KitchenAid Architect K6CP462K User manual

I"Ii
(91.4cm) (1 .9 cm)
Style Cooktop
backguard
(required for some installations)
/
36" (91.4 cm) cooktop with all
sealed burners shown
KJtchenAJd _
FOR TH E WAY IT'S MADE _'
Questions regarding features,
operation, performance, parts or
service? Call 1-800-422-1230 or visit
our web site at www.kitchenaid.com.
IMPORTANT:
Read and save these
instructions.
IMPORTANT:
Installer: Leave Installation
Instructions with the homeowner.
Homeowner: Keep Installation
Instructions for future reference.
Save Installation Instructions for local
electrical inspector's use.
Write down the model and serial numbers
before installing cooktop.
Both numbers are on the model/serial
number plate, located on the leftfront
underside of the cooktop burner box.
Model #
Serial # Part No. 8285479

Beforeyoustart,,,
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
Important: Observe all governing
codes and ordinances.
In the State of Massachusetts, the
following installation instructions
apply:
* Installations and repairs must be
performed by a qualified or licensed
contractor, plumber, or gasfitter
qualified or licensed by the State of
Massachusetts.
* If using a ball valve, it shall be a
T-handle type.
* A flexible gas connector, when used,
must not exceed 3 feet.
WARNING: If the
information in this manual
is not followed exactly, a
fire or explosion may result
causing property damage,
personal injury or death.
m Do not store or use
gasoline or other
flammable vapors and
liquids in the vicinity of
this or any other
appliance.
mWHATTO DO IFYOU
SMELL GAS
* Do not try to light any
appliance.
* Do not touch any
electrical switch.
*Do not use any phone in
your building.
* Immediately call your
gas supplier from a
neighbor's phone. Follow
the gas supplier's
instructions.
* If you cannot reach your
gas supplier, call the fire
department.
-- Installation and service
must be performed by a
qualified installer, service
agency or the gas
supplier.
The California Safe Drinking Water and
Toxic Enforcement Act requires the
Governor of California to publish a list of
substances known to the State of
California to cause cancer, birth defects,
or other reproductive harm, and requires
businesses to warn of potential exposure
to such substances.
WARNING: This product contains a
chemical known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
This appliance can cause low-level
exposure to some of the substances
listed, including benzene, crystalline silica,
carbon monoxide, toluene, and soot.
NOTE: This cooktop is manufactured for
use with Natural gas. To convert to
L.P./Propane gas, see the Gas
Conversion instructions provided in
literaturepackage.
Proper gas supply connection must be
available. See "Gas supply requirements."
Proper installation is your responsibility.
Have a qualified technician install this
cooktop.
Make sure you have everything
necessary for correct installation. It is the
responsibility of the installer to comply
with the installation clearances specified
on the model/serial rating plate. The
model/serial rating plate can be found on
the underside of the cooktop burner box.
it is recommended that an overhead vent
hood be used with this cooktop. For
island installations, a 48" (122 cm) hood
is recommended.
Check location where cooktop will be
installed. The location should be away
from strong draft areas, such as windows,
doors and strong heating vents or fans.
Do not obstruct flow of combustion and
ventilation air.
All openings in the wall or floor where the
cooktop is to be installed must be sealed.
Electrical ground is required. See
"Electrical Requirements."
it is the customer's responsibility:
•To contact a qualified electrical
installer.
To assure that electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA
70 -- latest edition*, or Canadian
Electrical Code, C22.1 -1982 and C22.2
No. 01982 (or latest edition)** and all
local codes and ordinances.
Copies of the standards listed may be obtained
from:
*Nationa! Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
** CSA international
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5578

Product Dimensions
36" (91.4 cm) cooktop with all
sealed burners shown
backguard/shown)
or island trim (see P. 4.and 7)
36"(91.4sin)lung
3-prongground-
typepower
supplysord 36" (01.4 cm) cooktop:35-710"(91.1 cm)
40" (121.9 cm) cooktop:47-718" (121.6 sin)
for 48" (121.0 sin)
8 burner model only:
6" (15.2 sin)
all other models:
(22.0sm)
"_ 26-1/4" (66.7 sin)
7/8" _
(22.2 ram) I J
2-3116"-........._-I j.._
(55.6 ram)
I
I
22" (55.9 sin)
side view of cooktep
jfor 48" (121.9 sin)
8burner model only:
3/8" 6" (15.2 sin)
(9.5 ram) all other models:
9"(22,9 sin)
7-1/8"
(18.1sin)
-'4--
gas inlet islocated 1-7/8" (4.8 cm) Iron]
-- back of burner box and
4-718" (12,4 cm) in from L.H. side of
burner,box
_,_.-..-1-3/'16'
(30.2 ram)

Cabinet and Cutout imensions
Countertop opening and clearance
dimensions that are shown must be
used. Given dimensions provide required
clearances.
Mobile home installation: The
installation of this cooktop must conform
to the Manufactured Home Construction
and Safety Standards, Title 24 CFR, Part
3280 (formerly the Federal Standard for
Mobile Home Construction and Safety;
Title 24 HUD part 280); or when such
standard is not applicable, the Standard
for Manufactured Home installations
(Manufactured Home Sites, Communities
and Setups), ANSI A225.1 --latest
edition*, or with local codes.
notchtobeequal
bothsides.
18" (45.7 cm) min.
clearance upper
cabinet to countertap
7-1/4"
(18.4 cm)
CORNERNOTCH
DETAIL
see corner
notch detail
In Canada, the installation of this cooktop
must conform with the current standards
CAN/CSA-Z240 -- latest edition**, or with
local codes.
The cooktop is designed to hang from the
countertop by its side and rear flanges.
The gas and electric supply should be
located as shown in "Gas and Electric
Dimensions," so that they are accessible
without requiring removal of the cooktop.
Provide cutout in left rear corner of cutout
enclosure as shown to provide clearance
for gas inlet, power supply cord, and to
allow the rating label to be visible.
Copies of the standards listed may be
obtained from:
* National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
** CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
22-1/4"
i(56.5cm)
"3/4"(1.9 cm)
(12.1 cm)
12-5/10" (31.3 cm)
rain. clearance to
side wall -
both sides
6-7/8" (16.1 cm)
(61cm)
basecabinet
size
36" (91.4 cm)
40" (121.0 cm)
model
K6CP462K
KGCP463K
KGCP467J
KGCP482K
KGCP483K
KGCP484K
KGCP487J
island trim
5"
(12.7 ¢m)
6II
(15.2cm)
5"
(12.7 cm)
6" (15.2 cm)
5H
(12.7 cm)
A
backgoard
1-3/4"
(4.4 cm)
1-3/4"
(4.4 ¢m)
5 II
(12.7 cm)
B(_in.)
island trim backguard
48" (121.9 cm)
48" (121.9cm)
48" 48"
(121.8¢m) (121.9cm)
48"
(121.9cm)
48" (121.9 cm)
C
backguard
opening
36"
(91.4 cm)
40"
(121,9 cm)
D
cabinetand
countertop
35-1/4"
(89.5 cm)
47-1/4"
(120.0cm)
countertoponly
36" (01.4 cm) or
35-7/8" (91.1 cm)
for zero clearance tit
48" (121.0 cm) or
47-7/8" (121.6 cm)
tar zero clearance tit
Note:Dimension"g" canbereducedby5" (15.2 cm)whenbottomofwoodor metalcabinetisprotectedbynotlessthan0.25"(6,4 ram)flameretardant
millbeardcoveredwithnotless thanNo. 28MSGsheetsteel,0.015"(0.4 ram)stainlesssteel,0.024"(0.5 mm)aluminumor 0.020"(8.5 ram)copper.

Gas and Electric
Dimensions
3-prongground-typeoutlet
shouldbelocatedonlefthand
sideofcutout8" 20.3 cm)
max. from eflc osuresdewa .
Gassupplylineshouldhe
locatedinthisareaonrearor
sidewalls,orthesupplylinecan
comeupthroughthefloor.
Gas and Electric
Connection Locations
productrating/serialtag controlsup_r_ panel
Note: Solid side and
bottom of cutout
enclosure net shown,
Gassupply
requirements
Explosion Hazard
Use anew AGA or CSA approved
gas supply line.
Install ashut-off valve.
Securely tighten all gas
connections.
If connected to LP, have a
qualified person make sure gas
pressure does not exceed 14"
water column.
Examples of a qualified person
include licensed heating
personnel, authorized gas
company personnel, and
authorized service personnel.
Failure to do so can result in
death, explosion, or fire.
Observe all governing codes and
ordinances.
important: Cooktop must be connected to
a regulated gas supply.
regulator (
with product) must he
installed with arrow up
pointing at ¢ooktop
bonom
1/2" nipple
(notsupplied)
AGAor CSA approved
flexible stainless
steel gas supply line
(not supplied)
shut off valve
(not supplied)
36" (91.4 cm)
3-prongground-type
power supply cord
\regulated gas
supply line
Typical Gas and Electric
Connections
Copies of the standards listed may be
obtained from:
* CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
A= This installation must conform with
local codes and ordinances, in the
absence of localcodes, installations must
conform with American National
Standard, National Fuel Gas Code
ANSI Z223.1 -- latest edition or
CANI -- B149.1 or 2*.
[] Input ratings shown on the
model/serial rating plate are for elevations
up to 2,000 feet (610 m). For elevations
above 2,000 feet (610 m), ratings are
reduced at a rate of 4% for each 1,000
feet (305 m) above sea level.
C gThe cooktop is equipped for use
with NATURAL gas. it is design-certified
by International Approval Services (I.A.S.)
for NATURAL and L.R gases with
appropriate conversion. The model/serial
rating plate, located on the underside of
the burner box, has information on the
type of gas that can be used. If this
information does not agree with the type
of gas available, check with the local gas
supplier. 5

L.P. Gas:
No attempt shall be made to convert the
cooktop from the gas specified on the
model/serial rating plate for use with a
different gas without consulting the
serving gas supplier. Conversion must be
done by a qualified service technician. To
convert to L.R gas, use LR gas
conversion kit part no. 8284934. The parts
for this kit are in the literature package
supplied with cooktop.
D= Provide a gas supply line of 3/4"
rigid pipe to the cooktop location. A
smaller size pipe on long runs may result
in insufficient gas supply. Pipe-joint
compounds, suitable for use with L.R gas,
must be used. With L.R gas, piping or
tubing size can be 1/2" minimum. L.R gas
suppliers usually determine the size and
materials used on the system.
E= If local codes permit, use a flexible
stainless steel tubing gas connector,
design-certified by AGA or CSA
International, to connect the cooktop to
the rigid gas supply line. 5/8" diameter line
is recommended. Do Not kink or damage
the flexible connector when moving the
cooktop. The pressure regulator has 1/2"
female pipe threads. Youwill need to
determine the fittings required, depending
on the size of your gas supply line, flexible
metal connector and shutoff valve.
shutoff va,ve el_-(_________
"open" positi
to coektop__
/_ gas supply
F line
=The supply line shall be equipped
with an approved shutoff valve. This valve
should be located in the same room as
the cooktop and should be in a location
that allows ease of opening and closing.
Do Not block access to the shutoff valve.
The valve is for turning on or shutting off
gas to the appliance.
G • If rigid pipe :-_J__
is used as a gas I_
supply line, a combination of pipe _l
fittings must be used to obtain an in-line
connection to the cooktop. All strains
must be removed from the supply and
fuel lines so cooktop will be level and in
line.
=The regulatormust be checked at a
minimum 1-inch(2.5 cm) water column
above the set pressure.The inlet pressure to
the regulator should be as follows for
operation and checking the regulatorsetting:
NATURAL GAS:
Set pressure 5 inches (12.7 cm) W.C.
Supply pressure 7-14 inches (17.8 cm
to 35.5 cm) W.C. maximum.
LP. GAS:
Minimum pressure 10 inches
(25.4 cm) W.C.
Supply pressure 14 inches
(35.5 cm) W.C.
_= Line pressure testing:
Testing above 112psi (3.5 kPa) or
14 inches (35.5 cm)W.C. (gauge)
The cooktop and its individual shutoff
valve must be disconnected from the gas
supply piping system during any pressure
testing of that system at test pressures
greater than 1/2 psig (3.5kPa).
Testing below 1/2 psi (3.5 kPa) or
14 inches (35.5 cm)W.C. (gauge) or
lower
The cooktop must be isolated from the
gas supply piping system by closing its
individual manual shutoff valve during any
pressure testing of the gas supply piping
system at test pressures equal to or less
than 1/2 psig (3.5 kPa).
Electrical
requirements
Electrical Shock Hazard
Plug into a grounded 3-prong
outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
If codes permit and a separate ground
wire is used, it is recommended that a
qualified electrician determine that the
ground path is adequate.
Check with a qualified electrician if you
are not sure whether the cooktop is
properly grounded.
Do not ground to a gas pipe.
A 120-volt, 60-Hz, AC-only, 15-ampere,
fused electrical supply is required. A
time-delay fuse or circuit breaker is
recommended. It is recommended that a
separate circuit serving only this
appliance be provided.
Electronic ignition systems operate within
wide voltage limits, but proper ground and
polarity are necessary. In addition to
checking that the outlet provides 120-volt
power and is correctly grounded, the
outlet must be checked by a qualified
electrician to see if it is wired with correct
polarity. A wiring diagram is provided on
the last page of these instructions.
Important: This cooktop is equipped with
an electronic ignition system that will not
operate if plugged into an outlet that is
not properly polarized.
This appliance, when installed, must be
electrically grounded in accordance with
local codes or, in the absence of local
codes, with the current CSA standard
C22.1. Canadian Electrical Code Part 1".
Recommended ground method
For your personal safety, this cooktop
must be grounded. This cooktop is
equipped with a3-prong ground plug. To
minimize possible shock hazard, the cord
must be plugged into a mating 3-prong
ground-type outlet, grounded in
accordance with the National Electrical
Code ANSI/NFPA 70 latest edition** or
Canadian Electrical Code (CSA)* -- and
local codes and ordinances. If amating
outlet is not available, it is the personal
responsibility and obligation of the
customer to have a properly polarized
and grounded, 3-prong outlet installed by
a qualified electrician.
3-prongpolarized
ground-type outlet _
a-prong
ground plug
power
supply cord
Copies of the standards listed above may be
obtained from:
*CSA international
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5578
** National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269

Installation
t [] Remove the top wood sheet from
over the top of the cooktop.
_ Remove the shipping brackets and
discard.
Excessive Weight Hazard
Use two or more people to move
and install cooktop.
Failure to do so can result in back
or other injury.
= Carefully lift the cooktop up and set
aside. Write down the model and serial
numbers before installing the cooktop.
Both numbers are on the model/serial
number plate located on leftfront
underside of the burner box.
_ Unpack the burner grates, burner
caps, simmer plate, grille grate, drip tray,
spill guard, wave tray,wave plate, tile
bezels, regulator, backguard and island
trim. items are either packaged under the
cooktop or on the cooktop. Parts shipped
with cooktop depend on model ordered.
= The pressure regulator and flexible,
stainless steel gas supply lineconnector
can be assembled to the cooktop now or
after the cooktop is installed in the cutout.
To assemble now, stand the cooktop on its
side or back surface and complete this
part of the pressure regulator/gas line
connector assembly.
To connect the flexible, stainless steel
connector to the pressure regulator
requires a 1/2" nipple.
Installthe pressure regulator with the
arrow pointing up toward the bottom of the
burner box and in a position where you
can reach the regulator cap.
iMPORTANT: All connections must be
wrench-tightened. Do not make
connections to the gas regulator too tight.
Making the connection too tight may crack
the regulator and cause a gas leak. Do not
allow the regulator to turn on the pipe
when tightening fittings.
Use only pipe-joint compound made for
use with Natural and L.R gas. Do not use
teflon tape. You will need to determine the
fittings required depending on your
installation.
°48"(121.gcm)modelswithbothgrilleand
griddle donotusescrewA
,,36" (91.4 cm) modelswithgriddle donotuse
screw B
•All other models use all 3front screws
.3 rear screws required bet not shownon48"
(121.g cm) models and 2 rear screwsrequired
but net shown on 36" (91.4 cm) models
attaching the
backgoard
,,48" (121.9 cm) models with both grille and
griddle use screws at Dand E
•All other models use screwsat Cand E
c
attaching the
island trim
[] Attach the backguard or island trim
as required for your installation. Attachment
screws are in the literature package.
_ Carefully lift and place the cooktop
intothe front area of the cutout. Be
careful not to pinch the power supply cord
or damage the pressure regulator/flexible
gas supply line connector if installed. DO
NOT place all the way back into cutout.
[] Place cooktop completely into
cutout. NOTE: The cooktop must be level
for best cooking performance.
[] If the pressure regulator and
flexible, stainless steel gas supply
were not assembled in Step 3,
complete the assembly now. The
pressure regulator MUST be installed
with arrow on the regulator pointing up
toward the burner box.
0[] Connect flexible, stainless steel
gas supply connector to the rigid gas
supply line. Do not kink the connector. You
will need to determine fittings required
depending on your installation.
shuteff valve _
"open" p0sitioe /_
gas supply.. _----'_"1._'! _r_
/_ to cooktop
11 •Openshutoffvalveinthegas
supply line. Wait a few minutes for gas to
move through the gas line.
t2 [] Leak testing of the appliance
shall be conducted according to the
following instructions:
Test all connections by brushing on an
approved non-corrosive leak-detection
solution. Bubbles will show a leak. Correct
any leak found.
ignitor burner cap
electrode
"_'-_ burner
base
/
gas tube "
opening
3 [] Put burner caps on each burner
base. Place burner grates over burner
bases and caps.
if your model has only surface burners
(no grille or griddle), go to "Check the
operation of the surface burners, grille
and griddle."
4 [] If your model was shipped with
a grille or griddle, go to "Installing the
grille or griddle" to complete the
instaJlation.

lnstaJling the grille
or griddle.
Grille installation: Go to Step 15.
Griddle installation: The griddle is
factory installed. Tocomplete the
installation, go to Step 16.
5=Installing the grille:
log burner
A= Lifttheiog burnerup outofthe bay
and setaside.
locating feet
%\
tray
B= Place drip tray on bottom of grille
bay and slide the tray forward so that it is
located side-to-side and against the
locating feet of the rear spill guard.
insert feet
into slots
C= Insert the front spill guard feet into
the slots in the rear spill guard as shown.
The rear flange will rest on the burner box.
8
D= Reinstall the log burner. Make sure
burner's rear flange is seated in slot.
E= Plug power supply cord into
grounded outlet.
F= Check the surface burner and grille
flames. Before completing the grille
installation, go to "Check the operation of
the surface burners, grille and griddle."
slot for
g tab
locating
tab
/
G= Install the wave tray into the
grille/griddle bay. The tab in the leftrear
corner of the bay must fit through the slot
in the left rear corner of the wave tray.
wave wave
}late
\
H= Place the wave plate on the wave
tray as shown. The wave plate must be
centered on the wave tray.
_= install the grille grate.
t6 [] Completing the griddle
installation:
griddle
drip tray
A= Place drip tray in the well at the
front of the griddle. Slide tray forward until
it stops.
B. Refer to the Use and Care Guide
that came with your Cooktop for
instructions on cleaning and seasoning
the griddle before using.
C= Plug power supply cord into
grounded 3-prong outlet.
D= Check the surface burner and
griddle flames. Go to "Check the
operation of the surface burners, grille
and griddle."

Checkthe
operationof the
surfaceburners,
griJJeandgriddJe,
Electronic Ignition System m
initial lighting
Surface burners use electronic ignitors
in place of standing pilots. When the
cooktop control knob is pushed in and
turned to the "LiTE" position, the system
creates aspark to light the burner. This
sparking continues until the control knob
is turned to the desired setting.
The grille and griddle burner use an
ignitor glow bar that is either on or off in
place of standing pilots. When the glow
bar is hot, it sends a signaJ back to the
safety valve which opens allowing gas to
flow.
cooktop grille griddle
burners knob knob
A= Push in and turn the surface
burners and grille control knobs to "LiTE"
position. For griddles, turn the griddle
control knob to atemperature degree
mark (300 ° recommended). The surface
burner flame should light within 4
seconds and the grille and griddle flame
in 30-40 seconds. Note: the griddle flame
cannot be seen, but you should hear it
ignite and feel heat from the griddle.
After lighting the burners, turn the
control knobs "OFF".
If burners do not light properly, turn
control knob to the "OFF" position. Check
that burner cap is in the proper position.
Check that power supply cord is plugged
in and that circuit breaker or house fuse
has not blown. Check that the shutoff
valve is in the "ON" position. Check
operation again.
If a surface burner, grille or griddle does
not light at this point, contact your
KitchenAid dealer for assistance.
B, Adjusting the surface burner or
grille flame: NOTE: there is no
adjustment for the griddle flame. Gas flow
is at 100%, temperature is controlled by
thermostat.
Push in and turn each control knob to the
"LO" position. The "LO" setting of each
burner has been factory set to the lowest
position available to provide reliable
reignition of the burner. If it does not stay
lit on the "LO" position, check "LO"
position as follows:
a.Turn control knob to "LITE" until burner
ignites.
b. Quickly turn control knob down to "LO"
position.
c. If burner goes out, readjust valve as
follows:
Remove control knob. Insert a flat-blade
screwdriver into the hollow valve stem
and engage the slotted screw. Flame size
can be increased or decreased by turning
the screw. Adjust flame until you can
quickly turn control knob from "HI" to "LO"
position without extinguishing the flame.
Flame should be as small as possible
without going out.
ports
C= Check flame on "HI" for a blue
color. It should be clean and soft in
character. No yellow tip, blowing or lifting
of flame should occur. Occasional orange
flashes are normal and reflect different
elements in the air or gas.

JnstalJercheckoff
Jist:
COOKTOP
_] Cooktop correctly positioned in
countertop cutout.
[--vT-]Maintained specified distances to
cabinet surfaces.
_] Cooktop level - front to back - side
to side.
[-7-] Burner caps positioned properly on
sealed burner bases.
_] All packing material removed.
_] Backguard or island trim attached
(see page 4).
[--vT-]Depending on model, grille parts
correctly assembled.
[-7] Depending on model, griddle parts
correctly assembled.
ELECTRICAL
_] Polarized and grounded 120-volt,
60-Hz, AC, 15-amp fused electrical
supply for power supply cord
connection.
GAS SUPPLY
[--vT-]Connection: 1/2" NPT with a
minimum 5/8" (15.9 mm) diameter
flex line.
_] The cooktop is connected only to
type of gas for which it is certified for
use.
if cooktop does
not operate:
_ Check that the circuit breaker is not
tripped or the house fuse blown.
[]Check that the power supply cord is
plugged into the outlet.
_] Check that gas valves are turned to
the "ON" position.
_See Use and Care Guide for
troubleshooting list.
if youneed
assistance:
TheKitchenAidConsumerAssistanceCenter
willansweranyquestionsaboutoperatingor
maintainingyourcooktopnotcoveredin the
InstallationInstructions.The KitchenAid
ConsumerAssistanceCenteris open 24
hoursa day,7 days a week.Justdial 1-800-
422-1230-- the call isfree withinthe
continentalUnitedStates,or visit ourweb site
atwww.kitchenaid,com.
Whenyoucall, youwill needthe cooktop
modelnumberand serial number.Both
numberscanbe foundon the model/serial
ratingplatelocatedon the bottomof the
cooktopand are visiblethroughthecutout in
the left-handback cornerofthe enclosure
bottom.
In the event that your KitchenAid
appliance should need service, caii the
dealer from whom you purchased the
appliance or a KitchenAid-designated
service company. A KitchenAid-
designated service company is listed in
theYeJJow Pages of your telephone
directory under "Appliances --
Household -- Major -- Service and
Repair"
You can also obtain the service
company's name and number by dialing,
free within the continental United States,
the KitchenAid Consumer Assistance
Center telephone number, 1-800-422-
1230.A special operator will tell you the
name of your nearest KitchenAid-
designated service company.
Maintain the quality built into your
KitchenAid appliance -- call a
KitchenAid-designated service company.
Maintenance
If removing the cooktop is necessary for
maintenance, shut off gas supply.
Disconnect the gas and electric supply.
After disconnecting the gas and electric
supply, finish removing the cooktop.
Generally, the cooktop does not need to
be removed for servicing.
10

36" (91.4 cm)cooktopmodels
THE POWER CORD ON THIS APPLIANCE IS EQUIPPED WITH A 3-PRONG GROUND PLUG
WHICH MATES WITH STANDARD 3-PRONG GROUND-TYPE OUTLET.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION
VERIFY PROPER OPERATION AFTER SERVICING.
6 Surface burners
LINE PLUG LINEEE_
1/4 WIDE
1/4 WIDE 5/16 WIDE BLAD
BLADE BLADE
120 VAC 60 Hz
ROUND BLADE 1 PHASE
15 OR 20 AMP BK
GRN OR GRN/Y ]1'
B GROUND
l
BK RiB
CONNECT SPARK
250 TERMINALS MODULE
BK
SURFACE BURNER
VALVE
SWITCHES t !
±±±2 LZ
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55° TO 95 COUNTER CLOCKWISE FROM OFF
L]NEE_
1/4 WIDE
BLAD
THERMOSTAT
4 surface burners with griddle
DLU( _R_ EUTRAL
5/16WIDE
BLADE
GROUND
UND BLADE 120 VAC 60 Hz
1 PHASE
_KRIB 15 OR 20 AMP
B GRN OR GRN/Y t I_GROUND
BK
BK J W W
_- SPARK
--d o-4 / MODULE
SURFACE BURNER I I _I
sw_ALVHEEs L_jL_ _ YEL ORBRN4PLCS
±Z±±
GRIDDLE_ SURFACE BTJRNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55° TO 95° COUNTER CLOCKWISE FROM OFF
GRIDDLE
VALVE
4 surface burners with grille
_LU( _RO NEUTRAL
5/16 WIDE
BLADE
GROUND 120 VAC 60 Hz
UND BLADE 1 PHASE
15 OR 20AMP
3K RIB
GRN OR GRN/Y IIEGROUND
BK
BK _J W
i i
BK BK - _ - _. SPARK
II _ MODULE
SURFACE BURNER
VALVE
SWITCHES
GRILLE
VALVE
SWITCH
GRILLE
VALVE
w
L_ YEL OR BRN
f/-4 PLCS
SURFACE BURNER
IGNITOR ELECTRODES
GRILLE
IGNITOR
SWITCHES ON SURFACE BURNER
VALVES:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 55 TO 95 °
COUNTER CLOCKWISE FROM OFF
SWITCH ON GRILLE VALVE:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 20 TO 360 °
COUNTER CLOCKWISE FROM OFF
11

48" (1:21.9cm)coektopmodels
THE POWER CORD ON THIS APPLIANCE IS EQUIPPED WITH A 3-PRONG GROUND PLUG
WHICH MATES WITH STANDARD 3-PRONG GROUND-TYPE OUTLET.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS.
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION
VERIFY PROPER OPERATION AFTER SERVICING
8surface burners 6 surface burners with grille
LINE PLUG NEUTRAL
1/4WIDE 5/16 WIDE
BLADE BLADE
GROUND 120 VAC 60 Hz
ROUND BLADE 1 PHASE
15 OR 20 AMP
I1'GROUND
CONNECT B__I _
250 TERMINALS BK IC q
SPARK /
BL_::_ I IMODULEI
I , , I
........ YEL OR BRN
2_± ± ± ± ± ± ± 5PLCS
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55 +TO 95+ COUNTER CLOCKWISE FROM OFF
LINE
1/4WIDE
BLADE
3LUC _RO NEUTRAL
5/16 WIDE
BLADE
GROUND
UND BLADE
BK RIB
GRN OR GRN/Y
I
BK
SURFACE BURNER
VALVE SWITCHES
GRILLE
VALVE SWITCH
120 VAC 60 Hz GRILLE
1 PHASE VALVE
15 OR 20 AMP
t+'GROUNDBK [_
w w
Lix_ '
SPARK
MODULE GRILLE
IGNITOR
_1_--_ ------_L --I _- --! J _ YBL OR BRN
$ $ $ Szz 6PLCS
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE
BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 55+ TO 95
COUNTER CLOCKWISE FROM OFF
SWITCH ON GRILLE VALVE:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 20 TO 360+
COUNTER CLOCKWISE FROM OFF
6 surface burners with griddle
L,N_
1/4 WIDE
BLAD _RRO NEUTRAL
=LU( 5/16WIDE
BLADE
GROUND
UND BLADE
BK RIB
GRN OR GRN/Y
120 VAC 60 Hz
1 PHASE
15 OR 20 AMP
I_ GROUND
BK
SWITCHES ON SURFACE BURNER VAL\/ES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB
IS ROTATED 55 +TO 95 +COUNTER
CLOCKWISE FROM OFF
I
BK W
BK BK
GRIDDLE
SPARK IGNITOR
MODULE
SURFACE BURNBR _1___ _--_ _l ___ _! I l
VALVE SWITCHES
L_
GRIDDLE_ YEL OR BRN
THERMOSTAT __ __ __ __ __ __ 6PLCS
SURFACE BURNER
IGNITOR
ELECTRODES
GRIDDLE
VALVE
w
4 surface burners with grille and griddle
LINE _ ) _nNEUTRAL
1/4W_DE LU 5/16WIDE
BLADE -- BLADE
%%_,%_ 120VAC50HzGR,LLB
Bt _ tKRI: ......... 151PHA_Mp VALV_
__GRN OR GRN/Y Iij GROUND W
, w _ woBK _ TBKT
BK BK GRILLE
_l_ _/_ ,_m_o_
_o---_ I ! SPARK II /
,BK _--# I I M°DULE I I GRIDDLE
\ _ I I II ! F_]I I VALVE
__SURFACEswITCHEsVALvEBURNERiii E_ i ii _] II IEBK
GRILLE I _ | I / / I / T T
VALVBSWITCH I____ I i - J
- - _ 4 PLCS /V
1 YEL OR BRN /
L_2C ± z ± ± I I/_
GR,DDLBW ....
SURFACE BURNER GRIDDL
THERMOSTAT EtLGENcITTORDES E
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB
IS ROTATED 55° TO 95° COUNTER
CLOCKWISE FROM OFF
Part No. 8285479
© 2003 KitchenAid.
® Registered Trademark/Trademark of
KitchenAid U.S.A., KitchenAid
Canada licensee in Canada
KJtchen_kJd ®
HOME APPLIANCES
Prepared by KitchenAid, Benton Harbor, Michigan 49022 Printed in U.S.A.

instructionsd'instailation
a
Style
ecuisson _az KitchenAid °
, cm(36 po)
1, cm (48 po)
_mmerciai-
Oosseret
(n_cessaire pOUr certaines
installations)
Table de cuisson b bruleurs
scell_s de 91,4 cm (36 po)
Kitchen_kid _
BIEN PENSI_, BIEN FABR]O_I_ _' Pour toute question concernant caracteristiques, utilisation, performance,
piece ou service, t61ephonerau
1-800-422-1230 ou consulter notre site
Internet a I'adresse www.kitchenaid.com
IMPORTANT,"
Lire et conserver cos
instructions,
IMPORTANT :
Installateur : Remettre les instructions
d'installation au proprietaire.
Propri_taire : Conserver les instructions
d'instaliation pour consultation ulterieure.
Conserver les instructions d'installation
pour consultation par I'inspecteur local
des installations electriques.
Inscrire ci-dessous les numeros de
modeie et de serie avant d'installer la
table de cuisson.
On trouve cette information sur la plaque
signaletique, sur la surface interne du
coffret des brQleurs.
N° de modele
N° de serie N° de piece 8285479

Avantde commencer...
Votre s_curit_ et celle des autres
est tr_s importante.
Nous donnons de nombreux
messages de securit6 importants dans
ce manuel et sur votre appareii
menager. Assurez-vous de toujours
Jire tous Jes messages de securit6 et
de vous y conformer.
Voici Je symboie d'aJerte de
secufit&
Ce symboie d'alerte de
securit6 vous signale les dangers
potentiels de deces et de blessures
graves a vous et a d'autres.
Tousles messages de securit6
suivront le symbole d'alerte de
securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots
signifient :
Risque possible de d_c_s ou de
blessure grave si vous ne suivez pas
imm_diatement les instructions.
Risque possible de d_c_s ou de
blessure grave si vous ne suivez
pas les instructions.
Tousles messages de securit6 vous
diront quel est le danger potentiel et
vous disent comment reduire le risque
de blessure et ce qui peut se produire
en cas de non-respect des instructions.
Important : Observer les dispositions de
tousles codes et reglements en vigueur.
AVERTISSEMENT : Si les
instructions dans ce
manuel ne sont pas
suivies, un incendie ou une
explosion peut causer des
dommages aux biens, une
blessure ou un d@ces.
m Ne pas remiser ou utiliser
d'essence ou un autre
produit liquide ou gazeux
inflammable _ proximit@
de cet appareil ou de tout
autre appareil
@lectrom_nager.
QUE FAIRE Sl UNE
ODEUR DE GAZ EST
PERCEPTIBLE?
• Ne pas essayer de
mettre un appareil en
marche.
• ae toucher aucun
commutateur _lectrique.
• N'utiliser aucun
t_l@phone de r@difice.
• Contacter
imm_diatement le
fournisseur de gaz
depuis le t@l@phone d'un
voisin. Ex_cuter les
instructions du
fournisseur.
• Si le fournisseur de gaz
n'est pas accessible,
appeler les pompiers.
Uinstallation et les
travaux de service doivent
6tre effectu_s par un
@lectricien qualifi@, par
une agence de service ou
par le fournisseur de gaz.
Remarque : Cette table de cuisson est
con_ue pour I'alimentation au gaz naturel.
Pour la conversion au gaz propane, voir
les instructions de conversion present6es
dans les documents qui accompagnent le
produit.
Un raccord de connexion a la canalisation
d'arrivee de gaz dolt _tre disponible. Voir
"Specifications de I'alimentation en gaz."
La responsabilite de la qualite de
I'installation incombe au proprietaire.
Demander a un technicien qualifie
d'executer I'installation.
Verifier que tout le materiel necessaire pour
une installation correcte est disponible.
C'est a I'installateur qu'incombe la
responsabilite de respecter les
degagements de separation specifi6s sur la
plaque signaletique. On trouve la plaque
signaletique sur la face inferieure du coffret
des brQleurs.
On recommande qu'une hotte d'extraction
soit installee au-dessus de la table de
cuisson. Pour I'installation sur un riot, on
recommande une hotte de 122 cm (48 pc).
Inspecter I'emplacement 0(4la table de
cuisson sera installee. I'emplacement
d'installation devrait 6tre situe a distance
de route source de courants d'air
intenses, comme fen6tres, porte, bouche
de chauffage ou ventilateur.
Ne pas entraver la circulation d'air de
combustion et d'air de ventilation.
Toutes les ouvertures decoup6es dans le
mur ou dans le plancher au voisinage de
I'endroit oQ la table de cuisson sera
installee doivent _tre scellees.
Une liaison 61ectrique & la terre est
necessaire. Voir "Specifications de
I'installation electrique."
C'est au client qu'incombe la
responsabilit_ :
• de contacter un _lectricien qualifi_
pour rinstallation.
• de s'assurer que l'installation
_lectrique est ad6quate et conforme
aux dispositions du Code national des
installations _lectriques ANSlIFNPA 70
- derni_re 6dition*, ou du Code
canadien de l'_lectricit_ C22.1-1982 et
C22,2 n°01982 (ou derni_re 6dition)**,
et aux dispositions des codes et
r_glements locaux.
On peutse procurerdes exemptairesdes normes
indiqueesaux adressessuivantes:
• National FireProtection Association
One Batteryrnarch Park
Quincy,Massachusetts 02289
•* CSA International
8501 East PleasantValley Rd.
Cleveland, Ohio 44131-5575

imensions u produit
table de caisson & brt_leurs scell_s
de 91,4 cm (36 po)
cordon
d'alimentatJonde
91,4cm(36po)
avecfichede
hranchement_3
hroches(liaison
laterra) 91,1 cm po)table de caissonde 91,4 cm (36 po) : (35 7/8
table de caissonde 121,9 cm (48 pa) : 121,_o) ./
dasseret(representS)
au bien garniture pour installation
sur[lot (voir p. 4 et 7) Pourlos modules de
121,9 cm (48 po)_ 8
br_leurs uniquement :
15,2 cm (6 po)
Teas les autres modNes :
(9pa)
66,7 cm (26-1N po)
J
(716po) /
55,6 mm ----'_- _-'_55,9 cm (22
(2-3116 po)
66,7 cm (26-1/4 pa)
po)
Pourlos modNes de
121,gcm (46 po) _ 6
br_leurs uniquement :
9,5 mm 15,2 cm (6 po)
(3/6I' po) Teas les autres madNes :
22,9 cm (9 po)
I
16,1 cm
(7-1/6po)
{
entree de la canalisatJonde gaz _ 4,8 cm
-- -- (1 7/8 po) de I'arri_re da coffretdes
br_lears el _ 12,4 cm (4 7/8 po) depais le
c6t_ gauche du coffret des br_leurs.
30,2mm
(13/16po)
table de caisson(vue lat_rale)

imensions - placard et ouverture d couper
Respecter lesdimensions indiqu_es
pour I'ouverture & d_couper etles
distances de s_paration. Les dimensions
indiquees tiennent compte des
degagements de securit6 necessaires.
installation darts une r_sidence mobile :
I'instailation de cette table de cuisson dolt
satisfaire les criteres de la norme
Manufactured Home Construction and
Safety Standards, titre 24 CFR, partie 3280
(anciennement norme fed6raie pour
construction et securit6 des residences
Au Canada, rinstallation de cette table de depose de la table de cuisson.
cuisson dolt satisfaire les criteres de la Prevoir une ouverture d6coupee dans
norme CAN/CSA-Z240 (derniere edition)** I'angle arriere gauche de la cavite
ou des codes Iocaux en vigueur, d'encastrement pour le passage de
La table de cuisson est congue pour qu'elle I'arrivee de gazet du cordon d'alimentation
salt soutenue sur le plan de travail par les electrique, et pour que la plaque
rebords des cStes et de I'arriere. signaletique salt visible.
Les arrivees de gaz et d'electricit6 Onpeutseprocurerdes exempiaires des normes
devraient 6tre placees selon les indications indiqueesauxadressessuivantes:
de rillustration "Dimensions - arrivees de *NationalFireProtectionAssociation
gaz et d'electricit6", pour que I'acces aces One Batterymarch Park
points de connexion salt possible darts Quincy,Massachusetts 02269
mobiles, titre 24 HUD partie 280); ou si ** CSA international
, • 8501 East Pleasant Valley Rd
cette norme nest pas apphcable, L., ..
,. ............ I_'----------_ Cleveland, Ohio 44131-5575
I ins[aria[ion oo1[ sa[isTalreaesprescnpuons I
de la norme d'installation des residences _ C_ ,
prefabriqu6es (Manufactured Home Sites, _ _
Communities and Setups) ANSi A225.1 - I /I _ 1
derniere edition* ou lesprescriptions des _ /_ _ .......__
distancemin.de I I
..... 45,7cm (18 po_ I i
['enc.ocn.enp,i __ entre placard et [_'-----._ _._ J
elre ega]enes /plandetravail "_
uau×colas. -" IJ _ C__.____...___._. gmin.
18,4 cm 1,9 cm (3/4 pa)
(71/4po) vaird_taHs 56,5cm
de I'angle (22-1/4 po)
,/,,"-- 16,1 cm (6 7/8 pa)
ENCOCHEBANS
L'ANGLE-DETAIL 12,1 cm
(4 3/4 pc) distance de
s_paration du mur
lat6ral, rain. 31,3 crn
/"5,1 cm (12 5/16 po) de
/___E cheque c_t_ (24 po)
D placard
inf_rieur
faille
91,4 cm(36 po)
121,gcm
(48pa)
module
KGCP462K
KGCP463K
KGCP467J
KGCP482K
KGCP483K
KGCP484K
KGCP487J
A
garniture de I'[Iot
12,7 ¢m
(5po)
15,2 cm
(6po)
12,7 cm
(5no)
15_2cm (6 no)
12,7 cm
(5po)
dosseret
4,4 cm
(13/4pa)
4,4 cm
(1 3/4 po)
7,6 cm
(3 pc)
B(r_in.)
garnituredeHint dosseret
121,9cm(48po)
121,9cm(48po)
surface noncombustible
121,9 cm 121,9 cm
(48po) (48po)
non combustible
121,g cm
(48po)
121,9cm (48po)
nancombustible
C
ouverture
pourdosseret
91,4 cm
(36 po)
121,9 cm
(48pc)
D
placardat
plandetravail
89,5 cm
(35 1/4po)
120,{) cm
(47 1/4 po)
plan de travail seulement
91,4 cm (36 po) ou
91,1 cm (35 7/8 po)
avec dt_gagementnul
121,9 cm (48 po) ou
121,6 cm (47 7/8 po)
avec d_gagement nul
Bemarque :A mains d'avis contraire, les dimensions sent callas de la distance de s_paration entre une surface combustible.

linens!arts - Arriv es de
azet ' lectricit
Placerla prisede courant(3 air,ales, reli_e
Ioterre)surle cat_gauchedelacavit_
d'encastrement,_20,3¢m(8 po)aumainsde
lapardiiat_rale delacavited'encastrement.
Remarque: C6t_
plainetfendde Io
cavit_d'encostrement
pasrepr_sent_s.
La¢analisatiand'arriv_edegazdevrait_tre
plaebedanscartezone_ I'arfi_reoudansla
pare!laf_ra]e;oubienlacanalisafiandegaz
peut_treacheminbe_ traversieplancller.
Raccordement au× canal!sat!arts
de gaz et de r@lectricit_
support du tableau
de commando
plaque signal_tique __
dafnndnurIfourniavee ::a_ cordond'al,nnntafien ioooI-_P°"
table
le produit) - lers de -"-----4110iii_ _ _- 91 4cm (36 po} ave¢
I'installation, ofienter _/___ "_f fiche de I_ranchement
la fl_ehe vers In hoof, /-'F_ _ \\ 3broches fliaison _ Io
vnrslefondde,atable/ _ _9 terra) "
decoisso. /_ _'_
raccord 1/2 pa '_ ._._<=_t_
conduit de raccordement canalisation d'arriv_e
flexible, d'ocier inoxydable rob!net d'arr_t de gaz -press!on
(pas fourni) - hemelogation (pas foorni) r_gul_e
AGA eu CSA
Raccordements typiques au× circuits
de gaz et de r@iectricit@
On peut se procurer des exemplaires des
normes indiquees a I'adresse suivante •
CSA international
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
Specifications
de i'aiimentation
engaz
Risque d'explosion
Utiliser un conduit de raccordement
la canalisation de gaz approuv_
par AGA ou CSA.
Installer un robinet d'arr_t.
Bien setter tous les joints des
raccords du circuit de gaz.
Si I'appareil est reli_ _une
canalisation de gaz propane,
demander _ une personne qualifi_e
de v_rifier que la pression de gaz ne
d_passe pas 14 po (colonne d'eau).
(Personnes qualifi_es =personnel
competent d'un fournisseur
d'_quipement de chauffage, d'une
compagnie de distribution de gaz, ou
d'une entreprise d'entretien agr_e).
Le non-respect de ces instructions
peut causer un d_c_s, one explosion
ou un incendie.
Observer les dispositions de tousles codes et
reglements en vigueur.
Important : La table de cuisson dolt _tre
connectee aune source de gaz a pression
regulee.
A= Uinstallation realisee selon ces instructions
dolt &tre conforme aux dispositions des codes et
reglements Iocaux. En I'absence d'un code local,
I'instattation dolt &tre conforme aux dispositions de
la norme American Nationa! Standard, National
Fuel Gas Code ANSI Z223.1 - derniere edition*
ou de la norme CANI-B149.1 ou 2*.
[] La capacite thermique indiquee sur la
plaque signaletique correspond &une altitude
inferieure a 610 m (2000 pi). Pour une altitude
superieure a 610 m (2000 pi), reduire la capacite
thermique a raison de 4 % pour chaque tranche de
305 m (1000 pi) au-dessus du niveau de la mar.
C[] Cette table de cuisson est equipee pour
I'alimentation au gaz NATUREL. Sa conception est
homotoguee par International Approval Services
(I.A.S.) pour I'alimentation au gaz NATUREL ou au
propane (avec conversion appropriee). La plaque
signaletique, situee sur la face inferieure du coffret
des brOleurs, mentionne te type de combustible
utitisable. Si cette information ne concorde pas
avec le type de gaz disponibte, consulter te
fournisseur de gaz local.

Propane :
Ne jamais tenter, sans avoir d'abord consulte le
fournisseur de gaz, de modifier ta table de
cuisson pour I'alimentation avec un autre gaz
que celui specifi6 surta plaque signaletique.
Toute conversion dolt 6tre execut6e par un
technicien qualifie. Pour la conversion au
propane, utiliser I'ensemble de conversion n°
8284934. Ces pieces accompagnent les
documents foumis avec ta table de cuisson.
D g installer une canalisation de gaz rigide de
1,9 cm (3/4 pc) jusqu'a I'emplacement de ta table
de cuisson. L'emptoi d'une canalisation de
diametre inferieur sur une grande distance peut
rendre le debit de gaz insuffisant. Utiliser un
compose d'6tancheit6 des jointures congu pour
I'utilisation en presence de propane. Pour
I'alimentation au propane, utiliser une canalisation
de diametre d'au mains 1/2 pc. Habituettement, le
foumisseur de propane determine la taitte des
canatisations a utiliser avec te systeme.
E g Siles codes ou les reglements Iocaux le
permettent, on recommande I'emptoi d'un conduit
de raccordement metallique flexible (homologation
American Gas Association ou CSA international,
pour te raccordement de la table de cuisson a ta
canatisation de gaz. On recommande une
canalisation de diametre 5/8 pc. Veiller ane pas
deformer ou endommager le conduit flexible Iors
des deplacements de la table de cuisson. Le
detendeur comporte un fitetage femelle de 1/2 pc.
On devra determiner quels raccords sont
necessaires, selon la taille de ta canalisation de
gazet les caract@istiques du robinet d'arr6t et du
conduit de raccordement metallique flexible.
[]Contr61er le fonctionnement du
detendeur a une pression d'au mains 2,5 cm (1
pc) (colonne d'eau) au-dessus de la pression
nominale. La pression a I'entree du detendeur en
service devrait 6tre comme suit :
GAZ NATUREL :
Pression de reglage de 12,7 cm (5 pc)
(coionne d'eau)
Pression d'alimentation maximale de
17,8 a 35,5 cm (de 7 & 14 pc)
GAZ PROPANE :
Pression minimale de 25,4 cm (10 pc)
(coionne d'eau)
Pression d'alimentation maximale de
35,5 cm (14 pc)
_[] Test de la canalisation d'arriv@e :
Test sous pression relative sup@rieure
3,5 kPa (1/2 Ib/po 2)ou 35,5 cm (14 pc)
(colonne d'eau)
La table de cuisson et le robinet d'arr6t individuet
doivent _tre d6connectes de la canalisation de
gaz au cours des tests du circuit d'alimentation
une pression relative sup@ieure & 3,5 kPa
(1/2 tb/po 2)
Test sous pression relative de 3,5 kPa
(1/2 Ib/po 2) - 35,5 cm (14 pc) (colonne d'eau) -
OU mains
La table de cuisson dolt 6tre isolee de la
canalisation de gaz par fermeture du robinet
d'arr@t individuet au cours des tests du circuit
d'alimentation sous une pression egale ou
inf@ieure a 3,5 kPa (1/2 Ib/po2).
Specificationsde
I'instaliation
r0bJnet d'arrOt --_
canalisatinn "auvert". ..._)/_'_
°'orriv,e,eoo, lectrique
__ vers latable
Fde cuisson
[] La canalisation d'arrivee de gaz devra
comporter un robinet d'arr@t homologue. Ce
robinet d'arr6t devra _tre situe dans la m6me
piece que la table de cuisson, a un emplacement
permettant un acces aise pour les manoeuvres
d'ouverture et de fermeture. Ne pas entraver
t'acces au robinet d'arr6t; celui-ci est utilise pour
ouvrir et interrompre t'alimentation en gaz de
t'appareil.
G[] Si la canalisation _
_;,g;;_t_IsU_e _uyaute_ii:a,son de raccclc, S _ '
de tuyauterie pour reatiser un raccordement
dans t'alignement de la table de cuisson. Toute
tension mecanique dolt @tre ¢liminee de ta
canalisation de gaz, de mani@e que la table de
cuisson demeure horizontale et alignee.
Risque de choc 61ectrique
Brancher I'appareil clans une prise
de courant _ trois alv@oles reli@e
la terre.
Ne pas eniever la broche de liaison
la terre.
Ne pas utiliser un adaptateur.
Le non-respect de ces instructions
peut causer un d_c_,s, un incendie
ou choc _lectrique.
Si, Iorsque tes codes le permettent, un
conducteur distinct de liaison a ta terre est
utilise, it est recommande qu'un electricien
qualifie v@ifie ta qualite de la liaison & la terre.
Consulter un electricien qualifie en cas de doute
au sujet de ta liaison a ta terre de ta table de
cuisson.
Ne jamais utiliserune canalisationde gaz pourla
liaisonelectriquea laterre.
L'appareil dolt 6tre alimente par un circuit
electrique de 120 V (CA seulement), 60 Hz, 15
ou 20 A, protege par un fusible. On recommande
I'emploi d'un fusible temporise ou d'un
disjoncteur. On recommande que cet appareil
salt alimente par un circuit independant,
n'atimentant que cet appareit.
Le systeme d'allumage electronique fonctionne
dans une fourchette de tensions assez large,
mais il faut que I'appareil salt convenablement
relie a la terreet queta polarite salt respectee.
V@ifier que la prise de courant electrique est
correctement reliee& la terreet fournit une
tension de 120 V. Demander egalement & un
electricien qualifie de v@ifier que la polarite de la
prise de courant est correcte. Un schema de
c&blage est presente a la derni@e page de cette
brochure d'instructions.
important :Cette table de cuisson est dotee
d'un systeme d'allumage electronique qui ne
fonctionnera pas si etle est branchee sur une
prise de courant incorrectement polarisee.
Lorsqu'it est insta!le, cet appareil dolt @tre
electriquement retie & ta terre conformement aux
dispositions des codes Iocaux ou, en t'absence
de codes locaux, conformement aux dispositions
de la norme courante CSA C22.1 (Code
canadien de t'etectricite, l@e partie).
M_thode recommand_e de
liaison a la terre
Pour la securite des utilisateurs, cet appareit dolt
_tre relie a la terre. Cet appareil est equipe d'un
cordon d'alimentation dote d'une fiche de
branchement a 3 broches, pour liaison a la terra.
Pour minimiser le risque de choc electrique, te
cordon dolt @tre branche sur une prise de
courant murale correspondante, a 3 alveoles,
reliee a ta terre, conformement aux dispositions
de I'edition la plus recente** du Code national de
I'electricite ANSI/NFPA 70 ou du Code canadien
de I'electricite (CSA)*, et des codes et
reglements tocaux en vigueur. Si une prise de
courant compatible avec la fiche n'est pas
disponible, c'est au proprietaire de t'appareil
qu'incombent la responsabilite et t'obtigation
personnelles de faire installer par un electricien
qualifie une prise de courant a 3 alveoles
correctement retiee a la terre. _..___
prise de ceurant _ 3 air,ales,
re,i,e, la terra -__o_
fiche de branchement
3 bracbes, pour - _- I// I
liaison _ la torte _ brioche de
cordon d'alimentatian---_ll .liaison
_lectriqoe ia terra
On peut se procurer des exemplaires des
normes indiqu_es aux adresses suivantes :
*CSA international
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5578
** National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269

Installation
= Oter la feuilte de bois recouvrant la table
de cuisson.
= Oter les cornieres d'exp6dition et tes
mettre au rebut.
Risque de poids excessif
Utiliser de[ix oil pl[isde personnes
pour d6placer et installer la c[iisni6re,
ke non-respect de cette instruction
pe[it causer Line bless[ire all dos oil
d'a[itres bless[ires.
3[] Soulever prudemment la table de cuisson
et la mettre de c6t6. Inscrire tes numeros de
modele et de serie avant d'installer la table de
cuisson. Les deux numeros se trouvent sur ta
plaque signaletique se trouvant sur la face
inferieure avant gauche du coffret des brOleurs.
[] D6balter les accessoires - grilles de
brOleur, chapeaux de brOleur, plaque de
mijotage, grille du grit, plateau ramasse-gouttes,
protecteur anti-deversement, plateau nervure,
plaque nervuree, encadrements a carreaux,
detendeur, dosseret et garniture (pour Tlot). Les
accessoires se trouvent sous ou sur ta table de
cuisson. Les pieces expedi6es avec ta table de
cuisson dependent du modele commande.
[] II est possible de connecter le detendeur
et le conduit de raccordement flexible d'acier
inoxydable des maintenant ou apres I'installation
de la table de cuisson dans la cavite
d'encastrement. Pour effectuer immediatement ce
raccordement, placer la table de cuisson en appui
sur te c6t6 ou t'arri6re, et connecter le detendeur.
Un raccord de 1/2 po est necessaire pour ta
connexion entre te conduit flexible d'acier
inoxydable et te detendeur.
Lors de I'installation du detendeur, orienter la
fleche vers le haut, vers le fond du coffret des
brQleurs, et orienter le detendeur de telle maniere
qu'it salt possible d'atteindre facilement le bouton
de r6glage.
IMPORTANT : Serrer chaque connexion avec une
cle, mais ne pas serrer excessivement te raccord
dans le detendeur; ceci pourrait provoquer une
fissuration du detendeur, suscitant une fuite. Lors
du serrage des raccords, veiller ace que te
detendeur ne pivote pas par rapport au tuyau.
Utiliser uniquement un compose d'6tancheit6
pour jointures compatible avec le gaz naturel et
te propane. Ne pas utiliser du ruban de teflon, li
sera necessaire de determiner quels raccords
utiliser, seton ta configuration d'installation.
3vis avant (3 vJs
arri_re n_cessaires
mais pas repr_sent_es)
installation du
dasseret
2 vis
installation de la
garniture pourilot
trou ceetral
pas utilis6
[] Fixer le dosseret outa garniture pour flat,
selon la configuration d'instaltation. Les vis de
fixation se trouvent dans te sachet de
documentation.
[] Soutever prudemment la table de cuisson
pour ta placer dans la partie avant de la cavite
d'encastrement. Veiller a ne pas coincer te
cordon d'alimentation et a ne pas endommager
te detendeur et le conduit de raccordement
flexible. NE PAS pousser la table de cuisson
completement vers te fond de ta cavite
d'encastrement.
[] Introduire compl6tement la table de
cuisson dans la cavite d'encastrement.
Remarque : Pour qu'elle produise la meitleure
performance de cuisson, it faut que ta table de
cuisson salt d'aplomb.
[] Si le detendeur et le conduit de
raccordement flexible d'acier inoxydable n'ont
pas et6 install6s a t'6tape 3, effectuer maintenant
cette installation. Veiller a orienter la fleche du
detendeur vers te haut, vers te coffret des
brGleurs.
t0 [] Connecter le conduit de
raccordement flexible d'acier inoxydable sur la
canalisation d'arrivee de gaz rigide. Ne pas
deformer le conduit de raccordement flexible. II
sara necessaire de determiner quels raccords
utitiser, selon la configuration d'instaltation.
robinetd'arr_t -
canalisation ouvert __
_ _ verslatable
de cuJssan
t [] Ouvrir te robinet d'arr6t de la
canalisation de gaz. Attendre pendant quelques
minutes que te gaz remplisse ta canalisation.
t2 [] Executer un test de recherche des
fuites conformement aux instructions ci-dessous.
Effectuer une inspection de recherche des fuites
sur chaque connexion; utitiser une solution non
corrosive approuvee a cette fin. La formation de
bulles identifie une fuite. Effectuer tes corrections
necessaires pour eliminer toute fuite observee.
_lectrode 0 _
d'aHumage
ouvertur
du tube z
d'arfiv_e
de gaz
chapeau de
brOJeur
base du
brOleur
3, Placer le chapeau de brQleur sur
chaque base de brGleur. Placer la grille de
brQleur sur chaque brGleur.
Si votre modele n'est muni qua de brQleurs de
surface (pas de gril ni de plaque a frire), passer
"Verification du fonctionnement des brGleurs de
surface, du gril et de la plaque a frire.".
t4 [] Si votre modete a 6te exp6die avec
un gril ou une plaque a frire, passer
"Installation du grii ou de la ptaque a frire" pour
achever I'installation.

Installation dugril oude
Japlaque frire
installation du gril: Passer & t'etape 15.
installation de la plaque _ frire :La plaque &
frire est installee a t'usine. Pour achever
I'installation, passer a I'etape 16.
5= Installation du gril :
BrOleur
A= Soulever le brt_leur hors de la cavite et le
mettre de c6te.
piedsrepute
plateau
ramasse-
gauttes
B. Ptacer le pretecteur anti-deversement au
fond de ta cavite du grii et glisser le ptateau vers
I'avant de telle serte qu'ii se trouve en position
transversale contre tes pieds repere du
protecteur anti-deversement arriere.
plodset
fentes
C= Inserer les pieds du protecteur anti-
deversement avant darts tes fentes du protecteur
anti-deversement arriere. Le rebord arriere
reposera sur le coffret des brQleurs.
8
D= Reinstalter le brQleur. S'assurer que le
rebord arriere des brQleurs repose darts ta fente.
E= Brancher le cordon d'alimentation sur une
prise de courant reliee & ta terre.
F. Verifier les flammes des brQteurs de
surface et du gril. Avant d'achever I'installation du
gril, passer & "Verification du fonctionnement des
brQleurs de surface, du gril et de ta plaque &
frire."
tentepour
I'angletrep_re--
ongiet
rep_re
G. Installer te plateau nervure darts la cavite
du grit ou de ta plaque a frire. Uongtet darts te
coin arriere gauche de la cavite dolt passer
travers ta fente darts le coin arriere gauche du
plateau nervure. plaque
plateau
nervure
\
H= Placer la plaque nervuree sur le plateau
nervure tel qu'itlustre. La plaque nervuree dolt
6tre centree sur te plateau nervure.
_= Installer ta grille du gril.
6 = Achevement de I'installation
de la plaque a frire :
plateau ramasse-geuttes
de la plaque _ trite
A= Placer le plateau ramasse-gouttes dans
le puits a t'avant de la plaque a frire. Glisser le
plateau vers I'avant jusqu'& I'arr6t.
B. Consulter le Guide d'utilisation et
d'entretien livre avec la table de cuisson pour
des instructions sur le nettoyage et le
conditionnement de ta plaque & frire avant son
utitisation.
C= Brancher le cordon d'alimentation sur une
prise de courant reliee & ta terre.
D. Verifier tes flammes des brCtteurs de
surface et du gril. Passer a "Verification du
fonctionnement des brGleurs de surface, du gril
et de la plaque a frire."