Klever Kleena Klassic User manual

HOW TO ADJUST YOUR RETURN LINE WATER FLOW
The water flow from your return line can push the Klever Kleena’s
hose and cause the Klever Kleena to steer away from where the return
line is located, or to remain in one section of the pool. If adjustments
to the existing eyeball return do not allow you to stop the directional
flow from influencing the movement of the Klever Kleena, you should
correct this by purchasing the optional eyeball diverter available from
your Klever Kleena dealer.
TO INSTALL THE EYEBALL DIVERTER
1. Ensure your pool pump is off Remove the original eyeball diverter from
the return line at the pool by unscrewing the lock ring.
2. Replace with the Klever Kleena eyeball diverter.
3. Make sure the opening of the eyeball diverter points to the side, at
a ‘9 o’clock position’.
Usually, directing the return line water flow
against the side of the pool works best.
However, you may want to try pointing the flow
downward or in different positions to see which
works best in your pool.
After installing the eyeball diverter, turn the
pool pump on. the Klever Kleena should begin
moving across the pool floor vacuuming up
debris in its path.
If the Klever Kleena tracks in a repetitive pattern:
• Check the return line water ow and redirect as necessary with a return
line diverter (See “HOW TO ADJUST YOUR RETURN LINE WATER FLOW”)
• Check the Klever Kleena’s hose to ensure it has not become bent or
kinked. (Do not coil the hose. It will retain the coil shape and hinder
the cleaning coverage.) One way to check for kinks in your hose is to
disconnect each hose section and lay them flat on your pool surface
and look down the length of each hose. The hose should be perfectly
straight and float flat. If bends or kinks are present in a sectional hose,
replace those hose sections. The very best performance can only be
obtained using a Kreepy Krauly sectional hose.
• If your Klever Kleena continues to track in a repetitive pattern rotate the
hose from the skimmer box 90 to 180 degrees. This will help correct
any repetitive patterns.
MAINTENANCE
The Klever Kleena requires almost no maintenance. Visually inspect your Klever
Kleena from time to time to make sure that:
1. The flapper is moving freely and is not obstructed by debris.
2. The vacuum pad not excessively worn. (When the traction pads on the
bottom have worn down, it is time for replacement).
3. Manually open and close the Auto Skim valve or KleverSkim Valve to
flush away accumulated dirt and debris to ensure smooth operation. We
recommend that you leave the Klever Kleena in your pool, except during
chemical shock treatments. When swimming it is easy to unplug the Klever
Kleena and pull it to one side. When storing the Klever Kleena, do not
coil the hose. It is best to lay the hose out flat in an area protected from
direct sunlight. Dismantle sectional hose for storage. To ensure optimum
performance from your Klever Kleena, we recommend the use of only
genuine Klever Kleena or Kreepy Krauly sectional hose.
Optimising Performance
Balance your Klever Kleena. The hose weight is used to sink the hose when
the Klever Kleena goes to the bottom of the deep end. The weight should be
adjusted approximately two to three metres from the Klever Kleena. When
the pump is OFF, the Klever Kleena should rest flat on its foot pad on the
bottom of the deep end of the pool.
Check your Klever Kleena’s ability to climb the pool walls. With the pool
pump on, use a pool brush to direct your Kleena Kleena towards a pool
wall. Observe whether the cleaner is able to move from the floor and climb
up the wall. Do this a few times because the cleaner’s steering may initially
turn it away from the wall. the Klever Kleena will require a generous curve to
be able to climb.
If the Klever Kleena climbs the wall:
1. It is normal for your Klever Kleena to climb to the water surface, protrude
its bumper or side above the water, then after a while, turn and move
along or down the wall.
2. If your Klever Kleena comes to the surface and sucks air, check that your
KleverSkim Valve is fitted. If it still sucks air, and you have other intake
points (like a skimmer or floor drain) gradually open the applicable gate
valve to bypass some water from the Klever Kleena. if this still has no
effect, you need to purchase a KleverSkim or inline regulator from your
Klever Kleena dealer.
If the Klever Kleena does NOT climb the wall:
1. Check that your lter and stainer baskets are clean.
2. Check your ltration system gate valves to ensure that all the water is
being drawn through the intake connected to your Klever Kleena.
3. If your suction is weak, call your Klever Kleena dealer in to check your
ltration system or call the Customer Helpline.
4. If you suction is good and your Klever Kleena still does not climb the wall,
the transition radius from the floor to the wall of your pool may be too
small. in this case, you have a square bottom pool. Refer to Section on
Square bottom Pools for further information.
THE KLEVER KLEENA LIMITED WARRANTY
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of
the product which the Customer has under the Trade Practices Act and similar State and Territory
laws. Nothing in this warranty will exclude, restrict or modify any condition, warranty, right or liability
implied in this purchase or protected by law where to do so would render this warranty void. The
purchaser (‘Customer’) has purchased a Klever Kleena automatic inground swimming pool cleaner
(‘Cleaner’) for use in customer’s pool. The Cleaner manufacturer (‘Manufacturer’) hereby provides
the following limited warranty to Customer:
MANUFACTURER WARRANTS THIS CLEANER AGAINST ALL DEFECTS IN MATERIALS AND
WORKMANSHIP FOR A PERIOD OF TWO (2) YEARS FROM THE DATE OF PURCHASE, AND
AGAINST ALL WEAR WHICH AFFECTS THE PERFORMANCE OF THE CLEANER FOR ONE (1)
YEAR FROM THE DATE OF PURCHASE, SUBJECT ONLY TO THE FOLLOWING CONDITIONS
AND EXCLUSIONS:
CONDITIONS & EXCLUSIONS
1. This limited warranty is for the replacement of defective parts only and does not cover labour
charges including, but not limited to, charges incurred for installation of replacement parts or
additional fees which may be imposed by the dealer or servicing agent.
2. All warranty replacement parts are under warranty from the date of purchase of the original
cleaner and not from the date of replacement. All parts purchased thereafter are under
warranty for one (1) full year from the date of purchase.
3. This limited warranty against wear does not include replacement of parts which become
discoloured due to exposure to sunlight or chemicals, or parts which, even if worn, do not
affect performance of the cleaner. Nicks, scratches, fading discolouration, etc. are cosmetic
conditions that do not necessarily affect mechanical performance. Both Manufacturer
and dealer reserve the right to deny any and all warranty claims made for worn parts if
Manufacturer or dealer determine that the wear does not negatively affect mechanical
performance of the cleaner.
4. The Cleaner is designed to function in a properly designed, constructed and maintained
pool. This limited warranty does not extend in the circumstances where the pool’s design,
construction or maintenance is defective or substandard.
5. Deterioration, discolouration or brittleness of pool plaster and vinyl liners can be caused
by age, improper pool chemistry, improper installation, or other factors. Customer hereby
disclaims any and all claims, and releases Manufacturer and Distributor from any and
all claims for damages to any pool surface in the Customer’s pool by reason of the use
and/or operation of the Cleaner. Customer represents and agrees that any claims which it
may assert against Manufacturer shall be limited to those which may be asserted under the
foregoing limited warranty
6. The Cleaner is designed for use in inground pools only and its warranty is limited to this
use. If Cleaner is used in any other application, Customer understands that this is a misuse
of the product and will void all warranty of the Cleaner. Further, Customer hereby releases
Manufacturer from any and all claims stemming from the misuse of the Cleaner
7. Under no circumstances shall Manufacturer be liable for any loss or damage, whether
direct, consequential or incidental, arising out of the use or inability to use the Cleaner in
Customer’s pool.
8. This limited warranty does not apply to any injury, loss, damage, defect, or malfunction
of the Cleaner or failure to function resulting from any failure to operate or maintain the
Cleaner in accordance with the directions contained in the Installation and Operation
Manual or operating instructions provided by the Company for any injury, loss, damage,
defect, or malfunction, or failure to function resulting from any accident, acts of God,
alterations in the Cleaner by anyone other than Manufacturer; or misuse, unreasonable use,
tampering, abuse, acts, omissions, failure or negligence by anyone other than Manufacturer
including but not limited to such damages or injuries to parts resulting from improper
installation, or damage to pump parts resulting from running the pump dry (eg interruption
in or inadequate supply of water to internal pump parts due to loss of prime, or obstruction
in lines or otherwise); or damage, defect or malfunction resulting from defects in, failure or
malfunction of, or negligence, abuse, or misuse with respect to equipment other than the
Cleaner; or any damage or loss of any nature whatsoever and personal injury caused due
to the presence of a foreign object in or about the pool.
9. This limited warranty is valid and enforceable on Klever Kleena Cleaners manufactured in
Australia.
10. This limited warranty is applicable only if the Cleaner is purchased from a Klever Kleena
dealer. If Customer is uncertain as to whether the seller of the Cleaner is a Klever Kleena
dealer, the Customer should call the Klever Kleena State Service Centre immediately after
purchase for verification.
11. This limited warranty shall apply only to Customer as an original purchaser of the Cleaner
from a Klever Kleena dealer and shall not apply to any subsequent purchaser, assignee or
other recipient of the Cleaner from Customer.
12. No dealer or other similar person has any authority to make any warranties or
representations concerning the Klever Kleena or to extend this warranty beyond the express
terms contained herein. Manufacturer assumes no responsibility for any warranties beyond
the express terms contained in this Limited Warranty. The Customer releases and holds
Manufacturer harmless from any claims stemming from any unauthorised representations.
13. This limited warranty shall be void if Customer modies the Klever Kleena System in any
respect including but not limited to the use of parts other than genuine Klever Kleena parts.
14. This limited warranty does not apply unless the Registration Card is signed, completed and
returned within fourteen (14) days from the date of purchase. Manufacturer reserves the
right to dispose of Registration Card once it is received.
15. The foregoing limited warranty gives Customer specic legal rights which may vary from
state to state, and accordingly, some of the listed conditions and exclusions may not apply
to Customers living in certain states.
16. These warranties set forth herein are in lieu of any other warranties, expressed or implied,
including the warranties of merchantability or fitness. Any such implied warranty imposed
by state consumer law is limited in duration to one (1) year from date of purchase.
17. Customer represents and agrees that any claims which it may assert against Manufacturer
shall be limited to those which may be asserted under the foregoing limited warranty.
18. Any dispute between Customer and Manufacturer will be conducted in the State of Western
Australia.
WARNING: Warranty void if label with serial number is removed.
Do not use a one piece manual vacuuming type
hose. These type of hoses coil and restrict water flow and movement
which will hamper the performance of your new Klever Kleena. We only
recommend the use of Kreepy Krauly or Klever Kleena sectional hose.
TROUBLESHOOTING
Because of the individual characteristics of your pool, some additional
adjustments may be required to get the best performance from your
Klever Kleena.
Check these common causes of cleaner problems:
Is filter clean?
Clean filter
Is pump strainer basket clean?
Clean basket
Is debris blocking the bottom intake of the Klever Kleena?
Remove debris (see figure 7)
Are there any leaks in the hose?
Replace leaky section
Is automatic regulator valve free of debris?
Clean valve
Is the main drain closed?
Close main drain valve
If the Klever Kleena is not moving.
• Check to ensure that the main drain and all suction lines are closed,
except for the skimmer box or suction line to which the Klever
Kleena is attached.
• Check for debris in the lter or pump basket.
• Check for debris in the Klever Kleena’s apper. Debris may prevent
the flapper movement or restrict flow.
• Pool pump and lter system may be too small. Consult your pool
professional.
Square Bottom Pools
If the transition radius between the between your pool’s floor and wall is
small and your Klever Kleena is unable to climb the wall, then you have a
square bottom pool. Some square bottom pools (90º floor to wall angle)
may require the use of spacial bumper bar attachment which fits onto the
Klever Kleena swivel. the bumper is not included with your Klever Kleena,
but can be purchased from your Klever Kleena Dealer.
Figure 6
Optional Diverter
EYEBALL DIVERTER (Optional Extra)
WARNING
Front Cover
DESIGNED AND MADE
IN AUSTRALIA
AUSTRALIAN OWNED
Owners Manual
Important
Information
for Pool Blanket
Owners.
See Inside

HOW MANY HOSE SECTIONS DO I NEED?
IMPORTANT: The pump must be on when you check the hose
length. The hose contracts when the pump is operating and will
look longer than when the pump is off.
Position the Klever Kleena at the far end of the pool from the
skimmer box. It is easy to position the Klever Kleena in the pool by
moving it about with your pool brush.
The Klever Kleena’s hose should be long enough to reach the
end of the furtherest corner of the pool plus one extra section.
Save any spare hose sections for use as future replacements.
Welcome
Congratulations on the purchase of your new Klever Kleena, the inground
pool cleaner. You’ll soon see why the Klever Kleena is the smarter choice
in pool cleaning. First, however, you’ll have to install the Klever Kleena
and perhaps make some minor adjustments. This manual covers the steps
needed to install and adjust the Klever Kleena.
Customer Helpline
If you have questions about your Klever Kleena, check the instructions
in this manual first. If you still have questions, call our Customer Service
Department on 1800 777 255. Expert help is available to you from 9:00am to 5:00pm
Monday through Friday. At other times contact your regular pool shop professional.
Activate the Klever Kleena Warranty
You will also need to record the serial number on the Klever Kleena’s warranty
registration card. Complete and return the card to activate the Klever Kleena’s
two year limited warranty. The registration card is self-addressed for your
convenience. the Klever Kleena’s complete warranty is printed on the inside
back cover of this installation and operation manual.
We reserve the right to revise, change, or modify Klever Kleena without incurring
any obligations to make like changes on Klever Kleena’s previous sold. This
publication remains the sole copyright of ITC Manufacturing Pty. Ltd. Written
consent must be obtained before any of its contents are reproduced.
TWIN VALVE AUTOSKIM The unique
automatic “Autoskim” Skimmer valve and
vacuum plate combination ensures full
surface skimming of all floating leaves
and debris. “Autoskim” is available as an
optional extra with the Klever Kleena.
AUTOSKIM INSTALLATION
A Kreepy Krauly Auto Skim (black spring) Combination
Vac/Plate Skim Valve is recommended for superior
performance and continued maximum surface
skimming. Pools with high flow pump and filter systems
are recommended to use a Kreepy Krauly Auto Skim
(black spring) combination Vac/Plate Skim Valve.
Vacuum Plate Adaptor
For all Vacplates except those shown below
please use the threaded fitting to install
your KleverSkim valve. Install the threaded
fitting by screwing it into the vacplate from the top as
shown. Insert the KleverSkim valve tightly inside the fitting.
Making sure the valve can open freely.
Polyplastics Vacuum Plate Adaptor
For the Polyplastic 190 Standard and 210mm
Standard Vacuum Plate (shown left) use the
Vacuum plate and insert the KleverSkim valve
into the fitting, ensuring a tight fit.
Polyplastics Vacuum Plate Adaptor
For the SK1000 Vacuum Plate, simply click the
SK1000 fitting into the vacuum plate and insert
the KleverSkim valve from the top.
STEP 2 HOW TO INSTALL THE KLEVERSKIM
Your KleverSkim Valve is designed to automatically regulate vacuum to your
Klever Kleena to ensure optimal operation. Depending on the Vacuum plate your
pool uses, a different KleverSkim Adaptor will be required.
Ensure the water level of your pool is higher than the KleverSkim Valve to avoid
sucking air or vortexing.
INSTALLATION
The Klever Kleena is designed to work in a wide variety of swimming pools.
That’s why we’ve included certain items with your Klever Kleena. All may
or may not be needed, depending on the particular features of your pool.
The KleverSkim Valve ensures that the Klever Kleena operates at the proper
speed. It automatically adjusts to changes in the amount of water flow to
provide the cleaner with the power necessary to ensure proper cleaning
performance. Excess vacuum not required by the Klever Kleena will be utilised
for Simultaneous Surface Skimming
COMPONENTS CHECK LIST
RECOMMENDED OPTIONS (Not Included)
• Kreepy Krauly Auto Skim Valve (black spring) Combination Vac/Plate Air
Release Valve
• Eyeball Diverter
Sample Vacuum Plate Shown.
Your Vacuum plate may not be the same as this.
How to Connect your Hose
Connect Male to Female
MaleFemale
STEP 1 WHAT TO DO BEFORE
INSTALLING YOUR KLEVER KLEENA
Before assembling and installing your Klever Kleena your pool should be clean and algae-free so as
not to inhibit the cleaner’s traction. If necessary, make the following preparations before proceeding:
1. Chemically balance the pool water.
2. Brush pool and let the debris settle.
3. Hand vacuum thoroughly.
4. Clean pump strainer basket and skimmer basket.
5. Backwash Filter
6. Turn pool pump off.
STEP 3 CONNECTING YOUR HOSE
For Sectional Hose; Complete the assembly of the sectional hose by dampening the hose ends with
water and connecting a female end to the male end of the previous section for all sections with the
male and female end. Allow the hose sections to fill with water before connecting the next section. The
final Sectional Hose to be used should be the special male-male hose section which is used to connect
to your KleverKonecta.
For Kreepy Krauly Continuous Hose; Before using your Kreepy Krauly hose the hose will need to
be relaxed, this can be done by laying the hose flat in a straight line beside the pool on a warm day for
approximately an hour. Alternatively boiling water can be poured through the hose to speed the process
- This should be done with due care.
NOTES: If your pool depth is over two metres, install the hose weight approximately three metres
from the cleaner. The hose weight provided may not be necessary in shallow pools.
WARNING: For optimum cleaning performance, we recommend that you use Klever Kleena or
Kreepy Krauly sectional hose. We cannot guarantee the performance of the Klever Kleena using
your existing sectional or continuous hose.
STEP 4 CONNECTING YOUR CLEANER
Connect the KleverKonecta to the Klever Kleena and place Klever Kleena in
the water and allow it to fill with water before connecting the KleverKonecta
to the special male-male hose.
Your Klever Kleena is now ready to be used. Congratulations.
For the Poolrite plate (shown left) Install
the Threaded fitting from underneath
the vacuum plate and insert the
KleverSkim from the top.
ATTENTION
This optional fitting is
NOT REqUIRED for most
pools. Only use if unable
to connect hose to the
KleverSkim through
the skimmer box
entry.
Serial No. Record Serial
Number Here
How to Connect
your KleverKonecta
Male
KleverKonecta
KleverSkim
KleverSteer
KleverKonecta
Klever Kleena Flexible Hose Connector
Klever Kleena Flexible Hose Connector
Klever Kleena Vacuum Flow Regulator Klever Kleena Vacuum Flow Regulator
Klever Kleena Intelligent Steering System Klever Kleena Intelligent Steering System
Klever Kleena Intelligent Steering System
KleverKonecta
KleverSkim
KleverSteer
KleverKonecta
Klever Kleena Flexible Hose Connector Klever Kleena Flexible Hose Connector
Klever Kleena Vacuum Flow Regulator
Klever Kleena Vacuum Flow Regulator
Klever Kleena Intelligent Steering System Klever Kleena Intelligent Steering System
Klever Kleena Intelligent Steering System
KleverKonecta
KleverSkim
KleverSteer
KleverKonecta
Klever Kleena Flexible Hose Connector
Klever Kleena Flexible Hose Connector
Klever Kleena Vacuum Flow Regulator Klever Kleena Vacuum Flow Regulator
Klever Kleena Intelligent Steering System Klever Kleena Intelligent Steering System
Klever Kleena Intelligent Steering System
KleverKonecta
Special Male-Male Hose
This Special Male-Male hose has
two male connectors and is used to
connect to your KleverKonnecta
ATTENTION POOL BLANKET OWNERS
When a Pool Blanket is in use, carefully monitor your chlorine or salt
water chlorinator settings to avoid over chlorinating your pool which may
damage your Sprinta and void your Warranty.
The Pool Blanket prevents chlorine evaporating reducing the need to add
more chlorine. If you have a salt water chlorinator remember to lower the
amount of chlorine produced when the pool blanket is in use.
If you have any questions please call our Customer Service department
on 1800 777 255 or your local pool shop professional.