KMART Side Drawer Oak Look 42619673 User manual

9
2
4
6
1
10
11
11
11
11
7
8
5
3
Hardw
are list
4x12mm
75x73x14mm
6x30mm
4x35mm
4x14mm
20x150mm
A
B
C
D
E
F
G
H
6 x 35 mm
15 x 9.5 mm
6 x 30 mm
4 x 40 mm
4 x 30 mm
8 PCS
8 PCS
4 PCS
1 PCS
1 PCS
20 PCS
4 PCS
4 PCS
1
234
567
89 10
11
2
1 PC
1 PC 1 PC 1 PC
1 PCS1 PCS
1 PCS
1 PCS 1 PCS 1 PC
4 PCS
Assembly Instructions
CARE INSTRUCTIONS:
TO BE ASSEMBLED ON A CLEAN, DRY AND SMOOTH SURFACE. WIPE CLEAN WITH A SOFT DAMP CLOTH. NEVER USE SCOURERS, ABRASIVES OR CHEMICAL SOLVENTS. CHECK AND
TIGHTEN ALL PARTS REGULARLY. KEEP AWAY FROM MOISTURE AND DIRECT SUNLIGHT. STORE IN A DRY PLACE. FOR INDOOR USE ONLY.
WARNING!
DO NOT STAND, SIT OR LEAN ON THIS UNIT. DO NOT USE THIS UNIT AS A STEP LADDER OR AS A CHOPPING SURFACE. ENSURE THIS UNIT IS USED ONLY ON A FLAT SURFACE. DO NOT
USE THIS UNIT UNLESS ALL BOLTS AND SCREWS ARE FIRMLY SECURED. DO NOT PLACE HOT ITEMS SUCH AS COFFEE CUPS DIRECTLY ON THE SURFACE OF THIS FURNITURE ITEM. KEEP
AWAY FROM CHILDREN AND BABIES. THIS PACKAGE CONTAINS SMALL PARTS AND SHARP POINTS. ADULT ASSEMBLY REQUIRED. A MILD ODOUR MAY BE PRESENT WHEN FIRST OPENING
THIS CARTON. SIMPLY ALLOW TO AIR OUTSIDE AND THIS WILL FADE. MAXIMUM SAFE LOAD: 10KGS FOR TOP PANEL, 5KGS FOR INSIDE DRAWER.

A
A
B
A
4
3
1
A
A
A
A
B
B
B
C
C
C
C
2
1
3
10
4
10
1
3
4
H
H
G
G
G
G
H
H
4
2
Step 1: Fix the screws from Part A onto board 1 , and put Part B into
the corresponding position (as per below diagram). Attach board 3 &
4 to board 1 , and then fix the round screws from Part A with a
screwdriver. Ensure all parts align.
Step 2: Slide board 10 into the corresponding position (as per below
diagram). Ensure it is fully fitted in the groove.
Step 3: Put part B in corresponding position (as per below diagram),
Attach board 2 with screws (Part C), using a screwdriver.
Step 4: Fix Part H onto board 2 with screws (Part G).

11
11
11
11
10
D
D
7
89
6
A
A
A
5
Step 5: Screw the legs (Part 11 ) into Part H from step 4.
Step 6: Assemble board 6 , 7 , 8 with screws (Part D). Slide board 9
into corresponding position (as per below diagram). Ensure it isfully
fitted in the groove.
Step 7: Fix the screws from Part A onto board 5 . Attach this piece
to the part from step 6 (as per below diagram), and then fix the round
screws from Part A with a screwdriver. Ensure all parts align.
Step 8: Slide the drawer into the unit. Assembly is complete.
Note this drawer comes with wall fixing attachments ( E & F ).
Please use if you want to secure this drawer to the wall.