ensure
safe operation.)
Align the blade (B) with
the trimmer slot (A).
Push the blade into the
slot until it snaps in
position.
2. Brush off the collected residual hair from between the teeth and the blade housing.
3. Move the oscillating bracket with your thumb to separate stored hair from the
blades. Brush off the hair between the blades. Make sure that hair is not trapped
between the blades.
You may adjust the cutting length from 3 - 6mm by attaching the comb attachment.
This trimmer can be operated by plugging it into the power source when the battery
is not fully charged.
1. Switch off.
2. Connect the adapter to the wall socket.
3. Connect the DC plug to the clipper.
4. Check if the charging indicator is lit.
5. Switch “On” to operate.
1. Before or after use, drop a small amount of
oil on the red-point places shown in the left
picture.
2. Drop oil and spread evenly. Slightly move the
oscillating part to spread the oil between the
blades.
1. Switch off and unplug the trimmer before cleaning.
2. Wipe with a soft damp cloth.
3. Allow it to completely air dry before use.
Please hold with the other hand to
avoid the blade falling off.
Press the moving part of the blade with
the thumb and then remove the blade.
Removing and Cleaning the Blade
1. Remove the blade set from the blade housing by pressing the top blade with your
thumb.
MAINTENANCE
Always switch off before removing, replacing and cleaning the blade.
Set blade adjuster to 2.0mm to reassemble blade; otherwise the adjuster does not work.
Feed tool
Post
Moving blade
Fixed blade
Blade Adjustment
Push up blade length
adjustor until it can not
move before installing the
blade.
1. The blade length adjuster is on the clipper.
2. Select the desired length of the blade by moving
the adjustment slide.
Select a blade with a suitable size before operation.

6
MOTOR LIFE
BATTERY LIFE
ENVIRONMENTAL DISPOSAL
BLADE LIFE
*The service life of the blade may be shortened in the following situations:
1. The blade has not been lubricated properly on a regular basis.
2. The blade cuts unclean hair or objects other than hair.
3. A foreign object damages the blade edge.
4. The blade is subjected to an impact.
If the cutting efficiency is reduced substantially despite proper maintenance, the
blade has exceeded its service life and should be sharpened or replaced.
*No maintenance is required for the motor.
*Professional DC motor.
*The service life of the motor may be shortened in the following situations:
1. The clipper is stored in humid environment for long periods.
2. The blade has not been lubricated properly.
3. Stored hair in the blade housing has not been cleaned properly.
4. An incorrect power source is used.
*The service life expectancy of the battery is approximately 3000 recharging cycles.
After that the charge will gradually drain and the power will be reduced.
*The service life of the battery may be shortened in the following situations:
1. The battery is stored in humid surroundings for long periods.
2. The battery is overcharged.
3. The battery is over depleted (when the battery is out of power, the clipper is kept
in the switched - on position for long periods).
4. The trimmer is always used plugged in.
5. The trimmer has not been charged for more than 3 months.
*When not in regular use, it is recommended to recharge the battery at least every
3 months.
*If cordless operation lasts for less than 10 minutes, despite proper charging, the
battery has exceeded its service life and should be replaced.
It is the owner’s responsibility to dispose of the clippers in a
reasonable manner after their useful life. Do not dispose of in
household waste.
The clipper can be returned to the place of purchase for recycling,
or taken to your local authority waste disposal site.
Producer : Shanghai TOEX International Trading Co., Ltd.
Address : Floor 5, Building 6, No.675 Zhujin Road, Songjiang District, Shanghai,
201615, China