Kohler K-1025-H2 User manual

Homeowners Guide
8-Jet Personal Hydro-Massage System
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de Mcorresponden a México
(Ej. K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-1025-H2 K-1035-H2, K-1036-H2
1032110-5-D

Important Information
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,
ELECTRICAL SHOCK, OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: When using electrical products, basic precautions should always be followed,
including the following:
DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this
product unless they are closely supervised at all times
WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the
unit.
WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,
telephone, radio, or television) within the enclosure.
WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical
history should consult a physician before using this product.
Use this product only for its intended purpose as described in this manual. Do not use attachments not
recommended by the manufacturer.
Never drop or insert any object into any opening. Keep small objects such as bath toys and bathing
accessories out of the product while the unit is running.
Do not operate this product without the guard (cover) over the suction fitting.
This installation must have two Class A Ground-Fault Circuit-Interrupters (GFCIs) or Residual Current
Devices (RCDs). The GFCIs or RCDs protect against line-to-ground shock hazard. Use two 220/240 V, 20 A,
50/60 Hz dedicated services; one for the pumps and controls, and another for the heater. Such a GFCI or
RCD should be provided by the installer and should be tested on a routine basis.
To test the GFCI or RCD, press the test button. The GFCI or RCD should interrupt power. Press the reset
button. Power should be restored.
If the GFCI or RCD fails to operate in this manner, the GFCI or RCD is defective. If the GFCI or RCD
interrupts power to the bath without the test button being pressed, a ground current is flowing, indicating
the possibility of an electric shock. Do not use.
Disconnect the product and have the problem corrected by a qualified service representative before using.
WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs
when the internal temperature of the body reaches a level several degrees above the normal body
temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal
temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia
include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c)
unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to
exit the bath, and (f) unconsciousness resulting in the danger of drowning.
IMPORTANT! Flush the system twice a month or more depending upon usage, as described in the ″Care
and Cleaning″section.
Do not allow the water temperature in the product to exceed 104°F (40°C).
Do not use shampoo, soap or bubble bath in the product water. You can freely use shampoo and soap for
showering before you fill the footbath basin.
1032110-5-D 2 Kohler Co.

Important Information (cont.)
This product has been listed by Underwriter’s Laboratories, thus ensuring safety for you and your family.
This product also conforms to rigid ANSI and IAPMO standards set with the plumbing industry.
Thank You For Choosing Kohler Company
Thank you for choosing Kohler Company. Your Kohler Company product reflects the true passion for design,
craftsmanship, artistry, and innovation Kohler Company stands for. We are confident its dependability and
beauty will surpass your highest expectations, satisfying you for years to come.
All information in this guide is based upon the latest product information available at the time of
publication. At Kohler Company, we strive to fulfill our mission of improving the level of gracious living for
each person who is touched by our products and services. We reserve the right to make changes in product
characteristics, packaging, or availability at any time without notice.
Please take a few minutes to review this guide. Pay special attention to the care and cleaning instructions.
Kohler Co. 3 1032110-5-D

Features
Your Kohler personal hydro-massage system is the ultimate custom hydro-massage system. The exhilarating
spray will stimulate, invigorate, and energize your body.
•Lighted User Keypad - Located within easy reach, the lighted user keypad allows you to control the
hydro-massage system and regulate the water flow of the bodyjets.
•Pump/Motor - Provides quiet, variable speed power to circulate the water and create the
hydro-massage action. The pump/motor will deliver up to 80 gallons (303 L) of water each minute.
The system recirculates water up to two times per minute.
•Bodyjet valves - Conveniently located on the face of the tower to offer quick, the bodyjet valves
allow easy control over your hydro-massage. The top bodyjet valve opens and closes the center
array of two bodyjets. The bottom valve controls the bottom set of four bodyjets. Open or close
these valves to customize your hydro-massage needs.
•Heater - To enhance your experience, the heater automatically helps to maintain the temperature of
the water up to 104°F (40°C). The heater turns on automatically when the hydro-massage system is
operating, and turns off when the pump motor is turned off. The heater may be manually turned off
using the keypad at any time while the pump is operating.
Lighted User Keypad
Available modes will be illuminated in blue. Active modes will be illuminated in green.
Power Turns the keypad, hydro-massage system pump, and heater on or off.
Heater Automatically engages when the power icon is selected. Press the heater icon to turn the
heater off. Press the icon again to turn the heater back on. The heater will help maintain
the water temperature up to 104°F (40°C).
Up Arrow Increases the water flow of the bodyjets.
Down Arrow Decreases the water flow of the bodyjets.
Indicator Bar Displays the water flow volume of the bodyjets.
Heater
On/Off
Power
On/Off
Decreases
Flow
Increases
Flow
Lighted User Keypad
Indicator Bar
1032110-5-D 4 Kohler Co.

Operation
Please read and follow these steps carefully so you can safely enjoy the benefits of your hydro-massage
system.
Before Use
Remove all loose bathing items (such as soap bars, shampoo bottles and washcloths) from the direct
water path.
Remove your eyeglasses or contact lenses and any loose jewelry before entering the enclosure.
Operation
WARNING: Risk of personal injury. Always stand off to the side of the bodyjets when you turn on
the hydro-massage system. The stream of water can be very powerful.
NOTE: Do not allow shampoo, soap, or bubble bath to the enter the foot bath basin. If desired, shower
using shampoo and soap before filling the footbath basin with water.
Close the enclosure door securely.
Fill the foot bath basin with tempered water (not to exceed 104°F (40°C)) to a level at least 3″(7.6
cm) above the top of the suction cover. Use your hand to check the water temperature in the basin
before activating hydro-massage system.
Press the power icon on the lighted user keypad to turn the hydro-massage system on. After several
seconds, water will begin flowing at the lowest water pressure setting.
Allow the water to flow for several seconds to regulate the water temperature, then enter the foot
bath basin.
Gradually increase the water flow by pressing the up arrow on the lighted user keypad.
NOTE: After 20 minutes of continuous use, the hydro-massage system will automatically shut off. To
reactivate the system, step to the side, then press the power icon on the lighted user keypad. Reenter the
basin area.
If you wish to use the hydro-massage system after it has automatically shut down, simply step to
the side and press the power icon on the keypad to restart the system.
Care and Cleaning
Flush Hydro-Massage System
NOTE: Sanitize your system by flushing it twice a month or more, depending upon usage. To do this:
•Fill the footbath basin with hot water to a level 3″(7.6 cm) above the top of the suction cover.
Suction
Cover
Foot Bath
Basin
Keypad
Tower With
Bodyjets
Kohler Co. 5 1032110-5-D

Care and Cleaning (cont.)
•Add two teaspoons of low-foaming dishwasher detergent and 1/2 cup (115 ml) of household bleach
to the water.
•Run the hydro-massage system for 5 to 10 minutes with all eight bodyjets running at the same time.
Turn off the system and drain the water.
•Fill the footbath basin with cold water to a level 3″(7.6 cm) above the top of the suction cover. Run
the hydro-massage system for an additional 5 to 10 minutes with all eight bodyjets running. Drain
the basin and wipe dry with a clean, soft cloth.
For best results, keep the following in mind when caring for your KOHLER product:
Exterior Surfaces
•Use mild soap and water to clean the unit. Wipe the entire surface dry with a clean, soft cloth.
Many cleaners contain harsh chemicals, such as ammonia, which can adversely affect the finish and
are not recommended.
•Do not use abrasive cleansers or solvents on the unit.
Tower
•Always test your cleaning solution on an inconspicuous area before applying to the entire surface.
•Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.
•Do not allow cleaners to soak on surfaces.
•Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring
pad to clean surfaces.
Walls and Basin
•Various wall and basin materials require different cleaners and cleaning methods. Follow the care,
cleaning and maintenance instructions furnished by the wall and basin material suppliers and
manufacturers.
Door
NOTE: For door enclosures not manufactured by Kohler Co.: Follow the care and cleaning instructions
furnished by the door enclosure manufacturer.
•Always test your cleaning solution on an inconspicuous area before applying to the entire surface.
•Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.
•Do not allow cleaners to soak on surfaces.
•Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring
pad to clean surfaces.
For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &
Cleaning information, call 1-800-456-4537.
One-Year Limited Warranty
ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year
from date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection
discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not
responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home
Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI
53044, USA, or by calling 1-800-4KOHLER (1-800-456-4537) from within the USA and Canada, and
001-877-680-1310 from within Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS
1032110-5-D 6 Kohler Co.

One-Year Limited Warranty (cont.)
WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how
long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,
so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You
may also have other rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.
One-Year Warranty
KOHLER CO.
It is recommended that at the time of purchase, you verify that all accessories and components are complete
in this package.
This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the
date of purchase as shown on the invoice or receipt.
1. Kohler Co. will only service its commercialized products through its authorized distributors.
2. To obtain warranty service, please present the invoice and corresponding warranty.
3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new
replacement or an equivalent model (in those cases that the model has been discontinued) when the product
is beyond repair, without any charge to the consumer.
4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.
5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may
substitute the warranty in the case that there is a discrepancy in the validity of the warranty.
EXCEPTIONS AND RESTRICTIONS
The Warranty will not be valid in the following cases:
1. When the product is not operated in accordance with the instructions concerning use and operation set
forth in the owner’s manual or installation instructions, and when the recommendations and warnings
included are not observed.
2. When the product has been modified or dismantled partially or totally; or has been used in a negligent
fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not
authorized by Kohler Co.
3. This warranty does not cover the damages as a result of disaster such as fire or acts of God, including
flooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can
exercise your rights under this warranty, please call 001-877-680-1310.
KOHLER CO., KOHLER, WI 53044 U.S.A.
IMPORTER:
INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V.
AV. CARLOS PACHECO NO. 7200
CHIHUAHUA, CHIH., MEXICO C.P. 31060
TEL: [phone]
Troubleshooting
This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualified
electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale
distributor.
Kohler Co. 7 1032110-5-D

Troubleshooting (cont.)
Symptoms Probable Causes Recommended Action
1. Unit does not start or
stop. A. No power to pump/receptacle/keypad. A. Set/Reset GFCI or RCD. Check wiring. Refer to installer/dealer.
B. Harness is blocked. B. Remove blockage.
C. Keypad disconnected from
pump/control box. C. Reconnect keypad and/or wiring harness.
D. Keypad doesn’t work. D. Replace keypad. Refer to
installer/dealer.
E. Not enough water in footbath
basin. E. Fill basin 3″(7.6 cm) over top of suction cover.
F. Motor/pump assembly does not
work. F. Replace motor/pump assembly. Refer to installer/dealer.
G. Control does not work. G. Replace control. Refer to
installer/dealer.
2. Water flow surges. A. Not enough water in footbath
basin. A. Fill basin 3″(7.6 cm) over top of suction cover.
B. Suction is blocked. B. Remove obstruction.
C. Harness is blocked. C. Remove blockage.
3. Motor starts, all bodyjets
are not functioning. A. Bodyjet is blocked. A. Remove blockage.
B. Bodyjet wiring loose or damaged. B. Identify source of fault and
correct or replace wiring. Refer to
installer/dealer.
C. Not enough water in footbath
basin (pump cavitates). C. Fill basin 3″(7.6 cm) over top of suction cover.
D. Keypad does not work. D. Replace keypad. Refer to
installer/dealer.
E. Control does not work. E. Replace control. Refer to
installer/dealer.
4. Unit stops automatically
before 18 minutes. A. GFCI or RCD has tripped. A. Set/Reset GFCI or RCD.
B. Motor overheated and protection
device activated. B. Check for restricted air space around pump box, motor vent
blockage, suction/harness
blockage. Correct and allow
motor to cool.
5. Unit does not stop
automatically after 22
minutes.
A. Timer mechanism accidentally
deactivated. A. See Service Manual. Refer to installer/dealer.
6. Noisy operation. A. Not enough water in footbath
basin. A. Fill basin 3″(7.6 cm) over top of suction cover.
B. Band straps (if applicable) on the
pump are not cut. B. Cut band straps.
7. Remote control (not
included) does not work. A. Remote not programmed. A. Re-program remote following instructions.
1032110-5-D 8 Kohler Co.

Service Parts
94821
O-Ring
94821
O-Ring
92076
Adapter
73518
Plug
93685
Housing
65886
Gasket
A
CORNER
96708
Flange
65054**
Screw
1003065
Suction Cover
65226**
Suction Plug
1032112
Heater Subassembly
1080774
Union Assy
1080774
Union Assy
1011398**
65061**
Suction Flange
Removal Tool
(Colored Finishes)
(Metal Finishes)
**Finish/color code must be specified when ordering.
Kohler Co. 9 1032110-5-D

94821
O-Ring
1003065
92076
Adapter
73518
Plug
93685
Housing
96708
Flange
65226**
Suction Plug
65054**
Screw
65886
Gasket
ALCOVE
Suction Cover
1032123 (K-1035-H2)
Harness Subassembly
(K-1036-H2)1032131
Harness Subassembly
A
94821
O-Ring
1080774
Union Assy 10109719
Connector
1012855
Nut
Suction Flange
Removal Tool
1011398**
65061**
(Colored Finishes)
(Metal Finishes)
**Finish/color code must be specified when ordering.
1032110-5-D 10 Kohler Co.

1033675
Heater 1032545
94821
O-Ring
94821
O-Ring
1012653
Adapter
1012653
Adapter
1012916
Nut w/Screws
90154
Nut
1018661
Control
1019447-A
Isolation Mount
61845-K
Copper Grounding Wire
(1-1/4"/3.2 cm)
1018964
Bracket
1019432
Carriage Bolt
90153
Locknut
65157
Nut
1020677
Gasket
1013469**
Trim Ring
1020679-C
1013460
Housing
94110
O-Ring
59588
Setscrew
1013459-C
Decal
See below for
cover/circuit
board detail.
Cover/Circuit Board
(2-1/4"/5.7 cm)
1019445-M
Stud
1019445-F
Spacer
1019444-F
**Finish/color code must be specified when ordering.
1010675
O-Ring
1010677
Screw
1010548
Volute
1010673
Seal
1016960
Impeller
1016958
Motor
1010676
Cover
1016957
Pump
1022495
Pump Nut Wrench
Housing
1015008
Plug/Wire Assembly
93893
Cover
60320
Screw
93892-A
Electrical Box 67065
Ground Lug
1033678
Screw
93003
Strain Relief
61776
Lock Washer
Kohler Co. 11 1032110-5-D

95031
Box
69307
Screw
93448
Plate
93458
Screw
Washer
Washer
69472
65218
60980
O-Ring
94821
O-Ring
B
A
96921
Bulkhead
93448
Plate
93458
Screw
69472
Washer
65218
Washer
TOWER
MOUNTING
HARDWARE
**Finish/color code must be specified when ordering.
1032110-5-D 12 Kohler Co.

67944-A
Nut
94160
Gasket
94143
Jet Spacer
94110
O-Ring
94308
Screw
B
94853
Tube
67944-B
Coupling
96978**
Jet Kit
96956
Butterfly
96976**
Fascia
96975
Jet Hood
96977**
Jet Kit
91828
Seal
93450**
End Cap
91828
Seal
93456
Screw
94290**
Handle
22325
Spline Insert
73598
Screw
94204
Bracket
94203
Stem 50506
Screw
50506
Screw
93839
Tube
60545
Reducer
95193
Screw
95194
Washer
94883
Gasket
See 96978** below.
**Finish/color code must be specified when ordering.
94078**
Flange
93434
Pin Hinge
93450**
End Cap
93456
Screw
TOWER
94160
Gasket
94143
Jet Spacer
94110
O-Ring
94308
Screw
Kohler Co. 13 1032110-5-D

1023091**
Cap
1013471**
Stand
1013464-B
Decal
1022253-B**
Remote
1013822-B**
Remote w/Stand
93836
93838
93839
94853
Tube (w/Couplings)
(1/2")
(1")
(1-1/2")
(1-1/4")
**Finish/color code must be specified when ordering.
1032110-5-D 14 Kohler Co.

94362
Wrench
62728
Allen Wrench
94749
Balldriver
1015694**
Seal
1015695**
Common Jamb
91225-D
Screw
94334**
Jamb
96882**
Handle
94823-B
Screw
92363-A**
Screw
94350**
Bumper
94367**
Clamp
94678**
Cap
94351
Gasket
91223-A**
Screw
92364-C**
Screw
94577**
Left Wall Jamb
94356**
94330-L**
94369-L**
91225-B
Screw
94822-A
Screw
94567**
Support
92363-A**
Screw
96886
Socket
See next page for
center panels and
header detail.
Right Hand Side Panel
(Includes 94343-B
Wiper)
Left Hand Side
Panel (Includes
94343-BWiper)
Right Wall
Jamb
**Finish/color code must be specified when ordering.
Corner Enclosure
94343-B
Wiper
94343-B
Wiper
Kohler Co. 15 1032110-5-D

96919**
Deflector
52557
Screw
94295**
Header
95035**
Deflector
96918**
Frame
90554
Nut
94825**
Back Stop
95048
Screw
94826**
Cap
95032**
Guide
94305-L**
Panel
96877-L**
Panel
94306-L**
Panel
95035**
Deflector
95023
Deflector
95023
Deflector
95033**
Guide
95033**
Guide
96918**
Frame
96918**
Frame
96918**
Frame
94711**
Stop
52557
Screw
94296
Bracket
64212
Washer
94822-A
Screw
94343-A
Wiper
Center Panels and Header
95032**
Guide
94354
Roller
1018808
Screw
94347
Bushing
1016436
Roller Screw Kit
94347
Bushing
**Finish/color code must be specified when ordering.
Corner Enclosure
1032110-5-D 16 Kohler Co.

1015694**
Seal
94337**
Jamb
92364-B**
Screw
94822-B
Screw
94822-C
Screw
94822-A
Screw
94552**
Expander
1015695**
Common Jamb
91225-D
Screw
94365**
Jamb
94350**
Bumper
94367**
Clamp
94678**
Cap
94351
Gasket
94362
Wrench
62728
Allen Wrench
94749
Balldriver
92364-C**
Screw
92363-A**
Screw
92363-A**
Screw
96882**
Handle
94822-C
Screw
92364-B**
Screw
96886
Socket
See next page for
center panels and
header detail.
94823-B
Screw
**Finish/color code must be specified when ordering.
Alcove Enclosure
Kohler Co. 17 1032110-5-D

96919**
Deflector
52557
Screw
94295**
Header
94354
Roller
95035**
Deflector
96918**
Frame
90554
Nut
94825**
Back stop
95048
Screw
94826**
Cap
95032**
Guide
95033**
Guide
94305-L**
Panel
94304-L**
Panel
94306-L**
Panel
95035**
Deflector
95033**
Guide
96918**
Frame
96918**
Frame
96918**
Frame
1018808
Screw
94347
Bushing
1016436
Roller Screw Kit
94711**
Stop
52557
Screw
94296
Bracket
64212
Washer
94822-A
Screw
94343-A
Wiper
94347
Bushing
Center Panels and Header
Alcove Enclosure
95032**
Guide
**Finish/color code must be specified when ordering.
1032110-5-D 18 Kohler Co.

Guide du propriétaire
Système d’hydromassage personnel à 8 jets
Informations importantes
INSTRUCTIONS RELATIVES AUX RISQUES
D’INCENDIE, D’ÉLECTROCUTION OU DE
BLESSURES CORPORELLES
LIRE ET SUIVRE TOUTES LES INSTRUCTIONS
CONSERVER CES INSTRUCTIONS
AVERTISSEMENT : Lors de l’utilisation des produits électriques, des précautions de base
devraient toujours être observées, incluant ce qui suit:
DANGER : Risque de blessures corporelles. Afin de réduire les risques de blessures, ne jamais
permettre à un enfant d’utiliser cet appareil sans surveillance.
AVERTISSEMENT : Risque de blessures corporelles. Pour éviter les blessures corporelles, entrer et
sortir de l’unité avec précaution.
AVERTISSEMENT : Risque d’électrocution. Ne pas raccorder des appareils électriques (tels que
sèche-cheveux, lampes, téléphones, radios ou télévisions) à une trop courte distance.
AVERTISSEMENT : Risque d’hyperthermie. Les personnes sous médicaments ou qui sont en
observation médicale doivent consulter leur médecin avant d’utiliser cet appareil.
Utiliser ce produit uniquement pour l’usage pour lequel il a été prévu tel que décrit dans ce manuel. Ne pas
utiliser des fixations non recommandées par le fabricant.
Ne jamais faire tomber ou insérer d’objet quelconque dans les ouvertures. Ne pas laisser de petits objets ou
des jouets pour le bain dans la baignoire à hydromassage lorsque celle-ci est en marche.
Ne pas utiliser cet appareil sans ses protecteurs (couvercles) sur ses raccords d’aspiration.
L’installation électrique doit avoir deux Disjoncteurs de Fuite de Terre (GFCI) ou des appareils de courant
résiduel (RCDs). Les GFCI ou les RCD protègent contre une électrocution par la mise à la terre. Utiliser deux
alimentations dédiées de 220240 V, 20 A, 50/60 Hz; une pour les pompes et les contrôles, et l’autre pour le
chauffe-eau. De tels disjoncteurs GFCI ou RCD devraient être fournis par l’installateur et vérifiés
régulièrement.
Appuyer sur le bouton de test pour tester les disjoncteurs GFCI ou RCD. Le GFCI ou RCD devraient couper
le courant. Appuyer sur le bouton de ré-initialisation. L’alimentation devrait être restituée.
Si les disjoncteurs GFCI or RCD ne fonctionnent pas de cette façon, l’un ou l’autre est défectueux. Si les
disjoncteurs GFCI ou RCD stoppent l’alimentation électrique à la baignoire sans que le bouton test ne soit
utilisé, il y a donc un court circuit.indiquant la possibilité de choc électrique. Ne pas utiliser.
Débranchez l’unité et la-faire vérifier par un Technicien Qualifié avant de l’utiliser.
AVERTISSEMENT : La consommation d’alcool, de drogues ou de médicaments peuvent
augmenter considérablement le risque fatal d’hyperthermie. Une immersion prolongée dans l’eau
chaude peut provoquer l’hyperthermie. L’hyperthermie a lieu lorsque la température corporelle
interne atteint plusieurs degrés au dessus de la temperature normale de 98,6°F (37°C). Les
symptômes d’hyperthermie comprennent la hausse de la température corporelle, l’étourdissement,
Kohler Co. Français-1 1032110-5-D

Informations importantes (cont.)
la léthargie, la somnolence et l’évanouissement. Les effets de l’hyperthermie comprennent: (a)
défaut de percevoir la chaleur, (b) défaut de s’apercevoir du besoin de sortir de la baignoire, (c)
incapacité de reconnaître le danger, (d) dommages au foetus dans le cas des femmes enceintes, (e)
incapacité physique de sortir de la baignoire et (f) inconscience et danger conséquent de noyade.
IMPORTANT ! Purger le système deux fois par mois ou plus souvent, selon la fréquence d’usage, tel que
décrit dans la section ″Entretien et nettoyage″.
Ne pas laisser la température d’eau dans le produit excéder 104°F (40°C).
Ne pas utiliser de savon, de shampooing ou de produit moussant pour le bain dans l’eau. Il vous est
possible d’employer du savon ou du shampooing pendant la douche, avant de remplir le receveur.
Votre nouveau produit a été homologué par l’ULC, ce qui assure par conséquent votre sécurité et celle de
votre famille. Cette nouvelle unité est conforme aux normes ANSI et aux normes IAPMO établies pour
l’industrie de la plomberie.
Merci d’avoir choisi la compagnie Kohler
Merci d’avoir choisi la compagnie Kohler. Votre produit de la compagnie Kohler reflète la véritable passion
du design, d’artisanat, d’art et d’innovation représentant la compagnie Kohler. Nous sommes confiants que
sa fiabilité et beauté surpasseront vos exigences les plus élevées, vous satisfaisant pendant les années à venir.
Toute information contenue dans ce guide est basée sur l’information la plus récente du produit disponible
au moment de la publication. A la compagnie Kohler, nous aspirons à remplir notre mission d’améliorer le
niveau de vie gracieux pour chaque individu affecté par nos produits et services. Nous nous réservons le
droit d’apporter des modifications aux caractéristiques, aux emballages et à la disponibilité des produits à
tout moment, et ce sans préavis.
Veuillez prendre s’il vous plaît quelques minutes pour étudier ce guide. Prêter une attention toute
particulière aux instructions d’entretien et de nettoyage.
1032110-5-D Français-2 Kohler Co.