Kogan KAPWDBIDETA User manual

SMART WASH & DRY ELECTRIC
BIDET TOILET SEAT
KAPWDBIDETA

Read all instructions before use and retain this user guide for future reference.
Read all following safety precautions carefully before use.
All images within this user guide are for reference only, refer to the actual product.
Symbols on the product and in this user guide:
WARNING!
Warning: Failure to follow instructions with this symbol may result
in serious injury or death.
Caution
Caution: Failure to follow instructions with this symbol may result
in injury and property loss / damage.
Forbidden: Statements with this symbol are forbidding an action
as described.
Alert: Statements with this symbol are alerting the user to an
enforced, compulsory action.
WARNING:
• Do not touch the electrical outlet with wet hands, or it may cause electric shock.
• Do not pour water, hot water or detergent on the top of the toilet or electrical outlet, as it
may cause fire, electric shock, heat or short circuit. It may also cause injury and indoor
water seepage due to damage of product.
• Never attempt to disassemble, repair or alter the product yourself, as it may cause fire,
electric shock, heat or short circuit.
• Do not install the toilet in car, ship or any other moving object, as it may cause fire, electric
shock, short circuit or fault. The ceramic, seat and main part may be damaged from
falling down due to motion.
• If the product is not working, stop using immediately.
• Under the following conditions, immediately disconnect the power supply and turn
off the water angle valve:
- Water leakage from pipe or inside of the product
- Crack or damage on the product
- Unusual sound or smell
- Smoke
- Unusual heating
SAFETY & WARNINGS

- Block
- Fall out of the cushion
• The continued used of the product, by ignoring the above faults, may result in fire,
electric shock, heat, short circuit, injury and indoor water seepage.
• Do not use any type of water except tap water or drinkable well water (underground
water). Do not use seawater. Use of other waters may cause skin inflammation or fault.
• Do not touch the electrical plug during thunder, as it may cause electric shock.
• Do not let the water inlet soft pipe connect to the electrical plug and outlet, as it may
cause fire, electric shock, heat, short circuit because of moisture condensation.
• Do not destroy or damage the power cable or plug.
• Do not damage, strike, yank, twist, excessively bend, bind, pinch or in any way alter the
electrical cords. Do not place anything heavy on the cords. Failure to follow this instruction
may cause fire, electric shock, heat and short circuiting.
• Do not use a loose or faulty electrical outlet or it may cause fire or short circuit.
• Do not use any power supply other than AC 220V, 50Hz.
• Do not place fingers or anything else into the warm air outlet, and do not place objects or
clothes on the air outlet or cover it. Failure to follow this may cause scalding, electric shock
or fire damage to accessories.
• Keep open flames (matches, cigarettes, etc) away from the product at all times, as it may
cause fire.
• The toilet seat will only function when the seating sensor on the seat ring detects that
there is a person seated (you will hear a beep sound when seated).
Caution:
• Pay attention to low temperature scalding.
• Improper use of the seat warmer may cause low temp scalding. If sitting for a long
time, turn the temp setting to “off”.
• Turn the seat temp setting to “off’, and warm air-dry temp to “low”, under following
conditions:
- Being used by children, older people, or people who cannot adjust the
temperature settings.
- People with disabilities who may be unable to adjust the temperature settings
- People who have taken medicine causing drowsiness (cold medication,
sleeping pills, etc), under the effects of alcohol, or are otherwise inebriated.
• As this an electrical product, do not install it in a location where it can easily get wet or a
location with high humidity. If installed in bathroom, please also install ventilator to
maintain the bathroom ventilation. Failure to do so may cause fire or electric shock.
• Do not install close to a bathtub.
• Ensure the product is connected to cold water supply, or it may cause body burn or
machine fault.
• The product must be connected to the ground correctly. If not connected to the ground, it
may cause electric shock. Only use with supplied 3-prong (grounded) electrical plug.
• Use only an electrical outlet with leakage switch (rated induced currents below 15mA) or
insulating transformer (1.5kVA~3kVA) to protect outlet loop. Failure to do so may cause fire
or electric shock.

• Ensure the plug is firmly inserted into the wall outlet at all times, or it may cause fire, heat
or short circuit.
• When removing the plug from wall outlet, remove by holding the plug. Do not pull on the
cord.
• If the power soft wire is broken, cease use immediately and contact Kogan.com for
replacement or repair.
• Turn off the power before doing any general maintenance or spot checks. Nozzle clean will
require power to check.
• People in need of supervision or a guardian (people with disability, children, older people)
must not be left unattended with the device.
• Do not let children play this product.
• Do not throw lit cigarettes, matches, or any other flaming material into the toilet.
General safety notices:
• Do not use the product when it is loosely fitted. The toilet and seat may separate and fall
off, causing body injury.
• If damaged, do not touch broken area. Cease use and contact kogan.com for assistance.
• Do not impact forcefully, put heavy weight upon, crouch on, or stand on the product. This
may cause product damage, personal injury, or indoor water seepage.
• Do not use the seat for anything other than what it was designed for. Do not pull the
product by holding the seat or cover, and do not attempt to sit on it while it is not in
position. Failure to do so result in product damage or injury.
• Use kitchen detergent (neutral) to clean the plastic parts (seat cover, etc) and water inlet
soft hose. Do not use the following materials: bathroom detergent, house detergent,
petrol, banana oil, cleaning powder, nylon brushes, etc. These products may damage the
plastic parts, cause cracks, or may cause water leakage because of damaged soft hose.
• To a v o i d s u d d e n w a t e r l e a k a g e , d o n o t r e m o ve t h e w a t e r i n l e t f i l t e r w h e n a n g l e v a l v e i s
open. Refer to Cleaning and Care section of this user guide.
• Do not crush or bend water inlet hose, as it may cause water leakage.
• If replacing another bidet, use the new hose supplied with this product. Do not reuse the
previous hose, as it may cause water leakage.
• Do not pour hot water into toilet, as it may cause body injury or indoor water seepage due
to toilet damage.
• Do not flush with large amount of toilet paper or other subjects except sewage and small
amount toilet paper, as it may cause toilet damage. Do not flush tampons, condoms, or
sanitary products.
• Do not lean on the toilet cover while using, it may damage the seat cover.
• Close the angle valve when water leaking
• When room temperature is below 0°C, to avoid piping or soft hose damage, anti-freezing
measures should be adopted. If water Inlet soft hose is frozen it may destroy main body or
piping, leading to water leakage. To avoid damage, please pay attention to room
temperature adjustment.
• When not use for a long time, drain the inlet soft hose and disconnect from power. When
next using, open the angle valve and let water connect first, or it may cause skin

inflammation due to poor water quality. It may cause fire or overheating if the power
supply is always connected.
• Confirm that the filter is screwed to correct position installed, prior to using. It may cause
water leakage if not screwed tight.
• When the toilet drain outlet is blocked, cut off the power then clean the obstruction.
Otherwise sewage may overflow, causing indoor water seepage because of auto flush
function.
• Flush the toilet after each use. Failure to do so may result in difficulty cleaning the toilet,
blocked drain outlet or sewage overflow, resulting in indoor water seepage.
• After each use, if there is any mess on floor, always clean immediately to prevent corrosion
or unhygienic build-up.
• Extended heating without sufficient water supply will lead to the heater becoming burned.
• Directly exposing the remote control to water may cause the remote to cease functioning.

DIMENSIONS

Ensure you have all of the components listed in this user guide before disposing of any
packaging.
To i l e t S e a t
User guide
Front wash nozzle
Rear wash nozzle
PE Intel Pipe
Rubber gasket
Spanner
T Valve with filter
Mounting bolts (x2)
Rubber sleeves
(x2)
Metal gasket (x2)
Fix bracket
Remote control
Remote bracket
AAA alkaline
battery (x2)
Double sided tape
COMPONENTS

Note: Ensure the screen protector is removed prior to first use.
OVERVIEW
To i l e t l i d
Water inlet
Control panel
Seat
Seat sensor switch
Cushion pad
Damper
Dryer outlet
Deodorizing box (inside)
Nozzle for rear wash
Nozzle for front wash
LED Display

Precautions before Installation
• Before installation ensure toilet wall, floor tiles, ceramic toilet have all been
installed. Your bathroom should have water supply and power socket nearby toilet.
• Water pressure should be between 0.06Mpa (flow) - 0.75MPa (Static), water
temperature 5°C - 35°C.
• In case of transportation in subzero (freezing) condition, place the product in a
warm place and wait for any residual water to thaw before installing.
• Connect daily-use water pipe only. Use tap water or drinkable well water only. Do
not connect to recycled water or industrial water supplies, due to possible
contamination as this would cause jamming or internal damage.
• Be sure to use T valve and filter.
• Ensure the water supply is fully connected before connecting the bidet to the power
outlet.
1. Install T valve with filter
• Lock inlet valve to remove water pipe (Figure 1).
• Connect T valve with filter and inlet valve (Figure 2).
• Install flush tank and inlet pipe (Figure 3).
INSTALLATION
Water
pipes
Valve
OFF
Figure 1
T valve
filter
Gasket
Valve
Flush tank
Valve
Figure 2
Figure 3

2. To i l e t S e a t I n s t a l l a t i o n
Remove original toilet seat
• Loosen bolts with wrench
• Remove the nut and gasket,
remove the toilet seat
Install fix bracket
• Before the installation, place the product on the toilet bowl to check for correct
fitting.
• Embed and install the rubber sleeve, fix bracket, metal bracket as shown below.
• Insert the mounting bolt and tighten it so that the fix bracket cannot move.
• If the product does not match the toilet bowl ideally, loosen the mounting bolts,
remove the metal gasket, readjust the position of the fix bracket, then replace the
metal gasket and tighten the bolts.
The fix bracket can adjust the range between 130-170mm.
To i l e t
seat
Bolt
Gasket
Nuts
Release
Mounting bolts
Metal bracket
Fix bracket
Rubber sleeves

3. Install bidet
• Aim the bottom card slot of the seat to the
edge of fixed bracket, slide in gently. You will
hear a “click” sound when it is correctly
placed.
• Ensure the bidet fits into the area before
placing, then lift bidet to fit it in correct
position.
• Ensure the installation is correct before use.
Long term uneven force will lead to cracking
of the seat ring.
4. Connect Inlet Pipe
• Connect T valve: Hold PE inlet and push it towards the connector of T valve.
• Connect bidet: Hold PE inlet and push it towards the connector of bidet.
• Tu r n o n t h e i n l e t v a l v e a f t e r c o n n e c t i n g t o c h e c k t h e c o n n e c t o r s f o r s i g n s o f
leakage.
T valve
In valve
PE inlet
Fix
bracket
Bidet
Note:
Do not forget to allow space for the power cable
between the toilet and bidet.

5. Installing the Remote Bracket
• Ensure the installation area is thoroughly cleaned and dry before proceeding.
Apply the supplied double sided tape to the rear of the remote bracket.
• Adhere the remote control bracket to the wall pressing firmly. Allow the remote
bracket to bond for 15 minutes before placing the remote control in it.
Double sided tape
Remote bracket
Wall
Remote bracket

Preparation for Water Supply and Test for Operation
1. Insert the power plug into the electrical socket.
2. When the indicator light is on, water starts to flow into the inner water tank. The
process will take approximately 11 seconds. Water then sprays out from the nozzle.
All indicator lights will then turn off with a sound.
3. Press the power button on the toilet or on remote control, then the power indicator
light or power icon on the LED display will turn on.
4. Adjust the temperature of water and toilet seat to an appropriate level.
5. Follow the instructions to operate, press buttons as instructed and test every
operation.
6. The toilet seat will only function when the seating sensor on the seat ring detects
that there is a person seated (you will hear a beep sound when seated).
Preparation
1. Ensure the plug is inserted into the power socket
then press the reset button on the residual current
device (RCD). The indicator turns from black to slightly
red.
2. Open the water inlet valve
OPERATION

3. Confirm the power icon in LED display is on.
Power
4. If the power light on the product indicator panel is not
lit, all functions will be unavailable. Press the power
button on the control panel to activate.
Controls & Display
This product is controlled mainly using the remote control, with the control panel as a
secondary measure.
Remote control
Indicator panel
LED Display
Control Panel

Remote Control
This product is controlled mainly using the remote control, with the control panel as a
secondary measure.
Rear wash/
Oscillating
Front wash/
Oscillating
Dryer
Front/Nozzle
Back/ Power
saving
Indicators
Water temp
Child Wash
Strong / Deodoriser
Weak / Night light
Seat temp
Lady care
Strong wash
One solution
Stop

Rear wash/Oscillating:
Press this button and the rear wash nozzle will extend for operation. Press again to change
to rear oscillating cleansing. The #1 indicator will blink on the remote control, while the nozzle
repeatedly swings back and forth. Press again to stop oscillating cleansing and switch back
to rear wash.
Front wash/Oscillating:
Press this button and front wash nozzle will extend for operation. Press again to change to
front oscillating cleansing. The indicator #1 will blink on the remote control, while the nozzle
repeatedly swings back and forth. Press again to stop oscillating cleansing and switch back
to front wash.
Stop:
Stop the current operation. Press and hold this button for 3 seconds to shut down toilet seat.
Nozzle position adjustment:
Press the “Front” and “Rear” buttons to adjust the position of the nozzle. The nozzle position
cannot be adjustment while oscillating.
Water pressure adjustment:
During wash operation press the “Strong” or “Weak” buttons to adjust the water pressure.
Dryer:
Press this button to start the warm air-drying operation. This operation automatic ends after
4 minutes or when the user presses the “Stop” button.
Warm air temperature adjustment:
Whilst drying, press the “Strong” or “Weak” buttons to adjust warm air temperature to suit
your needs.
Nozzle self-cleaning:
Press the “Nozzle” button on remote control while in standby mode. The water will start to
flow to clean the nozzle. Press this button repeatedly and the nozzle switches between rear
and front cleansing and then you can clean and replace the nozzle.
Note:
Standby mode means that the toilet seat is in an operational state. The toilet seat is
not in the state of washing, drying, nozzle self-cleaning, etc.

Water temperature adjustment:
The water temperature can be adjusted between 4 different levels. Press the “Water temp”
button to cycle through the preset temperatures. The number indicators will display the
current setting as shown below:
Room temperature
(No indicator)
39°C
(#1)
36°C
(#2)
33°C
(#3)
Night light:
Press the “Night light” button whilst in standby; the #4 indicator will blink and the light will
turn on. Pressing the button again will turn off the light.
Seat temperature adjustment:
The seat temperature can be adjusted between 4 different levels. Press the “Seat temp”
button to cycle through the preset temperatures. The number indicators will display the
current setting as shown below:
Room temperature
(No indicator)
39°C
(#4)
36°C
(#5)
33°C
(#6)
Note: To p r ev e n t t h e l o w t e m p b u r n , t h e temperature will automatically reduce to below
35°C after sitting on the seat for 10 minutes.
Power saving:
Press the “Power saving” button whilst in standby; the #3 indicator will blink and toilet seat
will go into power saving mode. Pressing the button again will cancel the operation.
Deodoriser:
The deodoriser feature is on by default. During drying, the deodorising function is
temporarily stopped, and it will automatically resume after the drying is completed. When a
person leaves the seat, the deodorising function will continue to work automatically after 90
seconds.
To d i s a b l e t h e feature, press the “Deodoriser” button whilst in standby; the indicator #2 will
blink. The deoderiser is now switch off. Press the button again to turn the feature back on.
Lady care:
Cleansing suitable for menstruation. Whilst in standby, press the “Lady care” button to
begin operation. The nozzle extends out to and water temp is set to the highest level (39°C).
Water temperature and pressure is not adjustable however the nozzle position can be
adjusted to suit your needs. This operation automatic ends after 2 minutes or when the user
presses the “Stop” button.

Child wash:
A warm water gentle cleansing suitable for children. Whilst in standby press the “Child
wash” button. The front wash nozzle extends out with nozzle position at the front. The water
pressure is low and the temperature is set at 36°C. This operation automatic ends after 30
seconds or when the user presses the “Stop” button.
One solution:
Pressing “One solution” button will start the following operations in the order shown below:
• Rear wash for 40 seconds
• Oscillate wash for 20 seconds
• Warm air dryer for 2 minutes
The user can end the operation at any time by pressing the “Stop” button.
Strong wash:
Whilst in standby, press “Strong wash” button. The rear wash nozzle extends oand the water
pressure will be set to the highest mode. This operation automatic ends after 2 minutes or
when the user presses the “Stop” button.
Indicator Panel
• Power: When the power is on, the indicator turns on. If there is something wrong
with flushing components, the indicator light will blink.
• Water: When the water is heating, the indicator light is on. If it is over heated, the
indicator light will blink.
• Seat: When the toilet seat is heating, the indicator light is on. If it is over heated,
the indicator light will blink.
• Sitting: When the toilet seat detects a person, the indicator light is on.
• Save Power: When it enters energy saving mode, the indicator light is on.

LED Display
• 1. Night light: illuminates when the night light is on.
• 2. Power saving: illuminates when the power saving mode is on.
• 3. Power: illuminates when the power is on.
• 4. Deodoriser: illuminates when the deodoriser is enabled and user sits on the seat.
• 5. Water temp: When the water is heated, the temperature will be displayed in
numerals. If an error occurs, the temperature figure will display letters:
- D: heater problem.
- E: water temperature sensor problem.
- F: current water temperature is high.
• Save Power: When it enters energy saving mode, the indicator light is on.
1
2
3
4
5
6