Kohler K-1111-VLN-0 User manual

BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
Do not lift
the whirlpool by the piping or pump, or use the
piping or pump for structural support of the
whirlpool.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
CAUTION: Risk of product damage.
please leave these
instructions for the consumer.
·
·
We recommend this whirlpool for corner, drop-in, or
flush installations. An undermount kit is also
available.
Inspect the whirlpool for damage before you begin
installation.
You must install this whirlpool to an adequately
supported, level subfloor.
Confirm adequate support for a rim-mounted faucet,
if used; large faucets that may be inadvertently used
as a means of support are not appropriate or safe
for this installation.
Consult local and national codes.
Kohler Co. reserves the right to make revisions in
the design of products without notice, as specified in
the Price Book.
1036303-T01-A
INSTALLATION INSTRUCTIONS
WHIRLPOOL
K-1111-VLN
1
ã, 2011
Copyright Kohler China Ltd., 2011
C
1141609-T01-A

2
IMPORTANT INFORMATIONIMPORTANT INFORMATION
(GFCI) (ELCB)
WARNING: When using electrical products,
basic precautions should always be followed,
including the following:
DANGER: Risk of electric shock.
WARNING: Risk of electric shock.
WARNING: Risk of electric shock.
WARNING: Risk of injury or property damage.
Connect only
to circuits protected by Ground-Fault Circuit-
Interrupters (GFCI s) or Earth-Leakage Circuit-
Breakers (ELCB s).
A licensed
electrician should make all electrical connections.
Disconnect
power before servicing.
Please read all instructions thoroughly before
beginning installation, including the following
requirements.
'
'
·
·
·
·
·
·Building materials and wiring should be routed away
from the pump bodies and other heat-producing
components of the unit.
Install to permit access for servicing.
Pressure wire connectors marked Earth/Ground
are provided within the wiring compartments. To
reduce the risk of electric shock, connect these
connectors to the grounding terminals of your
electric service or supply panel with copper wire
equivalent in size to the circuit conductors supplying
this equipment.
Pressure wire connectors are provided on the
exterior of the junction boxes or controls within this
unit to permit connection of bonding conductors
between this unit and all other exposed metal in the
vicinity, as needed to comply with local
requirements.
The unit should be installed
by a qualified service representative, and grounded.
Grounding is required.
NOTICE: Follow all local plumbing and electrical
codes.
·
·
·
·
""
A.
2226
20 8 4
22 2
A. Features
Components include two pumps, two controls, two
heaters, 6 Flexjets, 20 Bodyssage backjets, 8
effervescence ports, 4 chromatherapy lights, 2 pillows,
and two illuminated keypads with two remote controls.
PRODUCT INFORMATIONPRODUCT INFORMATION
1141609-T01-A

3
B. Electrical Requirements
'
'''
The installation must have two Class A Ground-Fault
Circuit-Interrupters (GFCI s) or Earth-Leakage Circuit-
Breakers (ELCB s). The GFCI s or ELCB s protect
against line-to-ground shock hazard.
Do not relocate
the whirlpool pumps, or make other modifications
to the whirlpool system, as this could adversely
affect the performance and safe operation of the
whirlpool. Kohler Co. shall not be liable under its
warranty or otherwise for personal injury or
damage caused by any such unauthorized
modification.
Use two 220-240
V, 20 A, 50/60 Hz dedicated services; one for each
pump/control/heater system.
WARNING: Unauthorized modification may
cause unsafe operation and poor
performance of the whirlpool.
Product Notices
B.
A (GFCI)
(ELCB) GFCI ELCB
2 220/240 20 50/60
//
C. Connections and Service Access
Before installation, ensure proper access to the final
connections.
You must provide a minimum of
three 864mm wide x 381mm high access panels for
servicing the pumps and controls. The access must be
located immediately next to the pumps. Study the
roughing-in information packed with the whirlpool.
NOTICE: Provide generous, unrestricted service
access to the pumps.
C.
3
864mm 381mm
TOOLS AND MATERIALSTOOLS AND MATERIALS
Plus:
·
·
·
·
·
·
·
·
Conventional woodworking tools and materials
Drop Cloth
Cement, mortar or construction adhesive
2x4 wood boards
2x4
Silicone Sealant Measuring Tape Pencil Tin Snips
Safety Glasses Pipe Wrench
Level
1141609-T01-A

4
·
·
·
·
·
·
·
·
·
·
1/16
(2 )
CAUTION: Risk of product damage.
NOTICE:
Do not
support the whirlpool by the rim.
Adequate floor support must be provided.
Consult the roughing-in sheet packed with your
whirlpool for specific floor loading requirements.
·
·
·
·
·
·
·
·
·
·
If you have not already done so, carefully remove
the protective tape from the whirlpool rim.
Apply mortar and tile to the wall, deck and surround
material as needed.
Apply a bead of sealant where the tile meets the
whirlpool surface.
Install the faucet trim according to the instructions
packed with the trim.
Make sure the flooring offers adequate support for
your whirlpool, and verify that the subfloor is flat and
level.
The whirlpool may be installed as next to the wall or
in an island installation. An island installation
requires a four side surround. In both instances,
make sure the deck is supported by brick or
concrete.
Install an access panel to allow the pump to be
serviced.
Construct brick or concrete supports.
Provide a 2mm gap between the whirlpool rim and
the concrete or brick framing. Frame the floor or
construct a frame for a raised installation in
accordance with the roughing-in information packed
with the whirlpool.
Position the plumbing according to the roughing-in
information packed. Cap the supplies, and check for
leaks.
PREPARE THE SITE - CONCRETE CONSTRUCTIONPREPARE THE SITE - CONCRETE CONSTRUCTION
Bath
Brick
Approved Tile
Backing
Install an access panel to
allow the pump to be serviced.
Whirlpool may be installed next
to the wall or as an island installation.
Approved Tile Backing
2mm
Tile
Typical
Access
Panel
Brick
Tile
1141609-T01-A

5
·
·
·
·
2x4
CAUTION: Risk of product damage.
NOTICE:
Do not
support the whirlpool by the rim.
Adequate floor support must be provided.
Consult the roughing-in sheet packed with your
whirlpool for specific floor loading requirements. Three
access panels are required.
·
·
·
·
Make sure the flooring offers adequate support for
your whirlpool, and verify that the subfloor is flat and
level.
The whirlpool should be installed as a corner, drop-
in, or flush installation. Construct 2x4 stud framing
designed for your particular installation. Frame the
floor, or construct a frame for a raised installation in
accordance with the roughing-in information packed
with the whirlpool.
Use the roughing-in cut-out information to carefully
lay out and cut the rough deck material. For flush-
mount installation, allow for the thickness of the
planned deck material.
Position the plumbing according to the roughing-in
information packed. Cap the supplies, and check for
leaks.
PREPARE THE SITE - WOOD CONSTRUCTIONPREPARE THE SITE - WOOD CONSTRUCTION
·
·
·
We recommend a tiling-in bead for straight-rimmed
whirlpools if one or more sides of the whirlpool
contact a wall. This bead prevents water from
seeping between the whirlpool rim and the wall.
Follow the instructions packed with the tiling-in bead
to install the bead now.
Install the drain to the whirlpool according to the
drain manufacturer s instructions. Do not connect
the trap at this time.
Position a clean drop cloth or similar material in the
bottom of the whirlpool. Be careful not to scratch the
surface of the whirlpool.
'
Whirlpool Rim Do not support the
whirlpool by the rim.
Use the roughing-in
information to construct
the stud framing.
Allow for the thickness of
the planned deck material.
Drop-In Installation
Whirlpool Rim
Wood Batten
Flush Installation
Access Panel 1
1
Seat Access Panel 3
3
Access Panel 2
2
PREPARE THE WHIRLPOOLPREPARE THE WHIRLPOOL
·
·
·
1141609-T01-A

CAUTION: Risk of product damage.
Choose the installation option that best applies
to your particular installation. Follow the
appropriate instructions.
Do not lift
the whirlpool by the piping or pumps, or use the
piping or pumps for structural support of the
whirlpool.
If the subfloor is not level, shim the whirlpool support
blocks as necessary.
·
·
!2 (50
)
!
!
Option for Using a Cement or Mortar Bed
!
!
!
2" (Spread a 50mm) thick layer of cement or mortar
on the subfloor where the whirlpool will be set.
This will help secure, level, and support the unit.
Clear all the material away from the pump controls
and support block locations.
Do not use gypsum cement or drywall
compound for this application, as they will not provide
an acceptable, durable bond.
Position a piece of plastic drop cloth material on top
of the cement or mortar bed. With help, carefully lift
the whirlpool into place, and make sure the pump
controls and support blocks do not rest in the bed
material.
Insert the drain tailpiece into the trap. Make sure the
whirlpool is level and resting on all support blocks.
NOTE:
NOTE: The pump controls (when the pump banding
straps are cut) and support blocks must rest
directly on the subfloor.
·
·
6
SECURE THE WHIRLPOOL TO THE SUBFLOORSECURE THE WHIRLPOOL TO THE SUBFLOOR
Option for Using Construction Adhesive
Apply a generous amount of high-quality
construction adhesive to the bottom of the support
blocks. With help, carefully lift the whirlpool into
position.
Insert the drain tailpiece into the trap. Make sure the
whirlpool is level and resting on all support blocks.
·
·
Option for Using Silicone Sealant
With help, carefully lift the whirlpool into position.
Insert the drain tailpiece into the trap. Make sure the
whirlpool is level and resting on all support blocks.
Apply a continuous bead of high-quality silicone
sealant around the entire rim of the whirlpool.
·
·
·
!
!
!
!
!
Apply construction adhesive
to the support blocks
Apply a bead of silicone
sealant around the entire rim
Or
Clear spaces for
support blocks
Clear space for pump.
Spread A 2" (51mm)
layer of cement or
mortar bed material.
2 (51 )
1141609-T01-A

CAUTION: Risk of property damage.
NOTICE:
NOTE:
Ensure a
watertight seal on the whirlpool drain.
Connect the drain to the trap according to the drain
manufacturer s instructions.
An access panel will simplify future
maintenance.
Check for the required clearance under the rim
of the bath before drilling the hole for the faucet.
Install the faucet valving according to the
manufacturer s instructions. Do not install the faucet
trim until instructed.
Open the hot and cold water supplies.
Check the supply connection for leakage.
Run water into the whirlpool, and check the drain
connections for leakage.
·
·
·
·
·
'
'
·
·
·
·
·
CUT THE PUMP BANDING STRAPSCUT THE PUMP BANDING STRAPS
IMPORTANT! This step is necessary to make your
Kohler whirlpool operate more quietly.
NOTE:
Use tin snips to cut the two pump banding straps
from each whirlpool pump.
Do not raise the pumps higher than they were
before you cut the pump banding straps. If the pumps
are raised too high, they will not prime properly. Make
sure the rubber isolation feet are in place.
To minimize whirlpool noise and vibration, be sure
the pumps are not in direct contact with the
whirlpool after the pump banding straps are cut. The
pump controls contain rubber isolation feet to
reduce pump noise.
·
·
·
·
Pump
Wiring Harness
Rubber Isolation Feet
Control
Cut the pump
banding straps
7
Junction Box
INSTALL THE PLUMBINGINSTALL THE PLUMBING
MAKE ELECTRICAL CONNECTIONSMAKE ELECTRICAL CONNECTIONS
NOTE:
WARNING: Risk of electrical shock.
The product model number is printed on a label
on the pump side of the whirlpool bath. This label also
identifies the electrical rating of the product. All
whirlpools come equipped with a wiring junction box
and are designed to operate between 208 VAC and
240 VAC at either 50 Hz or 60 Hz.
Make
sure the power has been disconnected before
performing the following procedures. Refer to the
"Important Information" section.
208~240 50 60
1141609-T01-A

8
WARNING: Risk of electrical shock.
IMPORTANT! load neutral
load neutral
equipment ground
To reduce
the risk of electrical shock, connect the pump to
a properly grounded Ground-Fault Circuit-
Interrupter (GFCI) or Earth-Leakage Circuit-
Breaker (ELCB). This will provide additional
protection against line-to-ground shock hazard. A
208-240 V, 20 A, 50/60 Hz dedicated circuit is
required.
The is not used. There
should be no connection to the terminal
on the Ground-Fault Circuit-Interrupter (GFCI) breaker.
The green wire with the yellow stripes is the
and needs to be connected to the
neutral bus in the main circuit breaker box.
(GFCI)
(ELCB)
208-240 20 50/60
(GFCI)
·
·
·
·
The whirlpool bath control and system have been
pre-wired at the factory. A licensed electrician should
make a routine service connection to the junction box.
Connect service to the junction box. The junction box
contains blue, brown, and green with a yellow stripe
colored wires.
Follow local electrical codes. Bond in accordance
with national and local codes.
A wiring harness has been pre-wired at the factory,
allowing communication between the keypad, all
features, and the control. No additional wiring is
required, but ensure that all wires are securely
fastened.
Your wiring harness included an antenna for the
optional remote control. Do not alter or damage this
antenna during installation.
NOTE:
·
·
·
·
120/240 VAC
Source
* Connections to be Made
at the Circuit Breaker
Field Wiring
(From Junction Box
to GFCI Breaker)
No Connection
(Load Neutral)
* Equipment Ground
Neutral Bus
(In Breaker Box)
* Line Neutral
(White Curly
Wire)
Typical Two-Pole
Circuit Breaker
with GFCI
Breaker Box
Heater (models may vary) T-style (shown)
or In-line (not shown)
()T()
()
Bond in accordance with national and local codes.
Open bonding lugs are located at the top of the
junction box.
Typical Wiring Connection for North America
Wire Connector
Ground (Green with
Yellow Stripes)
()
From Control
Brown (L2)
Wire Connectors
Electrician to provide suitable
strain relief cable.
Blue (L1)
S/N
240 V
120 V
120 V
NL1L2
*L2
240 V
*L1
Heater Electrical Cord
Pump Electrical Cord
Wiring Harness
Junction Box
Control
1141609-T01-A

9
INSTALL THE WHIRLPOOL TRIM KITINSTALL THE WHIRLPOOL TRIM KIT
·
·
·
·
Install the whirlpool trim kit according to the
instructions packed with the trim kit. Pay particular
attention to the jet installation steps below - they are
very important and are included here to help you
obtain smooth, trouble-free jet operation. When
installed correctly, the jet should turn smoothly both
clockwise and counterclockwise.
The jet O-ring must be carefully positioned,
lubricated, and be in good condition to permit easy
rotation and proper operation of the jet.
Lubricate the O-ring with silicone lubricant to
prevent noisy operation of the jet.
Install the O-ring onto of the jet.
Carefully insert the jet into the housing, and lightly
push and rotate the jet until it snaps into position.
NOTE:
the first shoulder
Do not force the jet into place.
·
·
·
·
O
O
O
Housing Slide the o-ring onto
the first shoulder of the jet
O
Inspect and lubricate
the o-ring
O
Insert the jet into the
housing, and lightly push
and rotate until it snaps
in position
TEST RUN THE WHIRLPOOLTEST RUN THE WHIRLPOOL
·
·
·
·
·
·
·
Check all electrical connections, then make sure all
union connections to the pumps and heaters are
securely hand tightened.
Verify both sets of pump banding straps have been
cut and the pump controls are resting directly on the
subfloor. Ensure the rubber isolation feet are in
place.
Turn electrical power to both pumps on.
Fill the whirlpool with water until the water level is
above the highest backjet.
Operate the whirlpool for 5 minutes (refer to the
"Operating Sequence" section). Three small lights
near the whirlpool floor will illuminate as long as the
keypad remains lit. The keypad controls the
chromatherapy feature.
Check for leaks coming from the piping connections
on the back side of the whirlpool unit.
Turn on the each of the whirlpool features and verify
proper function. Check for any water leakage on the
whirlpool's back side.
·
·
·
·
·
·
·
5( )
1141609-T01-A

·
·
Turn on the chromatherapy cycle and allow it to
sequence through all eight colors; white, violet,
indigo blue, aqua blue, green, yellow, orange and
red. It takes approximately 1 minute to cycle through
all eight colors.
Verify functions using the remote controls. Refer to
the Remote Control Operation section of this guide
and supplemental instruction sheet, Programming
Your Remote Controls , packed with your literature.
For additional information on whirlpool
operation, see the Confirm Proper Operation section
of this guide.
NOTE:
""
"
"
""
·
·
8
81
10
·
·
·
·
If you have not already done so, carefully remove
the protective tape from the whirlpool rim.
Cover the framing with water-resistant wall material.
Seal the joints between the whirlpool rim edge and
the water-resistant wall material with silicone sealant.
Tape and mud the water-resistant wall material.
Install the finished wall to the water-resistant wall
material so it is 2mm above the bath surface. Seal
the joints between the whirlpool rim and the finished
wall material with silicone sealant.
Install the faucet trim according to the instructions
packed with the trim.
·
·
·
·
/
/
/
/
//
2mm
COMPLETE THE FINISHED WALL/DECKCOMPLETE THE FINISHED WALL/DECK
Apply silicone sealant to the water-resistant
wall material and the finished wall.
Apply silicone sealant to the water-resistant
wall material and the finished wall.
Install the finished
wall material.
First install water-resistant
wall material.
Drop-In Installation
Install the finished wall
material.
First install water-resistant
wall material.
Flush Installation
Whirlpool
Whirlpool
1141609-T01-A

11
CLEAN-UP AFTER INSTALLATIONCLEAN-UP AFTER INSTALLATION
·
·
·
·
·
·
When cleaning up after installation, do not use
abrasive cleansers, as they may scratch and dull the
whirlpool surface. If necessary, use warm water and
a liquid detergent to clean the surface of the
whirlpool, user keypad and remote control.
Remove stubborn stains, paint, or tar with turpentine
or paint thinner.
Remove plaster by carefully scraping with a wood
edge. Do not use metal scrapers, wire brushes, or
other metal tools. Use a powder-type detergent on a
damp cloth to provide mild abrasive action to any
residual plaster.
Do not allow cleaners containing
petroleum distillates to remain in contact with
any whirlpool surfaces for long periods of time.
CAUTION: Risk of product damage.
NOTE:
Do not
submerge the pillows underwater or use them as
seat cushions.
For best attachment to the whirlpool surface,
moisten the back surface of the pillows at the suction
cup locations.
Clean the whirlpool surface of any soap film or oils.
Moisten the suction cups located on the back side of
the pillows. Position the small pillows above the
backjets and above the waterline by pressing down
firmly with the heel of your hand. Check to make
sure that the pillows are attached firmly to the
whirlpool.
Detach the pillows by lifting them off the whirlpool
surface.
·
·
INSTALL THE REMOVABLE PILLOWSINSTALL THE REMOVABLE PILLOWS
Position the small pillows as
desired above the waterline
and above the backjets.
1141609-T01-A

Fill the Whirlpool
NOTE:
NOTE:
Please read these steps carefully before you
operate your whirlpool.
Turn the jet trim rings fully counterclockwise.
Position the jet nozzles so they face down toward
the basin.
Fill the whirlpool with water until the water level is
above the highest backjet.
The water temperature in the whirlpool should
not exceed 104 F (40 C). The heater will automatically
turn off as the water temperature approaches 104 F
(40 C) and will remain off until the water cools.
oo
o
o
·
·
40 40
·
·
12
CONFIRM PROPER OPERATIONCONFIRM PROPER OPERATION
Your whirlpool is equipped with two keypads, each
controlled by its own operating system. Follow the
steps below to confirm the keypads are operating
correctly.
A built-in heater automatically helps to maintain
the water temperature when the whirlpool is running, as
long as the water temperature does not exceed 104 F
(40 C). The heater will disengage at higher
temperatures.
Please refer to your Homeowners Guide
for detailed instructions on the user keypad and remote
control.
The keypad controls the chromatherapy feature.
Press the Power On/Off button on the keypad to
turn the whirlpool on. The whirlpool will start at
medium flow and three small lights near the
whirlpool floor will illuminate as long as the keypad
remains lit.
Increase or decrease the water flow by pressing
either the up or down arrow buttons on the keypad.
An indicator bar in the center of the keypad shows
the water flow volume.
Adjust each Flexjet for optimum air/water mixture.
Turn the Flexjet trim clockwise to reduce the air flow
and counterclockwise to increase the airflow.
NOTE:
IMPORTANT!
NOTE:
o
o
·
·
·
Water-Level Sensors - To use all functions (including
backjets), fill to a level above both water-level sensors.
()
Flexjet - Turn the jet trim ring fully
counterclockwise and position the
jet nozzle downward.
Suction Cover
2
/
3
40 40
/
·
·
·
OPERATING SEQUENCEOPERATING SEQUENCE
1141609-T01-A

·Rotate the outer ring until the heater button is
flashing. Press OK to turn the heater off. Press
OK again to turn the heater back on. The heater
will help to maintain the water temperature up to
104 F (40 C).
Press the Power On/Off button a second time to turn
the whirlpool off. The lights near the whirlpool floor
will remain illuminated until the keypad enters the
sleep mode.
Repeat the steps above to verify the operation of the
second keypad.
A built-in timer automatically stops the pump
and motor after approximately 20 minutes of operation.
oo
NOTE:
""
""
·
·
·
·
·
OK OK
40
20
/
Flexjet Flow Mode
Increases Flow
or Pulse Rate
Effervescence Mode
Indicator Bar - Shows
water flow volume or
pulse rate
Chromatherapy Cycle
Decreases Flow
Heater On/Off
Power On/Off
Chromatherapy-
Specific Color
Rotate outer ring to
access desired mode.
Backjet Mode-
Adjust Pulse
Activates Mode
Selected
Lighted User Keypad
Turn the Flexjet
trim clockwise to
decrease the flow.
Turn the Flexjet trim
counterclockwise
to increase the flow.
Backjet Operation
NOTE:
Rotate the outer ring until the backjet mode is
flashing and press OK . The backjet pulsing action
will start at medium speed. The backjet pulsing
action will start at medium speed. The backjets
pulse from the bottom of the whirlpool toward the
top, with water flow and pulse action occuring
from two backjets at a time.
If the water level falls below the water level
sensors, the backjets will stop. The backjet icon and
indicator bar on the user keypad will flash. The backjets
will automatically restart when the water level covers
the sensors.
·
""
·To increase or decrease the backjet pulsing action,
press either the up or down arrow buttons on the
keypad, while the backjet mode is active.
To increase or decrease the flow volume to the
backjets, rotate the outer ring to the Flexjet mode,
press OK to activate the mode, and press either
the up or down arrows on the keypad. This also
increases or decreases the flow to all modes.
To activate or deactivate different modes while
the backjets are operating, rotate the outer ring until the
disired mode is flashing and press OK . (Example: To
turn the heater off, rotate the ring until the heater icon is
flashing and press OK ).
Press OK while the backjet mode is flashing to
turn off the backjets.
Repeat the above steps for the second keypad.
NOTE:
·
·
·
""
""
""
""
OK·
·
·
·
·
OK
OK
(
OK )
OK
MODES OF OPERATIONMODES OF OPERATION
13
1141609-T01-A

14
Effervescence Operation
NOTE:
·
·
·
·
·
With the whirlpool operating, rotate the outer ring of
the keypad until the effervescence icon is flashing.
Press OK to activate the effervescence ports. The
effervescence action will start at the flow volume last
set in the flexjet flow mode.
Increase or decrease the flow volume by pressing
either the up or down arrow buttons on the keypad.
The effervescence mode is intended to be a
relaxing, soothing experience. The Flexjet mode and
backjets will automatically turn off when the
effervescence mode is activated. Chromatherapy may
be used with all modes of operation.
Press OK while the effervescence mode is flashing
to turn off the effervescence ports.
Repeat the above steps for the second keypad.
""
""
Chromatherapy Operation
NOTE:
Chromatherapy Cycle.
Chromatherapy Specific Color Selection.
Chromatherapy may be used with all modes of
operation or when the pump is not operating.
When the pump is not operating, only one of the
keypads will control the chromatherapy operation.
When this mode is
activated, the chromatherapy lights will
automatically and continuously cycle through the
eight colors; white, violet, indigo blue, aqua blue,
green, yellow, orange, and red. One cycle through
all eight colors takes approximately one minute.
Rotate the outer ring to select this mode and press
OK to activate it. Press OK while the
chromatherapy mode is active to end the cycle.
When
this mode is activated, you may choose a specific
color for the bath. Rotate the outer ring to select this
mode and press OK to activate it. Use the
up/down arrows to reach the desired color. Press
OK while the chromatherapy mode is active to end
the Chromatherapy operation.
·
·
"" ""
""
""
·
·
·
·
·
OK
OK
·
·
8
81
OK
OK
OK
OK
NOTE: Refer to your Homeowners Guide for detailed
instructions on your remote control.
Because your unit has two keypads and two remote
controls, you must program both remote controls.
For detailed instructions, refer to the supplemental
instruction sheet, Programming Your Remote
Controls , packed with your literature.
The remote control places the whirlpool functions at
your fingertips. You may access and modify all
modes/features from the remote control. The
waterproof remote control is designed to be used in
the bath and will float in the water. The remote
control uses two AAA batteries.
The mode selector button functions in the same way
as the outer ring. When M is pressed, one of the
modes will flash on the user keypad. If M is
pressed again, the next mode in clockwise order will
flash. When the desired mode is flashing, press
OK to activate it.
·
·
·
"
"
""
""
""
2
M
M
OK
·
·
·
AAA
REMOTE CONTROL OPERATIONREMOTE CONTROL OPERATION
1141609-T01-A

·When the Flexjet mode is active, the arrows will
increase or decrease the water flow volume. When
the backjet mode is active, the arrows increase or
decrease the backjet pulse speed.
·
SYMPTOMS
A. Check wiring and connect power.
B. Reset GFCI or ELCB.
C. Check wiring for proper connections.
Replace wiring harness if necessary.
D. Replace user keypad.
E. Replace control.
A. Rotate jet trim counterclockwise to open.
B. Reinstall jet; check for O-ring damage.
C. Remove blockage.
A. Reset GFCI or ELCB.
B. Check wiring for proper connections.
Replace wiring harness if necessary.
C. Replace user keypad.
D. Replace control.
A. Reset GFCI or ELCB.
B. Check wiring for proper connections.
Replace wiring harness if necessary.
C. Replace user keypad.
D. Replace control.
A. Check wiring for proper connections.
B. Replace pump.
C. Replace control.
A. Lower pump/control to subfloor level.
B. Securely tighten nut(s) on intake side of
pump.
C. Replace motor/pump.
D. Replace control.
A. Identify source of fault and correct. Reset
GFCI or ELCB.
B. Remove obstruction.
C. Remove blockage.
D. Check for blockage at suction and/or jets.
Remove blockage and allow motor to cool.
A. See service manual.
A. Replace user keypad.
B. Replace control.
PROBABLE CAUSES RECOMMENDED ACTION
1. User keypad does
not illuminate when
power button is
pressed or outer ring
is rotated.
2. Motor starts, but all
jets are not
functioning.
3. User keypad is
illuminated, but does
not respond to
buttons or outer ring.
4. User keypad
indicator bar keeps
scanning at power-up.
5. User keypad is
illuminated, but pump
won't start.
6. Motor runs but pump
won't prime
(cavitates).
7. Pump stops before
18 minutes.
8. Pump does not
automatically stop
after 22 minutes.
9. Pump will not turn off
when the power
button on the user
keypad is pressed.
A. No power to control.
B. GFCI or ELCB tripped.
C. Wiring harness from user keypad to
control is loose, disconnected or
damaged.
D. User keypad does not work.
E. Control does not work.
A. Jet is closed.
B. Jet not installed correctly.
C. Jets are blocked.
A. Control program is locked.
B. Wiring harness from user keypad to
control is loose, disconnected or
damaged.
C. User keypad does not work.
D. Control does not work.
A. Control program is locked.
B. Wiring harness from user keypad to
control is loose, disconnected or
damaged.
C. User keypad does not work.
D. Control does not work.
A. Power cord from pump to control is loose,
disconnected or damaged.
B. Pump does not work.
C. Control does not work.
A. Pump is shimmed too high.
B. Small air leak at pump inlet.
C. Motor/pump does not work.
D. Control does not work.
A. GFCI or ELCB tripped.
B. Suction is blocked
C. Jets are blocked.
D. Motor overheated and protection device
activated.
A. 20-minute timer inadvertently disabled.
A. User keypad does not work.
B. Control does not work.
This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualified electrician
should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor.
Troubleshooting the Whirlpool System
TROUBLESHOOTING PROCEDURESTROUBLESHOOTING PROCEDURES
15
1141609-T01-A

A.
B. GFCI ELCB
C.
D.
E.
1. A.
B. GFCI ELCB
C.
D.
E.
A.
B. O
C.
A. GFCI ELCB
B.
C.
D.
2.
3.
A.
B.
C.
A.
B.
C.
D.
A. GFCI ELCB
B.
C.
D.
4. A.
B.
C.
D.
A.
B.
C.
A. /
B.
C. /
D.
5.
6.
A.
B.
C.
A.
B.
C. /
D.
A. GFCI
ELCB
B.
C.
D. /
A.
7. 18
8. 22
A. GFCI ELCB
B.
C.
D.
A. 20
A.
B.
9. A.
B.
16
1141609-T01-A

SYMPTOMS
A. Replace motor/pump.
B. Replace control.
PROBABLE CAUSES
10.Pump operates but
variable speed
feature does not
work.
A. Motor/pump does not work.
B. Control does not work.
A. Allow bath water to cool.
B. Turn heater on.
C. Check wiring for proper connections.
D. Replace heater.
E. Replace control.
11.Bath water cools
while pump is
operating.
A. oo Water temperature above 104 F (40 C).
B. Heater is turned off on user keypad.
C. Wiring from heater to control is loose,
disconnected, or damaged.
D. Heater does not work.
E. Control does not work.
A. Cut pump banding straps with tin snips.
B. Remove jet, replace and lubricate O-ring,
then reinstall jet.
12.Noisy operation. A. Pump banding straps have not been cut.
B. Dry or dislodged jet O-ring (squeal).
A. Replace batteries.
B. Replace wiring harness.
C. See homeowners guide or service manual.
D. Replace remote control.
E. Replace control.
A. Check for loose or damaged wires.
Repair or replace as needed.
13.Remote control does
not work or operates
both pumps.
14.Lights near whirlpool
floor do not
illuminate.
A. Batteries improperly installed or dead.
B. Antenna on wiring harness is damaged.
C. Remote control not programmed correctly.
D. Remote control does not work.
E. Control does not work.
A. Wiring damage.
Troubleshooting continued
A. /
B.
10. A. /
B.
A.
B.
C.
D.
E.
11. A. 40
B.
C.
D.
E.
A.
B. O
12. A.
B. O ( )
A.
B.
C.
D.
E.
A.
13.
14.
A.
B.
C.
D.
E.
A.
17
RECOMMENDED ACTION
1141609-T01-A

SYMPTOMS
A. Turn on pump.
B. Check for loose connections or wires
leading from backjet pulse canister to
control. Replace backjet pulse canister or
control if necessary.
C. Fill whirlpool so water level sensors are
covered.
D. Replace actuator switch.
E. Check for loose connections or wires
leading from the pump motor to the control.
F. Remove blockage.
G. Reconnect or replace switch wires that
use modular plug.
PROBABLE CAUSES
15.Backjets do not
operate.
A. Whirlpool pump is not operating.
B. Backjet butterfly valve does not open.
C. Not enough water in whirlpool.
D. Actuator switch does not work.
E. Power from pump motor to control is off.
F. Backjet pipe is blocked.
G. Switch wire from switch to control is
disconnected.
A. Check for loose connections or wires
leading from pulse canister to control.
Replace pulse canister or control if
necessary.
B. Replace switch.
C. Reconnect or replace switch wires that
use modular plug.
16.Backjets do not
pulse.
A. Pulse canister does not work.
B. Switch does not work.
C. Switch wire from switch to control is
disconnected.
Troubleshooting the Beckjet Syetem
A.
B.
C.
D.
E.
F.
G.
15. A.
B.
C.
D.
E.
F.
G.
A.
B.
C.
16. A.
B.
C.
18
RECOMMENDED ACTION
1141609-T01-A

SYMPTOMS
A. Turn on pump.
B. Replace butterfly valve.
C. Refer to the service manual to
troubleshoot the system. Refer to
installer/dealer.
D. Replace control.
PROBABLE CAUSES
17.Effervescence ports
do not work.
A. Whirlpool pump is not operating.
B. Effervescence butterfly valve does not
work.
C. Pump does not work.
D. Control does not work.
A. Remove blockage.
B. Increase water flow.
18.Effervescence ports
do not bubble.
A. Air intake on suction line is blocked.
B. Water flow is too low.
Troubleshooting the Effervescence Jets
A.
B.
C.
/
D.
17. A.
B.
C.
D.
A.
B.
18. A.
B.
SYMPTOMS
A. Check wiring for proper connections.
Replace wiring if necessary.
B. Replace control.
PROBABLE CAUSES
19.Chromatherapy
lights do not work.
A. Loose, disconnected or damaged
wiring/connections.
B. Control does not work.
Troubleshooting the Chromatherapy Lights - H2 Models Only
A.
B.
19. A.
B.
H2
19
RECOMMENDED ACTION
RECOMMENDED ACTION
1141609-T01-A