Kodicom DigiNet Center User manual

KODICOM
KODICOM
DigiNet
DigiNet
DigiNet Center(v4.11)
User Guide

Center Program?
Center Program?
It’s a program that enables you watch and control the site DVR. Therefore, you don’t need a
DVR to watch site DVR’s image.
System spec.(recommended)
System spec.(recommended)
►CPU : Celeron 433MHz over
►MEMORY : 64MB over
►VGA CARD : AGP 16MB over
►HDD : 100MB over
►O/S : Windows98 SE / Windows ME / Windows 2000 / Windows NT
►Communication : MODEM, LAN, ISDN, Leased Circuit
►DirectX : v7.0 over

Contents
When you purchased DigiNet Center program, make sure that the following contents
are Included.
DigiNet Center Program User manual

1
1. CONNECTION……………………...………………………………………..7
1.1 ISDN, DSU CONNECTION....…………………………………………..7
1.2 MODEM, LAN CONNECTION……………………………...………….8
2. Center program installation…………...….………………………………9
3. Center program execute…………….…………………………..……….12
4. Main screen setup………………………………………………………...13
5. Center setup…………………….………………………………...……….14
6. How to connect to Site DVR……….……………………………………18
6.1 Connection on LAN………………………...………………………..…19
6.2 Connection on PSTN,ISDN……………………………………………21
7. Playing current image …………………………………………………...24
8. Change to search mode ……………………....……………………..….25
8.1 Date and time select for searching …..………………………………26
8.2 Camera selection ……………………………………………………..27
8.3 Replaying searched image ………………………....…………………28
8.4 Book mark ……………………………………………………………….31
8.5 Search screen zooming in/out and moving………………………......32
8.6 Search screen quality improvement ………………………………...33
8.7 Audio play ………………………………………………………………..34
8.8 Data backup ..………..…………………………………….……………35
8.9 Printing searched image …………………………………........………44
9. Selection between PAN/TILT & surveillance mode………………...46
9.1 Control of PAN/TILT mode………………………………………...….47
10. Site DVR setup.…………………………………………………....…….48
10.1 Hardware setup……………………………………………………….49
10.2 Motion detection setup……..…………………………………………53
10.3 Recording Schedule setup ………………………………………….56
10.4 Site information………………………………………………………..60
10.5 System setup…………………………………………………………..61
10.6 Other......………………………………………………………………..66
11. Searching backup data ………………………………………………..67
11.1 Search mode conversion……………………………………………...69
11.2 Search date and time selection ……………………………………..70
11.3 Search screen play ……………………………………………………71
11.4 Search screen zooming in and brightness adjustment…………….72
12. 2Way Audio…………...…………………………………………………..73
DigiNet Center User Manual
Contents
Contents

1. WebDVR Connection……………………………………………….93
2. WebDVR Function Description.. ...........................................95
2. WebDVR Manual
Table of contents
Table of contents
2
1. PSTN/ISDN(in case of not using Router) setting up PPP …- 97
2. Manual setup of ISDN without Router ……………………………99
3. CD formatting and backup using Direct CD S/W ………………101
4. CD formatting using InCD S/W………………………………………105
5. System setting for using 2Way Audio function…………………108
Chapter 3 Appendix
contents
contents
3
13. K-Remote Backup Server ................................................................74
13.1 Change Password...........................…………………………………75
13.2 Backup log...........................………………………………………….75
14. Intelli Upgrader ……………………………………… ………………….77
14.1 Intelli Upgrader ………………………………… …………………….77
14.2 Remoteness upgrade …...……………………… …………………...78
15. Health Monitor ……………………………………………………………80
15.1Performing Health Monitor ……………………………………………80
16. Emergency Monitor………………………………………………………89
16.1 Performing Emergency Monitor ……………………………………...89
1
DigiNet Center User Manual
Contents
Contents

1. DigiNet Center Manual
1. How to connect Communication line….......................................…7
1.1 Connect ISDN, DSU, exclusive line........……………………………7
1.2 MODEM, LAN connection.....…………………………………………8
2. How to install Center program………………..........…………………9
3. Execute Center Program………………….......………………………12
4. Main Screen setup…………………......………………………………13
5. Center Communication setup………………….........………………14
6. How to connect SITE ……………………………….…………………18
6.1 LAN connection........................…………………………………….19
6.2 PSTN,ISDN connection..........................………………………….21
7. How to signal current image…….............………………………….24
8. Switch to search mode……………....……………………………….25
8.1 Search date and select time...................………………………….26
8.2 Camera selection ………………………………………………….27
8.3 How to replay search screen.......………………………………….28
8.4 Book mark……………………………………………………………31
8.5 Search screen zooming in/out and moving ……………………..32
8.6 Search screen quality improvement……………………………….33
8.7 Audio play…………………………………………………………….34
8.8 Backup data........................................…………………………….35
8.9 Print searched screen..............…………………………………….44
9. PAN/TILT & Converting watch mode…….....................................46
9.1 How to control PAN/TILT mode....…………………………………47
10. Setup Remote site……….........................…………………………48
10.1 Setup hardware……………...............……………………………49
10.2 Setup motion detection..........…………………………………….53
10.3 Setup recording schedule.........................………………………56
10.4 Site information..............................………………………………60
10.5 System setup...............……………………………………………61
10.6 Other….........……………………………………………………….66
11. How to search backup data …………………………….………….67
11.1 Search mode conversion ………………………………………..69
11.2 Search date and time selection ………………………………….70
11.3 Search screen play ………………………………………………...71
11.4 Search screen zooming in and brightness adjustment ………72
12. 2Way Audio ……………………………………………...……………73
13. K-Remote Backup Server ………………………………………….74
13.1 Change Password.......................................…………………….75
13.2 Backup log..................................…………………………………75
14. Intelli Upgrader…............…………………………………………….77
14.1 Execute Intelli Upgrader..........……………………………………77
14.2 Remoteness upgrade...……………………………………………78
15. Health Monitor ………………………………………………………..80
15.1performing Health Monitor ………………………………………...80
16. Emergency Monitor…………………………………………………..89
16.1performing Emergency Monitor …………………………………..89

7
1. Connection
ISDN T.ADSU
(exclusive modem)
exclusive line
ISDN T.ADSU
(exclusive modem)
CENTER PC
1.1 LAN, ISDN(using Router), connecting exclusive line.
Router
Router
Internet network
&
Local Intranet network
LAN
(connecting with UTP terminal of LAN card)
Lan
(connecting with UTP terminal of LAN card)

8
MODEM
PSTN
(regular phone line)
CENTER PC
MODEM
1.2 Connecting PSTN, ISDN modem
ISDN TA
(25 PIN)
ISDN line
ISDN T.A.
Connecting with
COM 2 terminal
( 9 PIN )

9
2. Center Program Installation
Insert Center program CD into CD-ROM and click the folder that has center program.
Then double-click on folder <disk1>.
Execute a file called <setup>
1
2

10
Click <Next>
Check on ‘I agree to the License Agreement’ and click <Next>
Select the path where you want to install DigiNet Center program and click <Next>
3
4
5

11
Click <Next>
Installation will start.
DigiNet Center icon will be created in the background as below.
Double-click DigiNet icon and run Center program.
7
8
6

12
3. Center program execute
Execute center program by double-double clicking DigiNet icon on desktop.
Password setup window
DigiNet check the password when it starts.
(It doesn’t have a password as a default.)
![Caution]
• It is impossible to change your password if you forget it.
(Please write it down in another place.)
• We recommend that the administrator changes the password.
Refer to page 17 for password change.
1
2

13
[Now] Button for bringing current image while connected to site.
[Search] Button for changing into mode for finding data and site data.
[Setup] Button for setting up site while connecting to center program or site.
[Connect] Connection button for accessing the site.
[up/down stream] Shows the current stream condition between site and center.
[Quit] DigiNet ] Close button for closing center program.
[Disconnect] Button for disconnection site and communication access.
First screen
Displays current date and time.
Shows the name of setting place and IP address of the connected site.
4. Main screen setup
2
3
4
5
7
8
6
9
1
1
2
3
4
5
6
8
9
7

14
2
5.Center setup
How to setup
How to setup
[Setup]
Configurate system environment
Click this button.
[OK]
Pressing <OK> brings you to the
initial screen.
Center setup will be displayed.
2
1
2
1

15
[Store searched image]
When you search for recorded image after
connecting to the site, this function will
simultaneously store the image to a designated
HDD.
[Select storing drive]
When searching for recorded data and current
image after connecting to site, select HDD that will
be recorded from the Center.
[Reconnection after connection is released]
This function is to establish reconnection when
connection is released during images are being
transmitted.
☞[Tip] Applicable storing media
You can only record in network drive and in
drives which can support the following; Hard disk
or remote drive (DVD-RAM, ZIP, MOD, ORB, USB
HDD etc.).
Setup Configuration
Setup Configuration
1
2
3
5
4
6
1
2
3
5
4
6
7
[Modem connection time]
Center system disconnect the connection
after the selected time if there is no
response.
[Display of manual control status]
Displays manual control button on
the screen.
[Water Mark Setting]
Water Mark Authentication Mark: This function
indicates Watermark authentication mark.
Watermark authentication mark will be
displayed on image when you select this option.
[Store current image]
When transmitting image after connecting to a site,
this function will simultaneously store the image to a
designated HDD.
7

16
[Select line type]
• Select communication line type you wish to use.
Select ‘PSTN/ISDN (NO ROUTER) when using
regular phone line or ISDN (Without Router).
• Select ‘LAN/ISDN(ROUTER)/LEASED CIRCUIT
(ROUTER) when using LAN or ISDN/ISDN only line
(With ROUTER).
[Installed modem name]
•This will automatically recognize and show
modem that is installed in the system.
(It will only automatically recognize the modem
type when (‘PSTN/ISDN(NO ROUTER)’ is selected).
[Initial order]
This will automatically recognize initial order from
window from the modem that is installed in the
system.
[Port and communication speed]
• This will automatically recognize communication
port and its speed that is installed in modem.
1
2
3
4
Communication
Environment
Communication
Environment
☞[reference] PPP settings with using
PSTN/ISDN Modem
Must set additional PPP in case of using
communication with using PSTN/ISDN
Modem. (see Page 97 )
1
2
3
4

17
1
2
3
4
[Change password]
• This is used to change password.
(There is no password in the factory setup.)
• Enter password and click <ok>
• Enter new password and click <ok>
[Clock Display Format]
• This is a format for displaying current date
and time.
[OK]
• Click <Ok>after entering data.
[OK]
• You can go back to initial menu by pressing
<Ok> button.
Etc.
Etc.
1
2
3
4

18
6. How to connect to Site DVR
[Connect]
You can connect to site DVR with this.
Click this on the initial screen.
1
1

19
1Once a user clicks the button, the following connection
setting window is displayed.
2[Add]
Select the button,[Add] and set site codes, IP addresses, installation sites and
passwords and finally choose the button, [OK].
AB
C
E
F
D
G
A
B
[Group] : A user sets a group for entered site information.
[Group Add] : A user creates a new group for entered site information.
[SITE Code] : A user adds site codes in a following order of 100-001,100-002,100-003....
[SITE Name] : A user enters a installation site and a name of a site.
[IP Address] : A user enters an IP addresses of a site.
[Password] : A user enters a password for connection set in site setting menu(communication
settingÆconnection settingÆpassword for connection).
[Confirm] : A user enters a password for connection to a site.
C
D
E
F
G
[Connection list] : In order to connect to a site, a user should enter groups, site codes, IP
addresses, installation sites and passwords and put them on the connection list after selecting
[Add]. When a user intends to connect to related sites again later, he has only to choose the
connection list and this procedure facilitates his connecting to related site.
A
A
![Caution]
During the connection from CENTER to a site, a site code and a password are
compared and searched simultaneously. In case either the site code or the password
is wrong, the connection fails.
6.1 LAN environment connection

20
3[Edit]
A user chooses sites of which information is to be
edited and then selects the button, [Edit].
On editing information of the site, a user saves
the edited site information just by selecting
the button, [OK].
5[Delete]
When a user wants to delete entered site information,
he chooses the related information and then selects
the button, [Delete].
4[Connect]
On choosing the site to be connected, a user selects
the button, [Connect].
The window displays a progress status of
connection to the site.
6[Cancel]
Selecting [Cancel] terminates the connection
information window and retrieves the main window.