Kohler Mira Ascend Series User manual

1
1317134-W2-B
These instructions must be left with the user
Installation Guide
Frameless Quadrant Enclosure

2
1317134-W2-B
Safety Information
1. Careshouldbetakenwhendrillingintowallsandoorstoavoidanyhidden
pipes or wires.
2. Westronglyrecommendthatallglasspanelsaremovedbyaminimumoftwo
peopleandthatanyprotectivepackagingalongtheglassedgesiskeptinplace
foraslongaspossibletopreventdamagebeforeinstallation.
3. Wearprotectivefootwearwhenliftingpanels.
4. Wearsafetyglasseswhendrilling.
General
1. Read all of these instructions and retain this guide for later use.
2. Passonthisguideintheeventofchangeofownershipoftheinstallationsite.
3. Follow all warnings, cautions and instructions contained in this guide.
4. Removeallprotectivetapefromtheenclosurebeforeinstallation.
5. Excessiveowratesmayleadtooverowingandleaking.
6. WaterSpraymayextendbeyondtheentranceofwalk-inenclosuresandwe
recommend tiling of the adjacent area.
7. We recommend a drainage test is carried out to ensure the waste is adequate
fortheowdelivered.
8. Doorsthatopenoutwardsmaydripwaterontooor,ensuretheoorcovering
willnotbeaffectedbywater.
9. Walkinsanddividerpanelsaredesignedtominimisewaterescapingoutside
theenclosurebutbytheirverynaturearenotfullywatertight.
Introduction
General Information
ThankyouforpurchasingaqualityMiraproduct.Toenjoythefullpotentialofyour
newproduct,pleasetaketimetoreadthisguidethoroughly,havingdoneso,keep
ithandyforfuturereference.
Thefollowingpagesaimtoprovidecomprehensive installation instructions, plus
adviceonhowtocareandmaintainyourproduct.
Werecommendthattheunitisinstalledbyaqualiedplumberorengineer.

3
1317134-W2-B
Before Fitting the Enclosure
1. Ensurethetrayislevelandwallsareverticalandsquare.
2. Shower ttings should be positioned such that water discharges down the
centre line of a bath or across the opening of a shower cubicle door.
3. Ensure water is not directed at the shower door or side panels. This could result
inwatersprayingoutsideoftheenclosure.
4. Ensurethedooropeningispositionedcorrectlyandisadequateforallusers.
5. Ensurethereisacompletesiliconesealbetweenthetrayandnishedwall.
6. Ensure the door is undamaged and no parts are missing.
7. Ensurethesizeofdoor/panelissuitablefortheinstallation.Temperedsafety
glass cannot be cut.
8. Ensure nothing can impact the door or glass panels during operation.
When Fitting the Enclosure
1. Thewallchannelsmustbeinstalledontoatiledorwaterproofnishedatand
evenwallsurface.Failuretodosowillresultinanunsatisfactoryseal,which
maycausepropertydamage.
2. Werecommendourenclosuresarettedontoshowertrays.
Warning!Theuseofgrout/tilecleaners,scaleremovers,abrasivescourers,
drainunblockersandotherpowerfuldetergentsmayleadtodamageofmetallic,
platedandplasticsurfaces,includingthetrayandshowerwaste.
Use of the Enclosure
1. Highwaterpressureandowmayleadtoexcessivesplashingcausingwater
to escape outside of the enclosure.
2. Incertaincircumstancessuchascleaning,watersprayeddirectlyattheseals
mayescapeoutsideoftheenclosure.
3. With any walk in or open ended enclosure, splashing may cause water to
escape outside of the enclosure.
Yourenclosurehasthebenetofourguaranteewhichstartsfromdateofpurchase.
For terms and conditions refer to the guarantee booklet packed with the product.
Guarantee

4
1317134-W2-B
Domestic ü
Light Commercial ü
HeavyCommercial û
Healthcare û
Recommended Usage
Tools Required
6.0 mm

5
1317134-W2-B
Pack Contents
X 8 qX 8 q
X 1 qX 1 q
X 1 q
(4.0 mm)
(3.0 mm)
X 2 q
X 8 q
Top Carriers Bottom Carriers
Glass lintel brackets
andcovers
X 2 q
X 2 q
X 2 q
X 2 q
X 4 qX 8 q
X 4 q
X 2 q
X 2 q
X 2 q
X 4 q

6
1317134-W2-B
X 2 q
X 2 q
X 2 qX 1 q
X 1 q
X 1 q
X 1 q
A

7
1317134-W2-B
X 1 qX 1 q
B

8
1317134-W2-B
Installation
Note!Coverthetraywastetopreventthelossofsmallparts.
Note!Protectthetraysurfaceduringenclosureinstallation.
Note!
Makesurethatthewallshave
beentileddowntothetray.
MakesuretheTrayisleveled.
Makesurethewallsareatand
square.
(a) Installtheshowertrayinaccordancewiththemanufacturer’sinstructions.
Caution!Makesurethattheshowertrayislevelinalldirectionsandthatthe
wallsareverticalandsquare.
a
b
± 0 mm
1

9
1317134-W2-B
Adjustment Dimensions
Note! All dimensions shown are in mm.
Min/MaxFrameAdjustment Enclosure Size MinimumX(mm) MaximumX(mm)
20 900 x 900 870
870
890
890
20 1000 x 800 970
770
990
790
20 1000 x 1000 970
970
990
990
20 1200 x 900 1170
870
1190
890
Door Conguration Table (ALWAYS AS BELOW)
900 X 900 Openstowardscurved(larger)panel
1000 X 1000 Openstowardscurved(larger)panel
1000 X 800 Openstowardscurved(larger)panel
1200 X 900 Openstowardscurved(shorter)panel
X(From Tiled Wall)
X
(From Tiled
Wall)

10
1317134-W2-B
b
c
a
d
x4
x4
6 mm
± 0 mm
x4
x4
2
6.0 mm
(a) Positionthewallchannelonthewallusingthedimensionssuppliedintheabove
tableonpage10forcorrectenclosuresize.Usingaspiritlevelmakesurethat
it is upright.
(b) Markthepositionofthexingholes,thenremovethewallchannel.
(c) Drill with a 6 mm masonry bit (not supplied) and plug using the wall plugs
(supplied).
(d) Position the wall channel on the wall and partially install the xing screws.
Ensurethatthescrewheadspacersarettedtothescrews.
(e) Applysiliconesealantaccordingtothemanufacturersinstructionsalongthe
length of the wall and at the bottom of the wall channel.
(f) Ensurespacersareonthescrews.Fullytightenthexingscrews,makingsure
that the wall channel is upright.
Screw Head
Spacer
Note! Ensure longer face of wall channel is on the outside of the
enclosure.
Note! Trimwallplugstonishedwall
surface, as wall channel will not sit
atiftheyareproud.
Note!Usehandscrewdriveronlyto
avoiddamagetoplasticspacers.

11
1317134-W2-B
6.0 mm
3
b
c
a
d
x4
x4
6 mm
x4
x4
(a) Position the second wall channel on the wall using the dimensions supplied
intheabovetableonpage10forcorrectenclosuresize.Usingaspiritlevel
make sure that it is upright.
(b) Markthepositionofthexingholes,thenremovethewallchannel.
(c) Drill with a 6 mm masonry bit (not supplied) and plug using the wall plugs
(supplied).
(d) Positionthewallchannelonthewallandpartiallyinstallthexingscrews.
(e) Applysiliconesealantaccordingtothemanufacturersinstructionsalongthe
length of the wall and at the bottom of the wall channel.
(f) Ensurespacersareonthescrews.Fullytightenthexingscrews,makingsure
that the wall channel is upright.
± 0 mm
Screw Head
Spacer
Note! Trim wall
plugstonished
wall surface, as wall
channel will not sit
atiftheyareproud.
Note! Ensure longer face of the wall channel is on outside of the
enclosure.
Note! Use hand
screwdriveronlyto
avoiddamagetothe
plastic spacers.

12
1317134-W2-B
4
(a) DecideonwhetheryourdoorwillbeLHorRHopening.
(b) Install the top and bottom carriers as shown in the above diagram.(pre
assembled in parts pack)
(c) Installthebottomcarrierslooselyondoor.
(d) Installthecoversontoallthecarriers.
(e) Toaidassemblylater,placetheassembleddoorinsidetheenclosure/tray
area(leancarefullyagainstwall).
x2
Note! The door on the enclosure is reversible and can be
altered to suit your conguration. See the door opening
table on page 9 for your door opening options
Note! Ensure carriers are mounted
levelandstraightontheglass.
Note! Slider blocks should be on
theouterofthecurve.
x2
3.0 mm

13
1317134-W2-B
b
a
b
12 mm
c
d
(a) Use the glass lintel bracket as a guide, place at the end of the glass panel, as
illustrated.
(b) Push gaskets onto the glass and up to glass lintel bracket to get your
measurement. (12 mm as shown)
(c) Removeglasslintelbracketforlateruse.
5Prepare the xed panels for installation, tting the panel gaskets.
Note! Smallnongasketstoface
INSIDE of enclosure.

14
1317134-W2-B
6
b
b
c
1
2
3
4
d
(a) Select the lintels for top and bottom as per
 yourglassconguration.
(b) Place the opening and closing glass panels
into the wall channel while positioning on the
bottom lintel with cutouts on glass.
(c) Place the back plates on the internal side of glass on both panels and tighten
the two screws on each side.
(d) Screw the 2 glass lintel brackets into place onto the bottom lintel.
(e) Makesureproperalignmentofthetwoglasspanelsandthebottomrail
alongthetray.
(f) MakesurethatglasspanelsaresetinsideLshapebracket.
(g) Insert the glass lollipops spacers (1) with serrations facing inside unit.
(h) Placeretainingblock(2)overtheglass.
(i) Fit the screws (3). (j) Fitthecover(4).
x2 x2
x4
Glass lintel
bracket
3.0 mm
Note! Be careful not to
lose the lollipop down the
wall channel.
Note! The lollipop must
sit within the thickness of
the glass, pushing it too
far in will result in the top
bracket not being able to
locate down.
Note! Push the narrow side of the
coversonrst,tightlytting.
± 0 mm

15
1317134-W2-B
± 0 mm
a
b
d
(a) Position the top lintel with the cutouts on the glass.
(b) Place the back plates on the internal side of glass on both panels and tighten
the two screws on each side.
(c) Usingaspiritlevelmakesurethatbothglasspanelsareuprightandthetop
lintelislevel.
(d) Screw the two glass lintel brackets into place onto the top lintel.
x2 x2
x4
± 0 mm
7
3.0 mm
Fitting the top lintel
Note! Shouldyourtop
lintelnotbelevel,you
can use the packers
(supplied). See next page
for details.

16
1317134-W2-B
(a) Loosen the screws and pull up the top lintel.
(b) Locate the support packer onto the gasket.
(c) Pullbackthetoplintelandmeasurethelevel.
a
b
± 0mm
c
Support packers for top lintel level
Afterpositioningthetoplintelwiththecutoutsontheglass,youneedto
ensurethelevelbeforefullytighteningthetwoscrewsoneachside.The
supportpackersareanoptiontogetthelintelfullylevel.Pleasefollow
steps below to install the support packers.

17
1317134-W2-B
8
H2O
H
2
O
(a) Pushinthebeadingsealsusingtherollerprovidedforbothchannelsonthe
inside of the enclosure, starting at the bottom and working upwards.
(b) Makesurethatboththeglasspanelsarelevelandequalaboutthetray.
± 0 mm
Important!
Wet the beading seal to
help with installation.
Note! Prior to beading, ensure
thattheglasspanelsarelevel
withtheedgesofthetray.
The ribs on
the beading go
towards the glass.
Insideview
Insideview

18
1317134-W2-B
9
(a) Turntheslidingdoor(pre-installedwithcarriers)soitisinthecorrectorientation.
As determined in step 4.
(b) Mounttheslidingdoorontothetoplintel.
(c) Carefullypushthebottomdoorcarriersintothebottomlintel,pressingdown
on the carriers as required.
(d) Adjustthedoor level byrotatingtheadjustment screws ontopofthe door.
Clockwise=LowerDoor.Anti-clockwise=RaiseDoor.
(e) Thebottomcarrierscanbeadjustedindividually.Ifrequiredloosenthebolts
andmovethecarriersupordownontheglass,whenthedesiredpositionis
achievedre-tightenthebolts.
(f) Oncealladjustmentshavebeenmade,ensurethedooredgesarevertical.
a
h
c
b
4.0 mm
b
RaiseDoor-AntiClockwise
LowerDoor-Clockwise
Note! Ensure that
lintel is free from
debris.
Note! Avoidover
adjustment of the
levelingscrews.
This will ensure
there is no contact
between the lintel
and the metal
slider carriages. Note! Apply the supplied
lubricant in the three
marked locations. This is
critical to ensure smooth
operation of the door.
Move the door left and
right to distribute the
lubricant over the length of
the track.
d
g

19
1317134-W2-B
(g) Fitcarriercovers.
(h) Apply the supplied lubricant within the trackway of the lintel at the 3 spots
detailedabove.Movethedoorleftandrighttodistributethelubricant.
(a) Fit anti jump strip on the top lintel.
VIEW FROM INSIDE OF ENCLOSURE
Anti Jump Strip
10

20
1317134-W2-B
11 Handle Installation
2.0 mm
a
c
b
Note! Handle installations are the same for all the handle options.