TRONE Nobelet NETBCDER-12.WH User manual

Nobelet Installation Manual
bidets reimagined

INSTALLATION PREPARATION
Before installation begins, please confirm that you have the materials
indicated below:
Included
Electronic Bidet Remote Control
Nobelet Installation Manual
bidets reimagined
Installation Manual
Wax Ring Valve Stop Battery Back Up
Batteries
3/8” x 1/2” Supply Line
1/4” Pex Adapter
Washers Filter
x2

2
Recommended Tools
Precautions Before Installation
Please give enough allowance for the installation. Ensure that there is
room enough for the opening and closing of the bathroom door. Please
see diagram below for product placement measurements.
Please confirm the location of the sewage outlet and the wax ring as
indicated below before installation.
Pencil Masking or
painters tape
Tape measure
or ruler
7/16” ratchet box
wrench or deep socket
ratchet wrench
Carpenter’s
square or other
straight edge
11” +
18-1/2”
15”
Sewage Outlet
Water & Power
Not Allowed
In This Space

3
Installation Requirements
Minimum static water pressure: 40 psi
Maximum static water pressure: 80psi
Minimum water flow: More than 1.4 gallons per flush (5.28 liters)
115 V power GFCI receptacle within 4’
Installation Drawings
15” +
Wax Ring Finished Floor
Sewage Outlet

4
INSTALLING THE WATER VALVE
Note: The valve supplied with Trone toilets is not a tapered thread and
will need one of the two options listed below.
Option #1: Retro fit with water supply line (easiest method)
1. Turn off toilet supply stop.
2. Remove existing 3/8” x 7/8” toilet supply tube.
3. Attach the provided 3/8” x 1/2” braided faucet water supply
line.
Note: If your existing water supply valve is not 3/8” compression
you will have to source a supply line that can fit on it and adapt to
1/2” NPT.
4. Attach the provided valve stop to the faucet water supply line.
Option #2: Replumb water line supply to pex (new construction,
remodels, and plumber installation. Not recommended without a
professional)
1. Turn water off to the house.
2. Remove current toilet water supply valve.
3. Adapt plumbing to ½” pex either in the wall or outside.
4. Crimp pex swivel female adapter (provided) onto pex.
5. Attach the provided new valve.
Note: For new install rough-in, 5” from finished floor and 10” left of
center for ease and accessibility. It is not recommended to be
placed behind the toilet.

5
INSTALLING THE TOILET
1. Place the wax ring over the closet flange making sure it is
centered, with the flange down. Install the closet bolts.
2. Remove the electronic bidet seat by pulling upwards firmly on
the back of the seat until it releases (see Figure 1 below).
3. Gently set the bidet seat across the toilet bowl and out of the
way as much as possible.
4. Lift the entire electronic toilet bidet unit and place it over the
wax ring. (It is recommended to use two people to lift and set
this toilet).

6
5. Line up the holes in the bottom of the bowl with the closet bolts
previously installed in the closet flange and set the bowl gently
in place (see Figure 2 below).
6. Place the included closet washers over the closet bolts and hand
tighten the nuts in place.
7. Secure the bowl in place by tightening the nuts down,
alternating from side to side using a ratchet wrench or similar.
Note: Do not over tighten as you may crack the porcelain/base. If
there is still movement once tightening is done, shims may need to
be used to account for an unleveled floor.

8. Double check all water lines are properly connected.
9. Double check the battery backup is hooked together. It is
recommended to replace the battery backup with a new
battery.
10. Replace the bidet seat by lining it up and pushing down gently
on the top part of the seat.
11. Plug in the cord and reset the GFCI by pushing the larger of the
two buttons on the plug.
Note: If there is power to the Electronic bidet, it will automatically
run through a cleaning cycle to insure all functions are working
properly.
7

8
Connecting the Water Supply
1.$WWDFKWKHȴOWHUWRWKHZDWHUVXSSO\YDOYH
DQGWKHQWLJKWHQLWZLWKDZUHQFK
2.$WWDFKWKHȵH[LEOHWRLOHWȵXVKVXSSO\WRWKH
ODUJHVWFRQQHFWLRQRQWKHȴOWHUDQGWLJKWHQLW
ZLWKDZUHQFK
3.$WWDFKWKHVPDOOHUȵH[LEOHELGHWOLQHWRWKH
ȴOWHUDQGWLJKWHQLWZLWKDZUHQFK
4.ΖQVWDOODWLRQLVGRQH
)LOWHU
)LOWHU
:DWHUVXSSO\
DQJOHYDOYH
)LOWHU
1XW
:DWHUVXSSO\KRVHV
:DWHUVXSSO\KRVHV
)LOWHU
:DWHUVXSSO\
DQJOHYDOYH

9
Caulk Application
Caulk the bottom edge of the toilet with a mildew-resistant caulk
designed for indoor bathroom applications. This will help to keep the
bowl in place and give the closet bolts added security and strength.
Connecting the Power Cord
Open the angle valve and connect the power cord plug to the power
outlet. The power cord plug must be connected to a wall socket with a
safety grounding device in AC 120V, 16A, 60Hz.
Caulk
Caulk

10
Battery Installation
1. Take the cable out as illustrated below. It is attached to the back of
the product; peel it off gently.
2. Connect the waterproof DC power plug and tighten the waterproof
cap.
3. Place the battery case in its position as shown below.
Remote Installation
1. Peel the protective tape of the foam tape at the back of the
bracket and stick it to the selected dry tile or glass.
2. Open the back cover of the remote and place three pieces of new
No. 7 alkaline batteries.
3. Place the remote on the remote bracket.
4. Installation is complete.

[e-mail]
www.troneplumbing.com