KLINGER 15-5800VT User manual

5.8GHz WIRELESS A/V/ALARM TRANSMITTER USER MANUAL
MODEL: 15-5800VT
1. Panel View
○
1○ 2○ 3○ 4○ 5○ 6○ 7○ 8○ 9○
10
1. DC+12V IN: Power input DC+12V/1.5A.
2. DC+12V OUT: DC+12V/750mA for box camera only, and with a over current protector.
(Note: If you don’t use this port for cameras, you can use the DC+12V/500mAadaptor.)
3. ALARM IN: Once triggered, the built-in buzzer rings on for a 20-sec time. This port could be connected to
alarm sensor, e.g.: PIR Detector, Magnetic Reed Switch Detector.
4. AUDIO IN: RCAfemale for input video signal.
5.
6VIDEO IN: BNC female for input audio signal.
. POWER/State LED: Indicated to power on and ARM status.
Indications Power/State LED
Power On On
ARM High speed Flashing
ra7. DISARM: DISARM at 15-5800VT/15-5800VH t nsmitter’s side only.
on.8. CH SELECT (AB C D): 5.8GHz transmission channel selecti
9. IDAND ALARM MUTE: ID address setting is use for paring with 15-5800VR receivers. It must be make the
same code setting to link transmitter and receiver each other. The alarm mute function is use for muting
built-in buzzer at 15-5800VT/15-5800VH side only.
Bit 1 Bit 2 Bit 3 ID Address
(Pairing with RX) Bit 4 Alarm Mute
0 0 0 0 0 ON
0 0 1 1 1 OFF
0 1 0 2
0 1 1 3
1 0 0 4
1 0 1 5
1 1 0 6
1 1 1 7
(1 W O 0 = SW OFF)= S N,
10. ANT: RP-SMAconne r for connec ntenna.
REMARK: When the frequ nels have the inte rence, adjust antenna or change the channel of
transmitter and don’t close 802 a/b/ P router a other 5.8GHz devices.
(Note: Please keep 3 ~ 5 meter a y)
cto ted to 5.8 GHz a
ency chan rfe
to .11 g A nd
wa

2. Caution for Installatio
.1 Be careful, never let any water in this equipment. the dust.
.3 Be extra careful not to shake the unit.
sure to unplug the unit and contact your local dealer.
tion CH3 CH4 CH5 CH6 CH7 CH8
n
2
2.2 If necessary, use a soft cloth moistened with alcohol to wipe off
2
2.4 Avoid places where temperatures exceed 50 o C or higher.
2.5 Avoid places where there are frequent vibrations or shocks.
2.6 When any abnormalities occur, make
3. Packing
3.1Transmitter ×1
3.2 Antenna ×1
3.3Usermanual ×1
3.4 Screws ×4
3.5 Plastic-Conical-Anchor ×4
3.6 Power Adaptor ×1 [Option]
4. Specifica
CHANNAL CH1 CH2
FREQUENCY 5740 5760 5780
MHz 5800 MHz 5820 MHz 5840 MHz 5860 MHz 5740 MHzMHz MHz
RF ANT. IMPEDANCE 50 ΩTypical
POWER DC12V/1.5AAdaptor
CURRENT 350mA
DC OUTPUT DC12V/750mA
OUTPUT POWER 10mW
VIDEO INPUT 1 C site 0ΩVp-p ompo @ 5
AUDIO INPUT 2 Vp-p @ T600Ωypical
ALARM INPUT T MO ectiTL/C S (Level Det on)
DIMENSIONS L:85 mm H:30 mm D:16 mm
FCC Part 15 Notice:
been tested and found to a Class B digital device, pursuant to
FCC rules. These limits ar easonable protection against harmful
residential installation. This and c radio frequency
nergy and, if not installed and used in accordance with the instructions, may cause harmful interference to
r, there is no guarantee that interference will not occur in a particular
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
ure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
to this device that are not expressly
This equipment has comply with the limits for
part 15 of the e designed to provide r
interference in a equipment generates, uses an radiate
e
radio communications. Howeve
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
transmitter.
2. This equipment complies with FCC RF radiation expos
centimeters between the radiator and your body.
3. Any changes or modifications (including the antennas) made
approved by the manufacturer may void the user’s authority to operate the equipment.
Q2009/06/06