Kognita PC280 User manual

1
PC280 Instruction Manual
Instruction Manual

2
INTRODUCTION
This appliance works well with 800W powerful motor, low noise design, knob control, easy operation. There are
three kinds of professional mixing mode with six-speed settings, show excellent performance. A variety of
accessories can be selected to meet all your demand for the kitchen.
CHARACTERISTIC
1. 800W powerful motor, low noise to work and excellent performance.
2. Six-speed settings.
3. Three kinds of professional mixing mode, with multi speeds option for excellent performance.
4. The front end is equipped with accessories interface, which is convenient to assemble various accessories.
5. Pop up automatic design, detachable mixing container for easy operation.
6. Planetary mixing operation track, no dead corner, more in place.
7. 5.1QT large capacity stainless steel mixing container for more ingredients and food.
NOTES:
Please read carefully and keep the instruction well to check before using this appliance.
ENVIRONMENT
1.Do not use outdoors. It may be caused electric shock under the rain.
2.To protect against risk of electrical shock, do not put mixer in water or other liquid. This may cause personal
injury or damage to the product.
3. Do not operate mixer with a damaged cord or plug or after the appliance malfunctions, or is dropped or
damaged in any manner. If the mixer becomes damaged, please contact after service or technician for help.
4. Do not try to repair the appliance yourself or without the intervention of qualified engineer.
5. Please place the appliance on a stable and flat table. It will cause injury if it is placed on uneven level.
6. Do not place the mixer above or near lit hob burners or electric rings, inside an oven or near other heat
sources.
7.Please do not let the power cord fall from the edge of the table, the power cord winding around the object or
fuselage will make the product fall and cause damaged.
IMPORTANT
1.The mixer is 110V, 60Hz and please check whether the power supply can fit it.
2. Please clean all accessories before first usage.
3. Do not touch power cord、plugs and other electrical parts with wet hands which may lead electric shock.
4. When problem occurs, turn off all controls and remove plug from outlet, and then contact service center or
dealer.
5. Do not use mixer for other than intended use.
6.The use of attachments not recommended or sold by this mixer dealer may cause fire, electrical shock or
injury.
7. During mixing, please don't use the scraper or other tools to concentrate the material in the mixing container,
it may cause involvement or injury.

3
8.Avoid contacting moving parts. Keep hands, hair,clothing, as well as spatulas and other utensils away from
beaters during operation to reduce the risk of injury to persons and/or damage to the mixer.
9.Close supervision is necessary when mixer is used by or near children or incapacitated persons.
10. Please turn to "OFF" setting, and unplug the power plug during installation, removing or cleaning parts,
otherwise it may cause injury.
11. Do not touch the motor part after prolonged using.
12.Do not use the mixer to continue to work for over 24min.To stop and cool it down by 15min. before start it
again.
13. The mixer has an internal safety to prevent overheating. If the mixer shuts down because of overheating,
reset the speed control dial to OFF and unplug unit from wall. Wait 1 minute and plug back in. If mixer still does
not start, wait 30 minutes to allow it to cool completely before turning back on.
14. When one of the output ports is operating, please make sure to remove the parts or components that are
connected to the other output ports and be installed a protective cover.
15. To be careful when mixing hot food or liquid.
16. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
17. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
18. Warn: Potential injury from misuse.
19. Care shall be taken when handling the sharp cutting blades, emptying the bowl and during cleaning.
20. Be careful if hot liquid is poured into the blender as it can be ejected out of the appliance due to a sudden
steaming.
21. Switch off the appliance and disconnect from supply before changing accessories or approaching parts that
move in use.
22. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
23. This appliance can be used by children aged from 8 years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning
and user maintenance shall not be made by children unless they are aged from 8 years and above and
supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
24. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction concerning use of the appliance in
a safe way and if they understand the hazards involved.
Children shall not play with the appliance.
25.This instruction also be available in an altemative website. http://www.link-plus.com.cn/en/index.html
26.In normal work, the mixer can only have one attachment working, other attachments can not work at the
same time.

4
Notes
1. THIS UNIT IS FOR HOUSEHOLD USE ONLY.
2. Do not dump the appliance when it is not in use.
3.Do not leave mixer unattended while it is operating.
4.To check product periodically. Please do not continue to use it if there is any damage.
5.Do not try to repair this product by yourself. You should contact customer service center or send it to special
maintenance site for inspection and maintenance.
6. Please keep this appliance, accessories, all packaging (including outer packing, color box packaging, PE bags,
etc.) away from children.
7. Do not put any unnecessary objects into the container when the machine is running.
8. Unplug from outlet while not in use, before putting on or taking off parts and before cleaning.
9. The machine should be put on a flat and stable platform
10. Do not use the equipment without any food.
11. When using the meat grinder parts, be sure to use the standard food pusher.
12. *Overload caution! Please do not use grinder head or glass jar together with mixing functions.

5
Description for Component
（A）Standard Accessory
1.Top Lid
7. Body
2.Front Lid
8.Locking press button
3.Transverse power take-off
9.Switch knob
4.Stainless steel bowl
10.Beater
5. Bottom cover
11.Dough hook
6.Upper power take-off
12.Whisk
-----------------------------------------------------------------------------------------------------------------------------------------------------
（B）Accessories
Function：Mincer,Sausage,Juicer
1.Food Pusher
10.Plastic plate
2.Food Tray
11. Plastic plate cover
3.T-Tube
12.Sausage
4.Snake
13.Small circular knife
5.Cutting Blade
14.Flat surface knife
6.Cutting Plate（medium）
15.Great circle surface
knife
7. Cutting Plate（coarse）
16.Macaroni knife
8. Fixing Ring
17.Chopping
vegetables suite
9.Juice jar
18.Squeeze juice suite

6
Description for using
Description for Standard Accessories
The standard parts of this machine are composed of dough hook, whisk, beater and stainless steel bowl.
Installation and dis-assembly of mixing head Installation
1.Insert the bowl cover to insert the notch at the upper
end of the dough hook to the driving shaft
2.Push the dough hook upward and
turn counterclockwise until it cannot move.
(figure A)
To remove attachments
1.Push the dough hook upward and turn clockwise until it cannot move.
2.Take the dough hook out and and remove the transparent lid.
（figure B）

7
Mixing bowl
1.Keep the appliance in a safe, stable, clean and dry place
2.One hand hold on the head of the machine, another hand press the locking press button, the appliance will
automatically lift the head, and we can make the appliance head to the maximum position by hand and install
bowl cover.
3.Installing the dough hook to the specified position according to above installing method.
4.Place the stainless steel bowl in the specified position and lock it clockwise.
5.Do not exceed the bowl’s maximum capacity so as not to overload the appliance.
6.Ready and press down the appliance head to lock (the locking press button will pops up) to recover the
head position.
7.Switch on the 110V，60Hz safety power.
8.Use the speed control dial of the mixer to help you find the correct speed to use.
9.When the mixture reaches the desired range of agitation, turn the speed knob to the "OFF" and unplug the
power plug.
10.Turn the stainless steel bowl counterclockwise and remove it from the machine.
11.Take out the mixture from bowl.
12.The cleaning of parts can be carried out in the light of the methods described in "cleaning and
maintenance".
P.S.：
a .Before using this product, please clean the accessories with detergent, rinse it with water and leave it dry and
ready
Dough Hook
Dough Hook use for mixing bread, pasta, Chinese pasta and other dense foods
1. Choose the Dough Hook , install the Dough Hook and the stainless steel bowl according to the steps
described before, add the dry yeast and liquid material after adding the flour which needs stirring.
2. When fully installed, turn the switch knob to the 1 gear and observe that when the flour has been rolled,
rotate the switch knob to the 2 gear until the dough has a good elasticity or the gluten needed.
Beater
For use, mixer mixing medium density food such as cake, pie, cookie dough, butter,jujube paste cake etc.that
produced using low gluten flour.
1. Choose the beater. According to the steps described before, install the beater and the stainless steel bowl.
Add the ingredients that need stirring.
2.After fully installed, plug in the power cord and turn on the switch knob. Before mixing the ingredients,
adjust the switch knob to 1 gear, and gradually increase to the desired speed as the mixing process.
Whisk
Used for mixing materials when mixed with air, such as: the production of protein cream, salad sauce, cream
puffs, Sponge Cake, etc.
1. Please wipe the stainless steel pan and egg whisk to make sure there is no water or oil.
2. According to the steps described before,rotary whisk and install the egg whisk and stainless steel pot, and
put in the necessary mixing of the protein (There must not have a little yolk in the protein).
3. After fully installed, plug in the power cord and turn on the speed control knob to the 5 gear, so that the
protein is sent to the desired degree of curing.

8
Foaming state at different stages
First step
The bubbles are very big and uneven
Begin step
The bubbles become fine and turn white
Wet foaming
Raise the whisk and then the bubbles can stand up and its front end is
downward
Slightly curing
Raise the whisk and its front end is very sharp and soft
Dry foaming
Raise the whisk ,which have sharp angle with uniform color and luster
Curing and dry steps
Raise the whisk,which have sharp angle with uniform color、mottled and
without luster.
Production of cream
1.Refrigerate the stainless steel pan for about 20 minutes
2.Choose whisk,according to the steps described before and stall shell
Breaking,frozen stainless steel pot and put in fresh cream and sugar.
3.After fully installing,plug on the power cord and turn on the speed
control knob to 4 gear,then stirring until the desired level of cure.
Bubble state at different stages
Primary period
Mix well and it will begin to thicken
Appearing pattern
Raise the egg whisk and erect the sharp angle. It can be mixed with other materials and
solidified properly
curing
The angle of creamy foam can be fully set up, and reach
the curing level that cake,ice cream and puff needs
Notes:
1. The curing of butter only changes in a matter of seconds.
2.In order not to pass excessively, please keep observe from the stage of appearance.

9
Instruction for chosen accessories
Mincing:
1.Hold on the T tube and put the snake into tube.
2.Place the cutting blade on the snake with the sharp upward.
3.Select plate(coarse/medium/fine)that you need on the cutting blade.
4.Tighten the Fixing ring.
5.Open the front cover of the machine and insert the assembled attachments into the machine's crosswise
output end
6.Place the food tray on the inlet of the meat grinder.
7.Place a container at the meat outlet, cut the meat into small pieces, place it on the food tray, push the food
pusher and open the machine.
Notes:
1.Please use food pusher to push food into the feed port, and do not use finger or other utensils to transport
food.
2.It will be better to cut the meat in small pieces.
3.When using grinding head, it is necessary to remove the mixing parts from the stainless steel bowl
Caution: Do not put the meat with skin tendon or bone into the grinder.

10
Sausage:
1.Hold the T tube and put the screw into mincing tube.
2.Place the blade and the appropriate cutting plate and sausage holder on the screw in turn and tighten the
fixing ring.
3.Open the front cover of the appliance, insert the barrel of meat in the transverse port of the end, turn
counterclockwise and righting.
4.Soak the casing in cold water for 10 minutes, and gently cover it on the sausage shaper.
5.Place the meat on the plate and push the meat into the meat grinder with the food pusher. Turn on the
machine, stir the meat into the casing, and if the casing gets stuck, wipe it off.
6.The sausage is filled with nodes then finish.
Warning！
Attention！Stuffed sausages maybe swell when boiled or fried, and sausages can tear!Please use the pusher to
push the meat into the feed port, and do not use finger or other utensils to deliver the food!

11
KEBBE：
1.Hold the T tube and put the snake into tube.
2.The plastic plate and plastic cover are successively arranged on the screw and tighten the fixing ring.
3.Before opening the front cover of the appliance, insert the set of mincing rolls into the head tube of the
lateral output port, turn counterclockwise righting.
4.Mix the mutton and wheat flour, place it on the food tray, push it into the meat grinder with a food pusher,
turn on the machine and mix the ingredients to form a hollow doughnut through the extrusion of the meat
paste.
5.Cut the doughnut into the required length. Each small circle can be filled with meat which is well blended
with the taste. The edges of the face ring are tightly pressed and sealed
6.Place the meat pie in the pan until it is deep fried and well done.
Notes:
This accessory can be use to make meat pie,fishing dumpling and other typical food.
Warning！
Please use the pusher to push the meat into the feed port, and do not use finger or other utensils to deliver the
food!

12
Blender jar：
Notes: the maximum scale of cup is 1.6QT (rated capacity: 1.4QT)
Assembling:
1.Hold the glass jar handle into the output connector, rotate it clockwise to lock.
2.Lower the machine head in a horizontal position, the locking rotary knob will popup automatically and lock
the head.
3. Open the head cover
Usage of the juicer
1.Put the sliced fruit cube into the glass jar, add some water or milk or some other liquids, cover the lid.
2. Open the lid, put the glass jar in the output connector and lock the jar clock wisely.
3. Put the food into the glass jar
4. Cover the lid
5. After the installation is complete, plug in then adjust to 6th level, till the idea effect.
6. Plug in and the machine is on, if the fruit cubes are in big size, use the P level for 2 or 3 seconds, then adjust
to proper speed.
Cautions
1. Make sure the machine is off before install the glass jar
2. P level can not be stay for a long time, but can be repeat operated.
3. Do not turn on the machine for more than 30s while the glass jar is empty
4. Do not put food into the glass jar exceed the capacity
5. The juicer jar is glass, water over 104℉is not allowed.

13
Squeeze the noodles:
1. Hold the t-shaped screw and put the minced screw into the t-shaped screw.
2. Select the required noodle knife board (large round surface knife, small round surface knife, flat surface
knife, hollow surface knife) and put it on the meat screw.
3.Tighten the big nut.
4. Open the front cover of the machine, insert the assembled minced meat accessories into the interface of
the machine's horizontal output end, and rotate counterclockwise.
5. Place the food plate on the t-shaped screw inlet.
6. Place a container at the exit of the noodles, place the dough on the food plate, push the PE stick in, and
start the machine.
Notes:
1.Please use food pusher to push food into the feed port, and do not use finger or other utensils to transport
food.
2.It is best to divide the dough into small pieces.
3.When using grinding head, it is necessary to remove the mixing parts from the stainless steel bowl

14
Chopping vegetables：
1. First install the dish cutter into the host, then select the dish cutter effect you need, and install the 1, 2 or 3
cups into the dish cutter respectively.
2. Prepare a special cutting stick and place a plate under the cutting tin.
3. When everything is ready, you can start to cut vegetables, start the main machine, see the cutting cup is
rotating, put the material into the top of the cutting tube, and press down with the cutting push plug, you can
get all kinds of cutting effects respectively.
Note:
this set of cutting equipment can make the effect of slicing, shred and mashed potato respectively. Before
operation, please cut the vegetables and fruits with a knife to the size and shape suitable for putting them into
the cutting inlet.

15
Squeeze juice:
1.Place the plastic screw locking ring into the sleeve.(fig.1)
2.Place the gauze into the sleeve next to the plastic screw locking ring.(fig.2)
3.Put the fixing ring through the sleeve and make it at the end of the sleeve.(fig.3)
4.Place the snake into the head, long end first, and turn to feed the snake slightly until it is set into the motor
housing.(fig.4)
5.Insert the shaft of the snake into the central axis of the screw.(fig.5)
6.Put the whole sleeve along with the fixing ring through the screw, then move the fixing ring clockwise so
that it being fastened tightly.(fig.6)
7.Put the plastic juice tray through the sleeve and make it on the suitable position.(fig.7)
8.Insert the plastic screw into the hole of the sleeve, then move it clockwise until it is properly fastened. Then
place the plastic cover onto the sleeve.(fig.8)
Now the appliance is ready for juicing.

16
The cleaning of motor housing
1.Please unplug the power cord before cleaning.
2.Do not wash the mixer to avoid electric shock.
3.Wipe the mixer head, stand, bowl locking plate and unit base with a damp cloth, then dry.
4.DO NOT IMMERSE THE STAND MIXER IN WATER.
5.Do not use sharp or abrasive cleaner, as they may damage the finish of the mixer.
Clean your mixer
1.To clean mixing parts, stainless steel bowl and other accessories cleaning, be sure to turn speed control knob
to "OFF", so that the machine stopped and the power plug removal, otherwise it may cause an electric shock or
injury risk.
2.The mixing parts and stainless steel bowl can not be cleaned by dishwashers. If heat sources or corrosive
detergents are used, they may be deformed or discolored
3.The parts that connected with food can be washed with detergent, and washed with water.
4.Some parts can be separated to wash and must be install again when they are completely dried.
Specifications and parameters
This appliance has been tested by Relevant International Requirements, such as EMC, Low Voltage Instructions,
Safety Technical Regulations, etc..
Description
Model No.
Voltage
Power
Capacity
Muti-funional Stand
Mixer
SM10280
110V/60Hz
Rated power input
for blender: 800W;
Beater: 350W；
Mincer：250W
5.1 QT
Recipe
Function
Recipe
Speed
Operate time
Food blender
1.19lbs carrots +
1.79lbs water
Speed 6
1min
Kneader
3.70lbs flour +
2.67lbs water
Speed 1-6
2 min
Egg beater
0.85QT cream
Speed 2-6
2min
4-16 egg white
Speed 6
4-6min
Beater
Flour 0.22lbs
Sugar 0.22lbs
Butter 0.22lbs
Egg 2pcs
Speed 1-6
3-5min
Mincer
3.31lbs beef
Speed 3-6
3min

17
Question and Answer
Phenomenon
Reason
Methods
The machine suddenly stop
working
Whether the machine is running
too long or the temperature is too
high, resulting in motor
overheating, and power failure
Turn the speed control knob to
"OFF" and remove the power plug
until the machine is completely
cooled.
Turn the speed knob and the
machine does not work
Whether the power failure
Operate after incoming electric
Whether the head is locked
Let the front of head in a horizontal
position
Whether the plug is plugged into
the socket.
Be sure that the plug is
plug into socket.
machine or motor sound in motion
A loud increase in speed or load
during a mechanical operation
May overload or use too long,
please adjust the amount of mixing
and rest after use
Motor speed down
Whether it is used in low
temperatures and it will harden the
oil in the machine;whether the mix
will cause the motor to load too
much
No-load 5 minutes, so that soft
lubrication, so that the speed
stability. Reduce the amount of
agitation and reduce the load. And
turn the speed to the low position
Motor unstable
Motor doesn't
work

18