KitchenAid KHPF 7510 User manual

KHPF 7510
KHPS 7510
Instructions for use
5019_719_01132_GB 1-06-2007 14:30 Pagina 1

5019_719_01132_GB 1-06-2007 14:30 Pagina 2

Product description and symbols 4
Using the burners 4
Practical advice on using the hob 5
Positioning the pan supports and wok support 5
Hood and cabinetry clearances (mm) 6
Injector table 6
Warnings and suggestions 7
Safeguarding the environment 8
Installation (Flush and Traditional fitting) 9
Gas connection 9
Electrical connection 10
Fixing the Hob to the supporting structure.
Traditionally fitted model (Semi Flush fitting). 10
Fixing the Hob to the worktop. Flush fitted model. 11
Adaption to a different type of gas supply 12
Replacing the injectors 12
Fitting the wok burner 13
Regulating the minimum flow level of the gas taps 13
General cleaning & maintenance 14
Care and maintenance of the gas burners 14
Troubleshooting guide 15
After Sales Service 15
5019_719_01132_GB 1-06-2007 14:30 Pagina 3

1. Removable pan supports
2. 1 kWh auxiliary burner
3. 1.65 kWh semi-fast burner
4. 1.65 kWh semi-fast burner
5. Professional wok burner
6. Auxiliary burner control knob
7. Semi-fast burner control knob
8. Semi-fast burner control knob
9. Professional wok burner control knob
Control Symbols
Off
Maximum flame
Minimum flame
Product description and symbols
To turn on one of the burners:
1. Turn the corresponding control knob
anticlockwise until the indicator coincides with
the maximum flame symbol .
2. Press the control knob to ignite the burner.
3. Once the burner has lit, keep the control knob
pressed for about 5 seconds to allow the safety
thermocouple fitted to each burner to engage.
The thermocouple will switch off the gas supply
to the burner should the flame be accidentally
lost ( A gust of air, momentary interruption of
gas supply or liquid spillage etc).
If the burner does not ignite within about 15
seconds, switch off the burner, check the
fitting of the burner cap and plate for correct
fitting. Wait at least 1 minute before trying
again.
If the burner goes out when the control knob
is released, the thermocouple did not engage.
wait al least 1 minute before repeating strps 1
to 3.
Using the burners
4
5019_719_01132_GB 1-06-2007 14:30 Pagina 4

Read the instructions to get the best out of your
hob.
• Use pans with a similar diameter to the
burner(see the table).
• Use flat bottomed pans except with the wok
support.
• Do not use excessive water when cooking
foods and use the lid.
• Ensure that pans are fully supported by the pan
supports and do not protrude over the edges.
You should never use:
• two burners simultaneously with just one
container such as a fish kettle.
Burner Ø Pans
wok from 24 to 26 cm
semi fast from 16 to 24 cm
auxiliary from 8 to 14 cm
Practical advice on using the hob
Position the pan supports and wok support as indicated in the figure.
Positioning the pan supports and wok support
5
5019_719_01132_GB 1-06-2007 14:30 Pagina 5

Category II2H3+
Electric Power: 230 V - 50 Hz
If a hood is to be installed above the hob, refer to the hood
installation instructions to ensure the correct height above
the hob.
Note: If the distance “A” between the kitchen wall cabinets is
between 600 and 730 mm, height “B" shall be at least 530
mm.
If the distance “A” between the kitchen wall cabinets is wider
than the hob’s width, height “B shall be at least 400 mm.
Hood and cabinetry clearances (mm)
Injector table
6
Type of gas used Type of
burner
Injector
label
Control
primary air
(X) (mm)
Nominal
heat flow
kW
Nominal
consumption
Reduced
heat flow
kW
Gas pressure (mbar)
min. nom. max.
NATURAL GAS
(Methane) G20
wok
semi-fast
auxiliary
145
95
78
6
-
-
4,20
1,65
1,00
400 l/h
157 l/h
95 l/h
1,40
0,40
0,30
17 20 25
LIQUID
PETROLEUM
GAS (Butane)
G30
wok
semi-fast
auxiliary
100
65
50
11
-
-
4,20
1,65
1,00
305 g/h
120 g/h
73 g/h
1,40
0,40
0,30
20 28-30 35
LIQUID
PETROLEUM
GAS (Propane)
G31
wok
semi-fast
auxiliary
100
65
50
11
-
-
4,20
1,65
1,00
300 g/h
118 g/h
71 g/h
1,40
0,40
0,30
25 37 45
Type of gas used Configuration model Nominal heat flow kW Overall nominal
consumption
Required air (m3) for
the combustion 1 m3of
gas
G20 20 mbar 4 burners 8,5 809 l/h 9,52
G30 28-30 mbar 4 burners 8,5 618 g/h 30,94
G31 37 mbar 4 burners 8,5 607 g/h 23,80
5019_719_01132_GB 1-06-2007 14:30 Pagina 6

To get the most out of your hob, please read
the instructions carefully and keep them for
future consultation.
• These instructions are only valid in the countries
whose destination symbol is shown on the serial
number plate on the hob.
• The packing (plastic bags, expanded
polyurethane, etc) pose a potential threat to
children and should be disposed of carefully.
• Check the appliance has not been damaged
during transportation and remove all
protective packing and films before
installation.
• This hob (cat. 3) was designed to be used
exclusively for cooking food in household
surroundings. Any other use (for example
heating rooms) should be regarded as
improper and dangerous.
• The installation and connection of this
appliance to a gas or electrical supply must
be carried out by a competant, qualified
person in compliance with current
legislation.
• This appliance should be installed in
compliance with standards in force and
only used in well ventilated rooms. Read
the instructions before installing and using
this appliance.
• The pre-fitted gas connector and it's supply
pressure are shown on the label attached
to the bottom of the hob. If this type of gas
supply is not being used, please refer to
the section called Adaption to different
types of gas supply on page 11.
Note:
• Incorrect placement of the pan supports can
scratch the hob. To avoid this always ensure
that the rubber feet on the bottom of the pan
supports are the only part of the pan supports
that touch the hob and do not drag the pan
supports accross the hob surface.
• On the glass surface do not use:
- Cast iron grills, terracotta pots or pans.
- Heat convectors (e.g. metal netting).
- Using two burners to cook 1 pan.
• In the event of prolonged usage, additional
ventilation may be required (opening a window
or increasing the extration speed of the hood).
Warning
• Keep children away from the hob when in use
and don't let them play with the control knobs
or any other part of the appliance.
• Do not let children play with the pan supports.
The rubber feet on the underneath of the pan
supports could be swallowed by small and cause
serious injury or suffocation.
• Before replacing the pan supports on the hob,
please check that all the rubber feet are in
place.
• Each time you finish using the hob, always check
that the control buttons are in the off position
and shut off the tap to the gas mains or cylinder.
• Do not obstruct the air vents at the back of the
appliance in any way.
Warnings and suggestions
7
5019_719_01132_GB 1-06-2007 14:30 Pagina 7

Packing
The packing material is 100% recyclable and is
labelled with the recycling symbol . Please
dispose of all packing responsibly and carefully.
Product
This appliance is marked according to the
European Directive 2002/96/EC, Waste Electrical
and Electronic Equipment (WEEE).
By ensuring that this product is disposed of
correctly, you will help prevent potentially negative
consequences for the environment and human
health.
The symbol on the product, or on the
documents accompanying this appliance indicates
that this product should not be disposed of as
household waste. Please dispose of this appliance
at an Electrical & Electronic Equipment Collection
point as in accordance with local environmental
regulations for waste disposal. For details of your
local Collection Point please contact your Local
Authority.
Conformity declaration
This hob was designed, built and marketed
incompliance with:
• the safety requirements in the “Gas” CEE
Directive 90/396
• the safety requirements of “Low Voltage
Directive” 2006/95/EC (replacing 73/23/EEC
and subsequent amendments)
• the protection requirements of the “EMC” CEE
Directive 89/336
• the requirements in CEE Directive 93/68
• this appliance was designed to come into
contact with foods and complies with EC
Regulation 1935/2004.
Note:
• Incorrect placement of the pan supports can
scratch the hob. To avoid this always ensure
that the rubber feet on the bottom of the pan
supports are the only part of the pan supports
that touch the hob and do not drag the pan
supports across the hob surface.
• Do not use two burners to cook 1 pan.
• In the event of prolonged usage, additional
ventilation may be required (opening a window
or increasing the extraction speed of the hood).
Warning
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensor or mental capabilities or lack of
experience and knowledge unless they have
been given initial supervision or instruction
concerning use of the applaince by a person
responsible for their safety.
• Keep children away from the hob when in
use and don't let them play with the
control knobs or any other part of the
appliance.
• Do not let children play with the pan
supports. The rubber feet on the
underneath of the pan supports could be
swallowed by small and cause serious injury
or suffocation.
• Before replacing the pan supports on the
hob, please check that all the rubber feet
are in place.
• Each time you finish using the hob, always
check that the control knobs are in the off
position and shut off the tap to the gas
mains or cylinder.
• Do not obstruct the air vents at the back
of the appliance in any way.
Safeguarding the environment
8
5019_719_01132_GB 1-06-2007 14:30 Pagina 8

Technical information for the installer
•Warning: this is a heavy products which
requires the installation to be carried out
by two people.
• When installing the hob it is advisable to wear
protective gloves.
• This appliance can be installed into a 20mm -
50mm thick worktop.
• If no oven is to be installed below the hob, a
panel must be fitted under the hob to prevent
hob damage and protect the cupboard contents.
This panel must cover the whole of the
underside of the hob and must be positioned so
that an air gap of at least 50mm between the
panel and hob underside is maintained, as a
minimum, and as a maximum 150mm to the
underneath of the work surface.
• This hob is designed to operate perfectly with
any oven in the KitchenAid range. The
Manufacturer declines all responsibility should
any other make of oven be installed. The
manufacturer declines all responsibility
should another make of oven be installed.
Before installation, please ensure that:
• The gas supply (type and pressure) and the
calibration on the hob are compatible (see serial
number plate on the hob and the injector table).
• The cabinetry and appliances surrounding/next
to the hob are heat resistant and in compliance
with local regulations.
• The products of combustion are removed from
the atmosphere in the room by using an
extraction hood or electrical fan installed to the
walls and or windows, in line with current
regulations.
• The air circulates naturally through a suitable
opening that is no less than 100cm2in cross
section, which must be:
- permanent and accessible on the walls of the
room being ventilated and extracting towards
the outside.
- created in such a way that the openings both
inside and out cannot be obstructed, even in
error.
- Protected by plastic grill, metallic netting etc.
that should not reduce the 100cm2cross
section.
- Located in such a position so as not to
interfere with the extraction of the products
of combustion.
Installation (Flush and Semi-Flush fitting)
Connection to the mains gas system must be carried out by a
competant, registered person, in compliance with current
legislation.
• The connection of the hob to the gas mains network or gas
cylinder must be done using a rigid copper or steel pipe with parts
that comply with local standards, or using a flexible stainless steel
pipe with continuous surfaces that comply with local standards.
The flexible metallic pipe should be no longer than 2 linear
metres.
• Before connecting the pipe with the rubber part (A), insert the
seal (B) is in place (this part, provided complies with EN549).
Warning: if you use a stainless steel flexible pipe, it must be installed
in such a way that it does not come into contact with moving
cabinetry like drawers or kitchen cupboards and passes at a point
free of obstacles where it can be examined in its entirety.
• After connecting to the gas mains, use soap and water to check
there are no leaks.
Gas connection
9
5019_719_01132_GB 1-06-2007 14:30 Pagina 9

The electrical connections must comply with current
legislation and be carried out by a qualified, competent
person.
•Information on the voltage and power absorbed are shown
on the serial no. plate.
•The appliance must be earthed.
• When installing the appliance, we recommend that this hob
is protected by a 3mm bi-polar switch.
• If damaged, the power cable must be replaced with an
identical type of powercable ( H05V2V2-FT90ºC, or
H05RR-F type). We recommend that this operation be
conducted by our After Sales Service. Please contact our
Customer Care Centre on 00800-3810-4026.
• Do not use extension cables.
• The manufacturer declines all responsibility for damage to
persons, pets or goods as a result of failure to comply with
the regulations above.
Electrical connection
L
Earth
(yellow/green)
N
Important: The following procedure shall be carried out by
competent technical personnel only. The hob can be installed
on different types of materials, such as masonry, metal, bare
wood and heat resistant laminate coated wood (90°C).
Cut an opening in the worktop to the dimensions shown in the
diagram.
Carefully place the seal on the external outline of the worktop, as
shown in the figure below. Apply a light hand pressure to ensure a
good adhesion to the surface.
Fix the hob to the unit, using the fixing brackets provided.
Note: the electrical power cable must be long enough to allow the
hob to be lifted out from above.
Fixing the Hob to the supporting structure. Traditionally fitted
model (Semi Flush fitting).
10
5019_719_01132_GB 1-06-2007 14:30 Pagina 10