Kohler 11829T-B User manual

1240256-2A-A 1
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
11829T-B Shower Column
HANDLE OPERATION
Turn the diverter handle counter-clockwise, the back connector of the diverter works; turn it clockwise, showerhead
works.
ROUGH-IN DIMENSIONS
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Shut off the water supplies to the fitting.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. Recommended minimum working pressures is 0.2~0.5MPa(2~5bar).
5. This faucet must work with a valve system (purchased separately) which has both on/off and hot/cold controls.
6. The highest working pressure for showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer
is needed. The highest water and environment temperature is 60°C. Please keep handspray, showerhead and the
shower arm away from heater, or it may become damaged and cause injury to the user.
G1/2˝
G1/2˝
500
34
700~800
422
1063
1158
332
900~1000
G1/2˝
G1/2˝
Floor
Ø182
(68~79)
Wall

1240256-2A-A 2 1240256-2A-A 3
INSTALLATION
How To Install The Shower Column
Select a location in vertical wall to install shower column according to
rough-in dimensions.
Drill the lower hole as anchors(1) diameter and lower base(3-1) position
in the finished wall(NOTE: The arrow in the base is upward). Press
anchors into the hole, secure the base by the screw(2).
Rehearse the slide bar kit(4) installation for the upper base(3-2) mounting
location determination. Slide the tube joint(5) onto the slide bar kit, and
connect them to the base(NOTE: The arrow in the base is upward).
Install the screws(7) into the tube joint with the hex wrench(6), and
tighten them.
Place the slide bar and the body against the finished wall. Connect the
lower base and the diverter body kit(8). Position and tighten them by hex
wrench. Mark the hole of upper base(3-2) with a pencil. Uninstall the slide
bar kit and tube joint.(NOTE: Don’t lose the screws.)
Drill holes on the mark. Press the anchors into the holes. Secure the
upper base(3-2) by the screws. Install the tube joint(5) to the base(3-2)
and tighten them by screws. Reinstall the slide bar kit with escutcheons
(9) to the bases. Tighten the screws with the hex wrench. Screw the
escutcheons with the bases until against the finished wall.
Connect the hose(10) with washers(11) between the mixer water supply
and the connector(12). The connector(13) will be used for handspray
connection.
11829T-B Shower Column
SERVICE PARTS
**Color code must be specified when ordering
How To Install The Showerhead
T urn the diverter handle to showerhead(14) work, run hot and cold water
for about one minute to remove any debris before the showerhead is
installed.
Before installation, put the regulator(15) into the showerhead inlet if
needed. Take out the washer(16) and install the regulator as shown,
reinstall the washer.
Tighten the showerhead onto the tube kit outlet(17)
with strap wrench.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
12
7
3-2
9
1
2
7
3-1
9
8
13 12
5
6
4
10
11
11
15
14
16
17
1196610
1196607**
832751
832751
1061576
1196621**
1196628
1183267**
1046290
870921
870921
1111667**
880010
832751
1196622** 1157203
1196610
1196624**
1061576
1196621**
1200829**
1109471**
77420
1066008**
1030624
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight. Close the valves.
Turn on the main water supply, and check for leaks. Repair as needed.