Zodiac pH Perfect Guide

Owners Manual and Warranty Information
Please read thoroughly before starting device

Contents
Your pH Perfect has been designed to maintain your pools pH at an ideal balance. Your pools pH
balance is the most important component for water chemistry for your skin, eyes hair etc plus it
also to keeps your sanitiser working at its most efficient. (consider using a Zodiac Chlor Perfect to
work alongside your pH perfect for optimal efficiency)
The pH level is detected by the sensor and then as required corrective solution is injected into the
pool water keeping it safe and healthy
1. Contents of this package
1.1 Identification of parts ........................................................................................................................... 1
1.2 The Control Panel ................................................................................................................................. 2
2. Installation
2.1 Recommendations ............................................................................................................................... 3
2.2 Technical details ................................................................................................................................... 3
2.3 Installation Diagram ..............................................................................................................................4
2.4 Installation of the Sensor POD ........................................................................................................... 5
3. Starting up and operating
3.1 Calibration procedure .......................................................................................................................... 7
3.2 Rule for injecting pH Perfect .............................................................................................................8
3.3 Adjusting the dosage depending on alkalinity................................................................................ 9
4. Adjustments: “Settings” menu
4.1 “Settings” menu - Default parameters ...........................................................................................10
4.2 Language ...............................................................................................................................................10
4.3 Set point ................................................................................................................................................10
4.4 Type of dosage ......................................................................................................................................11
4.5 Alkalinity level ....................................................................................................................................... 11
4.6 “OFA” over-feed protection ................................................................................................................11
4.7 Detection that filtration is in progress ...........................................................................................12
4.8 Resetting the appliance .....................................................................................................................13
5. Care and maintenance of your pH Perfect
5.1 Changing the peristaltic pump tube ...............................................................................................13
5.2 Winterising the pH Perfect ................................................................................................................13
6. Water quality ...............................................................................................................................................14
7. Alarms ...........................................................................................................................................................14
8. Problem solving ..........................................................................................................................................15
9. Warranty .......................................................................................................................................................16
10. Online registration ....................................................................................................................................17

1
Contents
1. Contents of this Package
The symbol indicates important information that must imperatively be taken into
account in order to avoid risk of injury to persons or damage to the appliance.
The symbol indicates useful information.
1.1 Identification of parts
1. Control box
2. Mounting bracket and screws
3. Hole saw
4. Tubing
5. POD assembly
6. POD locking ring
7. pH sensor
8. pH sensor cable
9. Sensor calibration fluid
10. Anti Fume Cap 5lt and 15/20lt
10 9
7
8
1
4
6
5
3
2

2
1.2 The Control Panel
Blue Backlighted LCD 1 line 16 white character screen.
Left side warning zone (alarms) / Right side pH display
Peristaltic pump
Connection for injection tube.
Connection for suction tube
BNC socket for connecting the pH sensor:
The sensor cable is connected to the regulator unit with this connector
Master switch: for powering the control unit
Navigation button “q” for navigating in the menu
SET/Esc” button: button for exiting from the menu;
also for displaying the pH set point when pressed continuously
Navigation button “p” for navigating in the menu
“CAL/Enter” button: button for enabling the sensor calibration mode
(the button must be pressed for 5 seconds).
This is also used for accepting changes in the menu











3
2. Installation
2.1 Recommendations
Warning: pH Perfect must be installed by an experienced pool professional.
Before carrying out any installation or maintenance of the pH Perfect control centre, disconnect it
from the mains power supplies.
Before starting to install the pH Perfect, check that you have all the components listed above and
ensure you read this instruction manual carefully.
This appliance is not intended for use by persons (including children) that lack experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a responsible person.
Children should be supervised to ensure that they do not play with the device.
The installation of this device should be carried out by a qualified person in accordance with the
Australian wiring rules AS/NZS 3000.
The control centre should be located in the correct pool zone and connected to supply via a power
outlet that is protected by a residual current device (RCD) having a rated residual operating current
not exceeding 30mA.
The power outlet should have a degree of protection suitable for the pool zone
Ensure that equipotential bonding of all parts of the pool installation is carried out.
During the installation phase of the pH Perfect, check the following:
• that the voltage of the power supply corresponds to the voltage indicated on the side of the
appliance
• that the injection point pressure is lower than 1.5 Bar
• that the peristaltic pump's protection cover is correctly fitted
• that the suction tube is immersed in the corrective solution (pH up or down) container with the
suction tube also connected to the peristaltic pump (left side).
• that the injection tube is connected on one side to the peristaltic pump (right side) and on the
other side to the pool return pipe via the injection valve.
Zodiac Group Australia Pty Ltd will not be held liable for the use of this device with inappropriate
products.
The pH sensor is fragile, it must be handled with care. Try to avoid touching the tip with your fingers.
2.2 Technical details
Dimension (L - W - H) 240 x 200 x 90mm
Weight (appliance, sensor, tube and pipes) 1.7 kg
Power feed 50Hz 220-240 V AC/50 Hz
Consumption 12W
Pump flow rate 1.5 l/hr
Maximum back pressure 1.5 bar
pH control range 0.0 pH-14.0 pH
Appliance accuracy +/- 0.1 pH
Calibration of the sensor 7.5 pH
If the supply cord is damaged, it shall be replaced by the manufacturer or its
service agent, or similarly qualified person in order to avoid a hazard.

4
2.3 Installation Diagram
Installation of the pH Perfect on the filtration system:
It is recommended that pH Perfect be installed after the filter (and any heating
device) but before the salt chlorinator cell... if no salt chlorinator is installed it
should be the last device on the return line
Hydraulic Diagram Your pH sensor is a very delicate product
and can be affected by external forces
such as stray electrical current from
other devices.
When connecting the sensor into position
try to keep the cable away from other
power leads
The maximum pressure in the pipes must
not be greater than 1.5 Bar. In order to
extend the life of the peristaltic tube, the
pressure should not exceed 1 bar
Install the pH Perfect control centre
using the supplied fixing kit on a rigid
support (a vertical wall) in an easy to
access location.
Electrical connection
If you are using an external timer
to control your filter pump please
plug the ‘piggyback’ plug located on
the pH Perfect into the timer and
then plug the filter pump into the
piggyback plug. This will create a
controlled time circuit for pH Perfect
with the filter pump.
Now connect the pH Perfect power
plug into a power point to power the
unit up
Electrical Diagram
Warning:
- Acid fumes are highly corrosive
- Do not store acid directly underneath the control unit
- It is preferable to store acid in a safe place outside the filter shed
- If storing inside ensure adequate ventilation is provided

5
2.4 Installation of the Sensor POD
1. Use a straight section of horizontal pipe located past
all other equipment including pump, filter, heater etc
(30 cm long is best).
2. POD should be installed so that once the sensor is
fitted it is in an upright position
3. Disassemble sensor POD to get lower part of POD
clamp with 2 holes (picture 1).
4. Place the lower part of POD clamp upside down into
position on the selected length of piping.
5. Now mark the location of the 2 holes to be made into
piping using a pencil or marker (picture 2).
6. Drill the 2 holes using the provided hole saw. Ensure
that holes are perfectly smooth around the edges
(picture 3).
7. Position the upper part of POD clamp by sliding it into
the 2 previously drilled holes
 NOTE: arrows on upper part of POD clamp
indicate direction of water flow
8. Interlock the lower part of POD clamp onto the upper
part already in place on piping. (picture 4).
9. Fit the POD cap on top of upper POD clamp, re-fit
locking ring and tighten firmly using provided tool
ensuring the locking ring thread is seated properly
before tightening.
10. Install sensor into position by firmly screwing into the
POD cap in the space allocated. (use Teflon tape on
thread)
11. Connect the sensor with the provided cable to the
control box.
Injection tube fitted
to one way valve
Sensor fitted in POD
1
2
3
4

6
1. To connect the suction and injection tubes please
‘soften’ the ends of the tubing by immersing in
warm water for a few minutes.
2. Remove the small face panel that covers the
peristaltic pump to reveal the screw fittings
underneath (see picture A)
3. The suction tube is connected to the left hand side
of the peristaltic pump fittings.
4. Use a length of tube long enough to reach from
the liquid container to the control box and feed
the tube through the black rubber grommet in
the ‘anti-fume’ cap (2 sizes are included 5lt and
15/20lt).
5. Once the cap is on the tube, now fit the small
ceramic weight on the suction tube and then fit
the small blue barb fitting to the end of the tube to
prevent the weight from falling off. (see picture B)
6. Now connect the injection tubing to the injection
side (right hand) of the peristaltic pump
7. Then fit the other end of the injection tube to the
one way valve located in the sensor POD (this is the
injection point for the solution being delivered) (see
picture C)
8. Once all connections are made place the suction
line into the container and screw the anti fume cap
down into position. (see picture D)
Please note: When installing pH Perfect ensure your
acid is diluted to a 50/50 mix of acid/water before
screwing the cap down
Now the POD is in place and the sensor is connected it is time to connect the suction and
injection tubes
A
B
C
D

7
3. Starting up and operating
3.1 Calibration procedure
The sensor must be calibrated when your pH Perfect is first installed and ideally
every two months there after to obtain the best operating conditions.
Calibration must be done each time your pool is restarted at the beginning of the season.
The calibration procedure is carried out when filtration is stopped thanks to its double supply (the
appliance remains powered on). Before calibrating, stop filtration and close the valves so as to isolate
the pH sensor holder from flowing water.
Procedure
1. Fill a bottle with clean water(tap water).
2. Undo the sensor holder and remove the sensor from the pipe.
3. Rinse the sensor in the bottle. Then shake gently to remove excess water.
4. Pour a small amount of pH 7.5 calibration fluid into a small bottle (enough to cover the end of the
sensor tip). Then immerse the sensor into the fluid. Discard the used calibration fluid after use so as
not to contaminate the rest of the bottle.
5.
6.
After 30 seconds, the appliance
indicates the measurement
reliability of the sensor
expressed as a percentage.
7.
To finish calibration, press the “CAL” button.
The instrument will return to measuring mode.
Once the calibration is complete install the
sensor in the location provided in the POD
Keep the “CAL/Enter” button
pressed for more than 5
seconds until “Calibration”
appears on the LCD screen (5a).
Press the “CAL/Enter” button
again as indicated on the screen
for calibration on pH7 (5b).
an automatic progression bar
then appears (5c). Keep the
sensor immersed in the buffer
solution for 30 seconds.
5a 5b 5c

8
• Once the calibration is complete, your pH Perfect is ready to regulate your
pool automatically.
• If your water chemistry is badly out of balance please bring your pool pH
within balance before activating the pH Perfect.
 The pH Perfect peristaltic pump is self-starting. However, it is possible to operate it manually by
keeping the ”p“ Navigation button pressed.
The peristaltic pump will then inject corrective solution as long as the button is pressed.
3.2 Rule for injecting pH Perfect
Proportional cyclic dosing - exclusive to Zodiac
• To reach the set point in the best possible conditions (the quickest, but with the least possible
corrective solution), your pH Perfect automatically detects the difference of the pH value measured
in the pool compared with the desired set point (default value = 7.4 pH).
• This proportional injection is cyclic and the cycle time is 10 minutes. What will change in dosing is the
different times of injection and pause. The proportions are adjusted automatically and the different
dosages are distributed in steps of 0.15 pH.

E.g.: For 4 cycles with a set point of 7.4 pH and acid regulation (standard alkalinity levels) :
pH ≥7, 5 5 : 20% injection (2 minutes) & 80% pause (8 minutes)
pH ≥7,70 : 50% injection (5 minutes) & 50% pause (5 minutes)
pH ≥7, 8 5 : 75% injection (7 minutes 30 seconds) & 25% pause (2 minutes 30 seconds)
pH <7,9 0 : 100% injection (10 minutes, continuous)

9
3.3 Adjusting the dosage depending on alkalinity
Water’s pH is potentially unstable. Its stability depends on the alkalinity of the water (also called total
alkalinity). If the total water hardness is low (< 100 ppm), the pH will be potentially unstable and it will be
the opposite if the total water hardness is high (> 150 ppm).
In order to always have an optimal balance, the pH Perfect has a function making it possible to adjust
the quantities of potentially injected corrector product depending on the total water hardness (see
paragraph 4.5).
The injection rule is, of course, inversed if alkaline dosing is chosen.

10
4. Adjustments: “Settings” menu
4.1 “Settings” menu - Default parameters
The pH Perfect is factory preset with the following settings (suitable for most cases):
a. Set point: pH = 7.4
b. Dosage = acid (injection when the pH is higher than the set point)
c. Alkalinity level = standard
d. “OFA” over-feed protection: 4 hours
e. Calibration
f. Detection that filtration is in progress: enabled
 To access the “Settings” menu, the appliance must be ON.
Simultaneously press the “CAL/Enter” and “SET/Esc” buttons for
about 5 seconds until the LCD screen displays “Settings” (A).
This “settings” menu gives access to the following adjustments:
Language
Set point
Type of dosage
Alkalinity level
Time before triggering the “OFA” over-feed protection
Type of calibration
Detection that filtration is in progress
 To exit the “Settings” menu, press the “SET/Esc” button and
select “Yes” or “No”, using the “p” and “q” navigation buttons to
save the new settings or not. Accept the choice by pressing the
“CAL/Enter” button (B).
4.2 Language
You can choose between 6 languages for the LCD display:
French, English, German, Spanish, Italian and Dutch.
To change language when in the “Settings” menu, enable the option
list by pressing the “CAL/Enter” button (a small arrow appears on the
right of the screen and the language message flashes).
Then select the language using the “p” and “q” navigation buttons.
Accept the choice by pressing the “CAL/Enter” button.
4.3 Set point
The default set point on the pH Perfect is 7.4 pH (D)To change it when in
the “Settings” menu, enable the option list by pressing the “CAL/Enter”
button (the pH value fl ashes). Then select the value chosen using the
“p” and “q” navigation buttons. The adjustment is made in increments
of 10 mV. Accept the choice by pressing the “CAL/Enter” button.
C
A
B
D
It is also possible to directly access the set point by holding down the “SET/Esc” button
(keep pressing while changing the setting using the “p” and “q” navigation buttons).

11
4. Adjustments: “Settings” menu
4.4 Type of dosage
The default dosage on the pH Perfect is acid
(injection of pH minus) (E).
To change it when in the “Settings” menu, enable the option list by
pressing the “CAL/Enter” button
(a small arrow appears on the right of the screen and the type of
dosage flashes). Then select the dosage using the “p” and “q”
navigation buttons.
Accept the choice by pressing the “CAL/Enter” button.
4.5 Alkalinity level
The quantity of corrective fluid potentially injected can be modified to take into account the alkalinity of
the water (total water hardness).
To change the value of total water hardness, from the « Settings » menu, activate the choice list by
pressing the “CAL/Enter” key (a small arrow appears on the right of the screen) then select the level
using the “p” and “q” navigation keys.
Validate by pressing the “CAL/Enter” key.
 Indication of the choice of alkalinity level:
• TAC < 100 ppm = Low
• 100 < TAC < 150 ppm = Std (Standard = default setting)
• TAC > 150 ppm = High
4.6 “OFA” over-feed protection
Your pH Perfect is equipped with protection to prevent over-feeding
in the event there is a problem with the pH sensor, for example. The
purpose of this protection, called “OFA” (Over Feed Alarm), is to pause
the appliance if it has not reached the set point at the end of the time;
set by default at 4 hours (F).
The “OFA” over-feed protection functions in 2 steps:
#1: “OFA alarm” flashes on the LCD screen after 70% of the OFA
programmed time has been used without reaching the set point.
However, the appliance continues running.
#2: “Stop OFA” is displayed on the LCD screen after reaching 100%
of the OFA programmed time
(4 hours in the original setting). The appliance is then safe.
 To cancel this protection and start your pH Perfect, press the “CAL/Enter” button (possible on the
2 steps of the OFA alarm).
E
F

12
Make sure that the pH sensor is in good condition. If necessary, clean and/or
recalibrate it.
The over-feed protection is set by default for a maximum time of 4 hours.
It is possible to adjust it from “OFF” (disabled) to “6 hours” by intervals of 1 hour.
A fairly high setting is strongly recommended to avoid any inopportune and/or
unjustified start.
To regulate the OFA when in the “Settings” menu, enable the option list by pressing the “CAL/Enter”
button (the value in hours flashes). Then select the value chosen using the “p” and “q” navigation
buttons.
The adjustment is made by intervals of 1 hours.
Accept the choice by pressing the “CAL/Enter” button.
 Special functions of the OFA
To prevent “false” alarms just after installing a pH Perfect (if the pH is poorly balanced and the chlorine
needed therefore high), the OFA may be temporarily disabled for 24 or 48 hours:
• Presser Press “p” & “q” & “CAL”: OFA disabled for 24 hours
(automatically re-enabled).
• Presser Press “p” & “q” & “SET”: OFA disabled for 48 hours
(automatically re-enabled).
4.7 Detection that filtration is in progress
Your pH Perfect is equipped by default with a double power feed for keeping the appliance live in order
to calibrate the pH sensor when filtration is stopped.
However, it is possible to disable this function if the electrical connection is different (work done by a
professional).
The pH Perfect no longer takes into account whether filtration is in progress and
is likely to inject corrective solution when there is no flow in the pipes.
Disabling is only possible if the mains power cable is controlled by the filtration.
To change this function when in the “Settings” menu, enable the
option list by pressing the “CAL/Enter” button (a small arrow appears
on the right of the screen and the status of detection of filtration
flashes). Then select “ON” or“OFF” using the “p” and “q” navigation
buttons (G). Accept the choice by pressing the “CAL/Enter” button.
G

13
4.8 Resetting the appliance
In the event of incorrect manipulation, it is possible to restore all the original pH Perfect functional
settings.
Procedure for resetting the pH:
Switch OFF the appliance.
Switch ON the appliance by pressing simultaneously on the two “p” and “q” navigation buttons
(keep the buttons pressed until the message appears on the screen).
Select “Yes” or “No” using the navigation buttons, then accept using the “CAL/Enter” button.
All the factory settings will then be restored.
5.1 Changing the peristaltic pump tube
1. Remove the protective
cover carefully drawing
it towards you.
4. Position the tablet holder on “10:20” turning clockwise.
Insert the left-hand connection in its housing, then
pass the tube under the guide of the tablet holder.
Turn the tablet holder clockwise and at the same time
put the tube into the pump head up to the right-hand
connection.
5. Replace the
protective
cover (place
the pin in the
attachment
hole).
2. Position the tablet
holder on “10:20”
turning clockwise.
3. Fully release the left-hand
connection keeping it stretched
outwards, then turn the tablet
holder clockwise in order to free
the tube up to the right-hand
connection.
5.2 Winterizing the pH Perfect
 When pH Perfect has to be winterised, it is advisable to pump clean water through it in order to rinse
the peristaltic pipe using the self-priming function and pressing the navigation button “p”
(see paragraph 3.1).
Next turn the tablet holder to “6:00”.
These two precautions will make it easier to restart the appliance.
Remove the pH sensor from its holder. Store it in its original cap or a cup filled with tap water. If
necessary plug sensor holder.
Never leave the end of the sensor out of water!
5. Care and maintenance of your pH Perfect

14
7. Alarms
6. Water quality
Even though pH Perfect is an automated delivery device it is still a requirement
to have the pool water regularly checked for balance and chemistry.
See the table below for recommendations of frequency
Zodiac Group Australia cannot be held liable if these rules are not followed.
pH Free Chlorine
mg/L or ppm
TA
(alkalinity or buffer
effect)°f (ppm)
CH
(level of calcium
carbonate
°f (ppm)
Cyanuric Acid
(stabiliser)
mg/L or ppm
Recommended
Values 7.2 – 7.8 0.5 – 2.0 (80 – 300) (90 - 300) 30 - 50
To increase
Use pH Perfect
in “alkaline”
dosage and/
or increase
setpoint
Add chlorine
(manually or
with an ORP
regulation)
Add sodium
bicarbonate
Add calcium
chloride
Add cyanuric
acid (only if
necessary)
To reduce
Use pH perfect
in “acid”
dosage and/
or decrease
setpoint
Stop adding
chlorine
Add diluted
hydrochloric
acid
Add a scale
fixer or
carry out
decarbonatation
Partially empty
the pool and
refill it again
Test Frequency Weekly Weekly Monthly Monthly Quarterly
Alarm Cause(s) Solutions
The container of corrective
solution is empty Replace the container
First OFA step enabled
(time > 70%)
Check pH value
Press “CAL/Enter” to stop the alarm
Second OFA step enabled
(time = 100%)t
Check pH value
Press “CAL/Enter” to stop the alarm
Filtration stopped Start filtration pump
Check the connection
Buffer solution ineffective
pH sensor defective
Replace the buffer solutions
Clean and/or replace the pH sensor
Parameter error Press “CAL/Enter” to cancel the fault
Call your local pool professional

15
7. Alarms
6. Water quality
8. Problem solving
Problem Cause Remedy
Displayed pH
level doesn't
seem to change
Problem with cable and/
or connector
Make sure that the sensor-pH Perfect
connection is not short-circuited (between
the central core of the cable and the exterior
sheathing)
Make sure that there is no moisture and/or
condensation around the BNC socket
The appliance
always
displays a high
value or the
measurement
is constantly
unstable
The electrode connection
cable is damaged Check the cable and/or the BNC socket
The pH sensor has an air
bubble in the bulb
Put the sensor into upright position and shake
gently so that the air bubble rises back up to the top
Note: The sensor should be fitted in a vertical
position or at an angle no greater than 45°
The pH sensor is worn Replace the pH sensor
The sensor cable is too
close to a power cable
causing interference
Reduce the distance between the appliance and the
sensor and/or place the cable elsewhere
Impossible to
calibrate
(error message)
Quality of
calibration of
the pH sensor
< 25%
Buffer solution is
ineffective
Make sure that the solution hasn't expired
Check the pH buffer solution with a pH electronic
meter
Check the pH buffer solution with a pH electronic
meter
Problem with the sensor’s
porous element, dirt
deposits
Make sure that the electrode bulb is in good
condition, that it has not been allowed to dry out
of the water. As a last resort, clean by soaking the
electrode in a 10% hydrochloric acid solution
Check that the porosity of the sensor is in good
condition (wash the sensor in an acid solution).
The pH sensor is worn Replace the pH sensor
Slow response
from the pH
sensor
Static electricity on the
pH sensor
During the calibration phase DO NOT WIPE the pH
sensor with a cloth or paper, but after rinsing, shake
it gently

16
9. Warranty
Express Warranty and Guarantees
Zodiac Group Australia Pty Ltd (Zodiac Australia) warrants that the Zodiac pH Perfect (Product) will be
free from defects in materials and workmanship for a period of 2 years from date of purchase.
Terms & Conditions
1. This express warranty only applies if the Product has been purchased from a dealer authorised by
Zodiac Australia to supply it (Authorised Dealer). Purchase from an Authorised Dealer ensures that
the product is a genuine Zodiac product, that it is the version designed for Asia Pacific conditions,
and that the Purchaser has access to appropriate technical knowledge and advice.
2. Zodiac Australia's liability under this express warranty is limited, at its option, to the repair or
replacement of the Product or the payment of the cost of having the Product repaired or replaced.
3. This express warranty does not apply in the following circumstances:
(a) if the Product has not been installed in accordance with Zodiac's installation instructions;
(b) if the Product has been modified other than as authorised by Zodiac Australia or if a component
part has been replaced by a part that is not a genuine Zodiac product;
(c) if a defect results from use of the Product outside recommended operating conditions; or
(d) if a defect results from damage (including damage to any internal electronics) caused by a
power surge or lightning strike.
4. Without limiting 3 above, products sold by Zodiac Australia are designed for use with swimming pool
water balanced in accordance with Australian Standard AS3633–1989 with a pH range of 7.0 – 7.8.
Maximum chlorine readings should not exceed 4ppm. Where pool water is not maintained within
these parameters, Zodiac Australia will not be responsible under this express warranty for any
resulting damage, including damage caused by corrosion, scaling or stress loading.
5. Replacement parts supplied under this express warranty are warranted to be free from defects in
materials and workmanship for the remainder of the warranty period or for 12 months from the
supply of the replacement, whichever is longer.
Product warranty registration
6. Purchasers should register their Products as soon as conveniently possible after purchase by
completing a Product Warranty Registration Form and posting it to Zodiac Australia at the address
shown on the Form or by registering online at www.zodiac.com.au.
7. Product registration must occur, and proof of purchase must be received by Zodiac Australia, prior
to any warranty work being approved. Where applicable, a serial number, installation date and name
of installer is required as part of the registration process.
How to make a warranty claim
8. The Purchaser must telephone or email Zodiac Australia Customer Service and obtain a warranty ID
number for the warranty claim. Contact details are:
Zodiac Group Australia Pty Ltd Customer Service
219 Woodpark Road
Smithfield NSW 2164
Telephone: [phone]
Email address: [e-mail]

17
9. Warranty
9. Zodiac Australia reserves the right to determine, in relation to each warranty claim, whether the
Product should be returned to the Authorised Dealer at the address where the Purchaser purchased
the Product or whether warranty service will be provided in the field, repaired at a Zodiac workshop
or at the premises of an authorized Zodiac warranty agent.
10. If it is necessary for the Purchaser to incur freight charges in making a valid claim under this
warranty, Zodiac Australia will reimburse the Purchaser for charges reasonably incurred upon proof
of the charges.
Additional guarantees, rights and remedies
Australian Purchasers – Guarantees under the Australian Consumer Law
11. The benefits of this express warranty are in addition to other guarantees, rights and remedies
Australian consumers have under the Australian Consumer Law.
12. Zodiac Australia products come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Purchasers in other Countries
13. The laws and regulations of other countries may confer on Purchasers in those countries additional
rights and remedies. To the extent that they cannot be excluded or modified, Purchasers have the
benefits of those rights and remedies in addition to the benefits of this express warranty. To the full
extent that it is permissible to do so, those additional rights and remedies are excluded or modified
so as to be consistent with Zodiac Australia's express warranty.
INCONSISTENCY WITH WARRANTY STATEMENTS IN PRODUCT MANUALS
OR OTHER DOCUMENTS ACCOMPANYING PRODUCTS
If any warranty statements in a Zodiac Australia product manual or other document are inconsistent
with the above Express Warranty and Guarantees, the above overrides and replaces the inconsistent
statements.
10. Online registration
Registration on line
Register your product on our website:
• you will be the first to be informed of new Zodiac products and special offers,
• You can help us to constantly improve the quality of our products.
Australia – New Zealand www.zodiac.com.au

Zodiac is a registered trademark of Zodiac Group Australia Pty Ltd
ABN 87 002 641 965
ZODIAC CUSTOMER SERVICE CENTRE
Zodiac Group Australia:
219 Woodpark Rd, Smithfield,
NSW 2164 Australia
Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.zodiac.com.au
Due to constant developments and improvements,
specifications may change without notice.
Improper use could affect performance and void warranty.
© Copyright Zodiac Australian Ltd 2016
Your Retailer