Kogan KAWWASHT85A User manual

8.5KG TOP LOAD
WASHING MACHINE
KAWWASHT85A & KAWWASHT85B

2
Safety & warnings 3
Overview 6
Installation 7
Operation 12
Cleaning & care 23
Specifications 26
Troubleshooting 27
Notes 29

3
Read carefully and keep for future reference.
Read this user guide thoroughly before first use, even if you are familiar with this type of
product. The safety precautions enclosed reduce the risk of fire, electric shock and injury
when correctly adhered to.
Keep the user guide in a safe place for future reference, along with the completed warranty
card and purchase receipt. If applicable, pass these instructions on to the next owner of the
appliance.
Always follow basic safety precautions and accident prevention measures when using
an electrical appliance, including the following:
Warning This heading indicates that there is a serious risk of injury if you do not
adhere to the warning(s).
Caution This heading indicates that care should be taken to avoid injury to
persons or damage to property.
Electrical safety
•The appliance is rated 230-240V - 50Hz. Ensure the voltage supply at your home
corresponds to this.
•Only connect the washing machine to a grounded (earthed) electrical outlet.
•Do not insert any objects into the appliance.
•Do not kink or damage the power cord and position it out of the way so no one steps on
or places anything on the cord or against it.
•Do not overload the wall outlet. Overloading can result in fire or electric shock.
•If the power cord is damaged, contact Kogan.com for support.
•Never use this washing machine with a power adaptor or an extension cord.
•Unplug the washing machine from the power supply before cleaning, servicing,
performing maintenance or moving the appliance. Pull by the plug, not by the cord.
•After use, always unplug the appliance and turn off the water.
•Warning: All electrical work must be done in accordance with local and national
electrical codes as applicable and should be undertaken by licenced and qualified
persons only.
SAFETY & WARNINGS

4
Installation
•Install the washing machine on a flat surface to avoid overturning during use. If the
machine must be placed on carpet, make sure any ventilation openings in the base are
not obstructed.
•Install the washing machine so that there is a distance of at least 200mm between the
appliance enclosure and any external heat sources, such as appliances containing
heating elements.
•Connect the washing machine to the water mains using new hose sets. Do not reuse
old hose sets. The required water pressure is 0.03MPa (min.) to 0.8MPa (max.).
•Ensure that all water and electrical connections are made by qualified personnel only,
observing local safety regulations and following the manufacturer's instructions.
•Improper installation may result in the risk of fire, electric shock and/or injury. No liability
for any eventual damages caused by improper installation.
Usage conditions and restrictions
•The appliance is designed for private domestic use only. It is not suitable for
commercial or trade use. The appliance has a capacity (max. weight of dry wash load)
of 8.5kg.
•Do not operate the appliance outdoors.
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
•Children should be supervised to ensure they do not play with the appliance.
•Before loading the machine, always ensure no pet or young child has climbed into it.
•Make sure all pockets of clothing to be washed are empty. Hard, sharp objects such as
coins, safety pins, bra wires, nails, screws or stones can cause extensive damage to the
appliance and block the pump.
•Any damage or malfunction resulting from foreign objects is not covered by your
warranty and may lead to expensive repairs. No liability for any eventual damages
caused by improper or faulty use.
Cleaning and maintenance
•Before cleaning or performing maintenance, always unplug the appliance from the
power supply.
•Except for the filters that require regular cleaning, the unit has no user-serviceable parts
contained within. Do not attempt to repair, disassemble or modify it. Repairs made by
inexperienced or unqualified persons may cause injury and/or make more serious
repairs to the appliance necessary.

5
•CAUTION: After each wash, check and clean the lint filter inside the drum. Also check
and clean the lint filter at the rear of the machine next to the drain hose outlet on a
regular basis.
•This appliance should only be serviced by an authorised service centre and only
genuine spare parts should be used. Contact help.kogan.com for support.
Warnings
•Do not let children climb into the washing machine or peer into the rotating spin barrel.
•Do not wash clothes that have residue of flammable materials.
•Do not use the appliance if the power cord or plug is damaged to avoid an electric
shock, short circuit or fire.
•Regularly clean the power plug to remove dust and dirt and avoid contact failure.
•Turn the machine off before pulling out the plug from the socket if the machine is not in
use.
•Do not place any lit candles or cigarettes on top of the washing machine.
•Insert the power plug securely.
•Use a 230-240V AC power source.
•To avoid electric shock, fire and malfunction, do not install this machine in a damp
place.
•Do not pull out or insert the plug with wet hands to avoid electric shock.
•Ensure the water inlet hoses are connected and the taps are turned on before washing
a load.
•Do not allow children to lay or sit on top of the washing machine.
•Do not change the power cord. If it needs changing, contact a qualified electrician or
call the after-sales support line.
•Do not wash jackets, raincoats, fishing coats and similar clothes in the washing
machine.
•Do not pull the power cord when removing the plug.
•The water temperature does not exceed 60°C when washing with warm water.

6
No
Description No Description
1 Lid 6 Wash/spin tub
2
Control panel 7 Water supply hose connections
3
Housing 8 Drain pump filter
4 Detergent box 9 Drain hose connection
5
Lint filter 10 Adjustable leg (1)
Accessories
No
Description No Description
11 Hot water supply hose 12 Cold water supply hose
13 Drain hose with elbow
OVERVIEW
Front Rear
Top
Accessories

7
Unpacking
•This product has been packaged to protect it against transportation damage. Keep the
original packaging carton in a safe place. It will help prevent any damage if the product
needs to be transported in the future. If it is to be disposed of, please recycle it and all
other packaging materials where possible.
•Plastic wrapping can be a suffocation hazard for babies and young children, so ensure
all packaging materials are out of their reach and disposed of safely.
•Unwind the power cord to its full length and inspect it for damage. Do not use the
appliance if the appliance or its cord has been damaged or is not working properly. In
case of damage, contact Kogan.com support for advice on examination, repair or
return of the damaged product.
•Read this manual to familiarise yourself with all the parts and operating principles of
the washing machine. Pay attention to the safety instructions on the previous pages.
Installing the base cover
•Ensure the power cord is unplugged from the mains
supply.
•Place some padding (such as a soft mat, blanket or
thick towel) on the floor and gently lay the washing
machine on the padding, back side down. Take care
not to dent the housing.
•Insert the base cover into the hooks of the leg, pushing
it straight until it reaches into the back hooks.
•Fasten the base cover with the supplied screw(s).
•Carefully set the washer upright.
Levelling the washer
•Install the washer on a stable and level surface, in a dry location, out of sunlight.
•If levelling is necessary, adjust the adjustable leg (at the front right side of the machine),
as illustrated, below. The maximum permissible inclination of the supporting surface is
2 degrees.
INSTALLATION
CAUTION: Installing the washer on a carpeted floor may cause
vibration issues. If you must install it on carpet, make sure not to block
any ventilation openings on the bottom of the washer.
Screws
Front
Leg
Back
Base
Cover

8
Connecting the water inlet hoses
Install the water inlet hoses to your hot and cold-water taps, as described below.
•Check and ensure that the sealing washers are firmly in place.
•Attach the straight end of the hose to your water taps. Make sure to attach the hot
water supply hose (with RED markings) to the hot water tap and the cold-water supply
hose (with BLUE markings) to the cold-water tap.
•Tighten the coupling nuts securely by hand, as illustrated below (the sealing washer is
part of and located inside the tap end).
•Attach the curved end of the hose to the corresponding inlet valve of the washer.
•Tighten the coupling nuts securely by hand, as illustrated below.
Tighten
Down
Adjustable leg
Up
Loosen
Lock nut
Base of the washer
Top
Sealing washer
Tap end
Inlet hose
Twist

9
•Tighten the nut by turning it clockwise while holding the hose. (To detach the water
supply hose, turn the nut anticlockwise after turning the tap off.)
•Turn on the taps and check for leaks. Tighten the coupling nuts firmly if there is any
leakage. If your water pressure is strong, close the water tap completely, then open it
slightly.
Important:
•Both the hot water and cold-water hoses must be connected to your taps.
•Make sure your hot water from the tap is no hotter than 60°C.
CAUTION:
•When tightening the clamping nut, take care not to damage the water inlet valve joint.
Apply force evenly and do not twist the water inlet valve.
•Use only the new (supplied) hoses with your new appliance. Do not use a hose from an
existing machine or one that has been used previously.
•If the hoses are too short for your set-up, please seek advice from your local washing
machine store to purchase a longer hose.
Nut
Water inlet valve
Nut

10
Installing the drain hose
•The drain hose and drain pump filter are located at the rear of the machine.
•Pinching the two bands of the clamp on the drain hose, connect it to the drain hose
connection at the back of the washer.
•Insert the hose clips for the water drainage hose, into the mounting holes at the rear of
the washer. Turn the clips so you can lead the hose through the clips up the back of the
machine.
•When the washer is in use, put the drain hose into a drain spout (or into a sink/tub), as
illustrated below.
Drain pump
with lint filter Drain hose
connection

11
CAUTION:
•While the washer is in use, ensure the height of the drain hose is at least 70cm,
otherwise the washer will not work properly or the water may flow out while washing.
Ensure the drain hose is not higher than 1m above ground, otherwise the washer will not
drain water well.
•Never lay down the drain hose, as water will be discharged.
•Be sure the drain hose is properly routed so it will not kink or lift off the sink.
WARNING: This appliance must be earthed.
•In the event of a malfunction or breakdown, earthing will reduce the risk of an electric
shock by providing a path of least resistance for the electric current.
•This appliance is equipped with a cord having an equipment-earthing conductor and
an earthing plug. The plug must be plugged into an appropriate outlet that is installed
and earthed in accordance with all local standards and requirements.
•Do not modify the plug under any circumstances. If the plug does not fit your outlet,
consult a licensed electrician and have the outlet changed.

12
Control Panel
Display:
1. The display shows the currently selected option. For example:
Status Display Result
During washing, it shows the time
remaining
Remaining time is 20 minutes
When setting soak and wash
processes, this indicator shows the
time you set
Washing time is 10 minutes
When setting the pre-set timer, it
shows when the washing will be
finished
Finish washing 2 hours later
When an abnormal condition occurs,
it shows the warning code
Water does not flow
OPERATION

13
2. Power ON/OFF button
•Press this button to switch the power on, press it again to switch it off.
•To change the program, press this button once and then once more.
•Power will be switched off automatically:
•5 seconds after the end of a program
•After 10 minutes or inactivity, after the Power ON/OFF button has been pressed
3. Start/Pause button
•Press this button to start operation.
•During operation, press this button to stop the washer temporarily, press it again to
restart it.
•You can also use this button to cancel the end buzzer, press and hold it for 4 seconds
until a beep has acknowledged the command.
4. Detergent indicators
•These scoop indicators show how much powder detergent to use.
•See "Detergent and load recommendations" for details.
5. Program button
•Press this button to select the desired wash program.
•The appropriate indicator light above will flash.
•To set the child lock, press and hold this button for 4 seconds.
6. Process button
Press this button to cycle through the desired wash process: preset (delay timer), soak, wash
time, rinse time or spin time. The appropriate light above will flash.
7. Set button
•Press this button to confirm the desired operation.
•For example, to select rinse time, press Process until rinse indicator flashed, then press
Set to select the rinse time.
8. Temp button
Press this button to select the water temperature.
9. Water Level button
•Press this button to select the water level appropriate for your load size.
•Different water levels for washing and rinsing are optional.
Note: For the Custom, Heavy Duty and Quick programs, the machine will
automatically select the appropriate water level, and wash, rinse and spin times.

14
Before you start washing
•Ensure the washer is stable and level. If necessary, adjust the adjustable leg (front right)
to stabilise the washer. For more information, refer to the “Levelling the Washer” steps
in the Installation section of this user guide.
•Ensure the water inlet hoses are properly installed.
•Plug the machine into a nearby power point.
•Open the water taps.
•Ensure the drain hose is properly installed. Hang the upper end of the hose over the
laundry sink or into a drain spout.
•Before using the washing machine for the first time, run a complete cycle without
laundry items. Select the Custom program and run the machine until the end of the
program.
Normal usage
1. Before washing, remove any coins, keys and other hard items from pockets. Close
any zippers to prevent damaging your clothes and the wash tub. Brush dirt and
sand off clothes and turn pockets inside out.
2. Sort your washing into appropriate loads: whites, coloureds, cottons, delicates,
heavily soiled, etc. Place delicate items into a wash bag for protection.
3. Load your washing items uniformly in the tub.
4. Add washing detergent (see opposite for details).
5. Press the Power ON/OFF button.
6. Refer to the program selection guide and select a suitable wash program.
7. Close the lid and press the Start/Pause button. (If the washer lid is not closed
properly, the washer will sound an alarm and stop working before spinning.
8. At the end of the wash, remove your washing, unplug the power plug from the wall
outlet and close the water taps. Leave the lid open until the interior has dried.
Sensor: The machine will automatically choose the appropriate water level and wash, spin
and rinse times for the Custom, Heavy Duty and Quick programs.

15
Program Suitable items
Default settings for wash processes
Wash
time*
(minutes)
Rinse type Spin time
(minutes)
Normal
Normally soiled cotton
clothing/items; for energy
efficiency test
65 3x Shower rinse 34
Custom Normally soiled cotton
clothing/items
10
(0-20)
2x Water saver rinse
(0-4***)
5
(0-9)
Heavy Duty Heavily soiled cotton
clothing/items
12
(0-20)
2x Water saver rinse
(0-4***)
8
(0-9)
Quick Less dirty clothes
(daily wash)
5
(0-15)
1x Water saver rinse
(0-3***)
3
(0-5)
Blanket Blanket or bulky items 15
(0-20)
3x Water saver rinse
(0-4***)
8
(0-9)
Delicate For delicate clothes 6
(0-15)
2x Water saver rinse
(0-4***)
2
(0-5)
*Total program times differ and depend on the weight of the wash load.
** The Normal program has a fixed (default) setting of level 8 of warm water; all other programs have
cold water as a default (water temperature is adjustable).
*** Times and quantities depend on the wash load and water level.
Detergent and load recommendations
•It is recommended to use detergent in the following amounts recommended below.
Too little will give poor washing results, but too much will affect rinse performance and
may cause overflow of suds, which could interfere with machine operation.
CAUTION: Do not overfill detergent.
•Add detergent into the detergent box or put it directly into the tub.
•If you are using liquid detergent or bleach, dilute it appropriately and pour it carefully
into the hole on the top plate.
CAUTION: Do not pour bleach directly onto the washing load in the tub.

16
Water level
indicator 1 2 3 4 5 6 7 8
Water volume
(approx.) 16L 24L 32L 40L 48L 56L 64L 75L
Detergent
indicator
Amount of
powder
detergent
10-25g 26-35g 36-50g 51-70g
Another
detergent
amount
When using a liquid or concentrated detergent, follow the
recommendations on the detergent packaging for a top load washing
machine.
Customising a program
This washing machine is equipped with a fuzzy logic function that automatically chooses
certain wash cycle processes for the Custom, Heavy Duty and Quick programs. These do
not require adjustments, however if you wish to adjust these values, complete the following
steps:
1. Prepare your washing according to points 1 to 4 as mentioned in Normal Usage.
2. Press the Power ON/OFF button, then press the Program button to select the
washing program, e.g. Custom or Heavy Duty.
3. Press the Process button to select the process and time you want to adjust. The
relevant indicator light will illuminate when the option is selected. Then press the
Set button and set the option.

17
4. Press the Water Level button and choose an appropriate water level.
5. Close the lid and press the Start/Pause button for the washing program to start.
6. At the end of the washing program, a buzzer will sound to alert you that the
program has finished before the power is shut off automatically.
7. Close the water taps and unplug the power plug from the wall outlet.
Blanket program
Use this program for washing blankets or other bulky items. It will automatically select the
highest water level (75L), but you can adjust this manually down to 48L according to the
size of your bulky item(s).
1. Press the Power ON/OFF button and open the washer lid.
2. Press the Program button repeatedly until the indicator for the Blanket program
flashes.
3. Dissolve an appropriate amount of washing detergent with a little lukewarm water,
then pour the detergent solution directly into the tub of the washing machine.
Note:
If you want to use a customised program on a regular basis, you can program it to the
machine's memory for easy access the next time you want to use the same program.
See 'Memory function', for instructions.
Minutes
Minutes (Soak time can be adjusted for the
Custom, Heavy Duty and Blanket Programs)
Minutes (Except Delicate program, see below)
(The numbers represent the number of rinses)
Minutes for Delicate program

18
4. Fold up the blanket and put it into the washing tub, as illustrated below.
Fold in 2 by
the long side
Fold 4 times in the
same direction
Roll up the
blanket
Put into the wash
tub with the edge
5. Close the washer lid.
6. Press the Start/Pause button for the washing program to start.
7. At the end of the washing program, a buzzer will sound to alert you that the
program has finished before the power is shut off automatically.
8. Close the water taps and unplug the power plug from the wall outlet.
9. It is recommended to cleaning the lint filter after washing a blanket.
Selecting a wash cycle process
On occasion you may want to select a single wash cycle process (or two processes) instead
of a complete program. For example, you may want to spin clothes that got wet from rain
while hanging on the line or rinse and spin clothes washed by hand.
•To set a spin cycle only, set the Soak, Wash and Rinse options to "0" and then select a
Spin time (from 0-9 minutes). Then proceed as described opposite.
•To set a rinse and spin cycle, set the Soak and Wash time to "0", then select a Rinse
option (from 1 to 4) and then the Spin time (from 0-9 minutes). Then proceed as
described opposite.
Note:
If you notice that the blanket floats up during the wash, press the Start/Pause button,
the washer will stop working temporarily. Push the blanket down and press the
Start/Pause button again to continue washing.

19
Preset timer (delayed washing)
This washing machine has a 0-24 hour preset function, which you can set to determine the
time when the washing program will finish. (It is, in effect, like a 'delayed start' function, but
you set the time period after which you want the wash to finish rather than to start.)
1. Put your washing in the machine, loading items uniformly in the tub.
2. Press the Power ON/OFF button.
3. Select the required Program.
4. Press the Process button until the Delay indicator light flashes, then press the
Set button to select the desired time period (in hours) for the wash to finish.
5. Select the water level, if necessary.
6. Add any detergents.
7. Close the washer lid and press the Start/Pause button.
8. After setting the preset, the corresponding light will illuminate and all other lights
will be switched off about one minute later. From this time on until the preset time
only the Power ON/OFF and Set buttons will respond when pressed.
9. To check the preset program, press any button (except for the Power ON/OFF
button); the program will be indicated for 5 seconds. During these 5 seconds you
can press the Water Level button and set the water level.
10. To cancel the preset, shut off the power.
11. To change the preset time, first cancel the preset, then set it again.
Adding detergent to a preset wash
When using the delayed wash, do not add detergent directly to the wash tub.
•Powder detergent: either put powder detergent into the detergent box or, if you prefer
to put it directly into the wash tub, wrap the powder in a small cloth.
•Liquid detergent and bleach: pour liquid detergent or bleach into the hole on the top
plate. Do not pour it directly into the tub as it may cause discolouration of your washing.
•Close the lid and press the Start/Pause button.
Note:
This function is not available for the Normal, Delicate and Quick programs. To avoid
water leakage when using this function, ensure the water taps are open, the drain
hose is properly installed and the washing load and detergent are properly prepared.

20
Load sensor (fuzzy control)
For the Custom and Heavy Duty programs, the machine automatically detects the weight
of your wash load and selects the appropriate water level, wash and spin time and rinse
type. For the Quick program, the machine will automatically choose the water level. You do
not have to set these values; however, if you want to adjust them yourself, see "Preset
Timer" for how to customise processes.
Hot/ cold / warm water wash
This top load washing machine must be connected to both a cold and a hot water tap. You
can then set it to use either just cold water for a cold-water wash or just hot water for a hot
water wash or both hot and cold water for a warm water wash.
To select the wash temperature, press the Temperature button.
•Cold wash: the corresponding indicator light is off.
•Warm wash: the corresponding indicator light is on.
•Hot wash: the indicator light is flashing.
Setting the water level and other processes
You can set the water level for wash and rinse processes. For example, if you are sensitive to
detergent residues in your washing, you may want to select a higher water level for rinsing.