Kohler K-2276 User manual

Fig. #1
9”
(22.9cm)
MIN.
27”
(68.6cm)
MIN.
8”
(20.3cm)
MIN. 6”
(15.2cm)
MAX.
ADA CLEARANCE, SELF-RIMMING ONLY
3-1/2”
(8.9cm)
34”
(86.4cm)
24” (61cm)
***10”
(25.4cm)
(T)
3/8” COLD
1-1/4” OUTLET
(S)
C
L OF FITTING*
3/8” HOT
ADA DRAIN OUTLET ***10”
(25.4cm)
17-1/2” (44.5cm) D.
10-3/4”
(27.3cm)
1-1/4” (3.2cm)
**3”
(7.6cm) 6”
(15.2cm)
4” (10.2cm)
1-1/2”
(3.8cm)
4” (10.2cm)
1010430-2-AEspañol, Página 9
Français, Page 17

SPUN GLASSVESSELS
SELF-RIMMING AND
ABOVE-COUNTER LAVATORIES
K-2276
BEFORE YOU BEGIN
NOTES
Use these instructions for both self-rimming, and
above-counter installations. Follow only the
instructions that apply to your installation.
This lavatory gives you the opportunity to be
creative and flexible with the installation.
You can choose between a wall-mount or
countertop faucet installation, depending upon the
setting and styling you desire. We recommend a
wall-mount faucet.
Prior to installation, unpack the new lavatory and
carefully inspect it for damage. Return the lavatory
to its protective carton until you are ready to install
it.
During installation, store the lavatory in the
protective carton whenever possible.
Never stand or store the lavatory on the drain
surface.
To ease forming of the supplied adhesive seal,
install this lavatory when the temperature is
between 70°F (21°C) and 100°F (37°C).
These instructions contain important care, cleaning,
and warranty information - please leave these
instructions for the consumer.
TOOLS AND MATERIALS REQUIRED
Safety glasses
Safety shoes
Pencil
Scissors
Tape measure
Putty knife
Hole saw
Keyhole saw or saber saw
Drill (1/2” dia. drill bit or larger)
Clear silicone sealant (optional)
50/50 mix of isopropyl alcohol and water
Waterproof sealer (for porous countertops)
PRODUCT INFORMATION
Approximate weight 18 lbs. (8 Kg.). . . . . . . . . . . . . .
CAUTION: Risk of personal injury or product
damage. This lavatory is made of glass. Always use
the same extreme care appropriate for fine china
when handling to avoid breakage.
ROUGHING-INDIMENSIONS
Roughing-In Notes
( T ) Pop-up drain 9” (22.9cm).
( S ) 14” (35.6cm) (Based on 12” (30.5cm) riser which may require
cutting.)
* Spout must be 5” (12.7cm) long (min.) for adequate clearance
into lavatory when installed with centerline as shown.
** Spout must be tall enough to clear 3” (7.6cm) rim height and
provide a 1” (2.5cm) air gap per ASME A112.1.2.
*** Based on K-9018, with 1” (2.5cm) of tailpiece exposed.

2
1010430-2-AKohler Co., Kohler, WI U.S.A.
SELF-RIMMING INSTALLATION
Determine the faucet centerline location. Consider the
faucet and handle escutcheon diameters, the length of
the spout, and the clearance between the spout and the
lavatory rim.
Calculate the faucet centerline measurement by first
dividing the escutcheon diameter in half, and then add
1/4” (6mm).
NOTE: Round this calculation up to the nearest 1/16”
(2mm), if necessary. Fig. #2
Faucet
Centerline
Divide Escutcheon
Diameter in Half, Then
Add 1/4” (6mm)
       
       
     
compliance with all state and local plumbing codes;
a minimum 2” (5cm) distance from the water stream
to the lavatory rim edge. This is important to ensure
adequate clearance for hand washing (refer to
Fig. #3);
a minimum 1/4” (6mm) distance between the faucet
spout and the lavatory rim (refer to Fig. #4).
Redraw the faucet centerline as needed to meet these
criteria. Be sure to use the template line labeled “Rim of
Lavatory”.
Fig. #3
Fig. #4
2” (5cm) Min.
1/4” (6mm) Min.
Air Gap
2” (5cm) Min.
           
        
   
NOTE:        
     
Cut along the backsplash locator line on the template.
Fig. #5
Countertop
Backsplash Backsplash
Locator Line
Countertop
Faucet Centerline2” (5cm) Min.
Cut-Out Template

31010430-2-A
Kohler Co., Kohler, WI U.S.A.
Turn off the water supply to the faucet.
Open the faucet valves to relieve water pressure, then
disconnect the supply lines.
Disconnect the drain assembly, and remove the trap.
Remove the existing lavatory.
Fig. #6
Faucet
Drain Assembly
Supply Lines
Shut-Off valve
Cutthetemplateonthecut-outlinelabeled“Self-Rimming
Cut-Out”.
Position the template on the countertop to ensure
clearance between the lavatory, faucet, and backsplash.
Verify cabinet clearance beneath the countertop.
Fig. #7
Use a pencil to trace the template on the countertop.
Re-check the clearance between the lavatory, faucet,
backsplash, and cabinet. Adjust the traced cut-out line
accordingly.
Mark the faucet and handle centerline on the countertop.
Cut out the opening by carefully following the pencil line.
Fig. #8
Template
Trace The Template
Cut-Out

4
1010430-2-AKohler Co., Kohler, WI U.S.A.
CAUTION: Risk of personal injury or product
damage. Large lavatories are very heavy. Get help
lifting the lavatory into place.
Temporarily position the lavatory in the countertop cutout
so the “Kohler” logo is visible. The logo is on the inside
basin, near the rim, and should be positioned near the
faucet.
Verify proper clearancebetween the lavatory, faucet, and
backsplash.
Remove the lavatory from the cutout, and return it to its
protective carton. Do not rest or store the lavatory on the
drain surface.
Drill the faucet holes.
Install the faucet to the countertop according to the
manufacturer’s instructions.
Installthedraintothelavatoryaccordingtotheinstallation
instructions included with the drain. Apply a generous
amountofclearsiliconesealantwhenyouinstallthedrain.
Fig. #9

  
Fortile,wood,orotherporousmaterials,applywaterproof
sealer around the cutout area of the countertop surface.
Follow all manufacturer’s instructions and warnings.
Allow the sealer to dry before proceeding.
Use a 50/50 mixture of isopropyl alcohol and water to
clean the countertop surface around the cutout area.
Wipe dry with a clean cloth.
NOTE: Install the adhesive seal when the temperature is
atleast50°F(10°C). Thepreferredtemperature rangeto
applythe adhesive sealis 70°F (21°C) to100°F (37°C).
Loosely apply the adhesive seal (included) around the
entire countertop cutout so it is about 3/16” (5mm) from
the cutout. Adjust the placement of the seal before
removing the backing material. Cut off any excess seal
material. Carefully remove the adhesive seal backing
material.
Fig. #10
Adhesive
Seal
CAUTION: Risk of personal injury or product
damage. Large lavatories are very heavy. Get help
lifting the lavatory into place.
Notethelocationofthe“Kohler”logo.Thelavatory should
be installed so the logo is visible after installation.
Carefully position the lavatory in the cutout, and press
down firmly.
Fig. #11
“Kohler” Logo

51010430-2-A
Kohler Co., Kohler, WI U.S.A.
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and check for leakage.
Clean up with a non-abrasive cleaner.
Fig. #12
Nut Gasket
Nut
Gasket
ABOVE-COUNTER INSTALLATION
Cut out the template along the inside of the template
cutout line labeled “Above-Counter Cut-Out”.
Position the template on the countertop.
NOTE: Wall-mount faucet installations: Be sure to
provide sufficient spout overhang into the lavatory basin.
See the roughing-in notes for minimum spout length
information.
NOTE: Countertop faucet installations: Pay special
attention to the spout and handle fit clearance when
locating the faucet, as noted below.
Countertop faucet installations: Use the template to
locate the faucet spout hole centerline on the countertop.
This centerline is recommended to provide adequate
clearancebetweentheedgeofthelavatoryandthespout.
Check for adequate clearance between the backsplash,
faucet spout and handles, and lavatory. We recommend
clearance of at least 1” (2.5cm) between:
the installed lavatory and the faucet spout;
the installed lavatory and the end of the faucet
handles;
the faucet spout and handles, and the backsplash.
Refer to the faucet installation instructions for required
clearance, and mark the preferred faucet hole locations.
Trace the template on the countertop.
Outside Edge
of Lavatory
Backsplash
Fig. #13
Cut-out
Line
Spout
Centerline
1” (2.5cm)
Minimum
Clearance

6
1010430-2-AKohler Co., Kohler, WI U.S.A.
Cut out the opening by carefully following the pencil line.
CAUTION: Risk of personal injury or product
damage. Large lavatories are very heavy. Get help
lifting the lavatory into place.
Temporarily position the lavatory in the countertop cutout
so the “Kohler” logo is visible. The logo is located inside
the basin, nearthe rim,andshould bepositioned nearthe
faucet.
Verify proper clearance between the lavatory, faucet, and
backsplash.
Remove the lavatory from the countertop cutout, and
return it to its protective carton. Do not stand or store the
lavatory on the drain surface.
Fig. #14
Drill the faucet holes.
Install the faucet to the countertop according to the
manufacturer’s instructions.
Installthedraintothelavatoryaccordingtotheinstallation
instructions included with the drain. Apply a generous
amountofclearsiliconesealantwhenyouinstallthedrain.
Fortile,wood,orotherporousmaterials,applywaterproof
sealer around the cutout area of the countertop surface.
Follow all manufacturer’s instructions and warnings.
Allow the sealer to dry before proceeding.
Use a 50/50 mixture of isopropyl alcohol and water to
clean the countertop surface around the cutout area.
Wipe dry with a clean cloth.
NOTE: Install the adhesive seal when the temperature is
atleast50°F(10°C). Thepreferredtemperature rangeto
applythe adhesive sealis 70°F (21°C)to100°F (37°C).
Loosely apply the adhesive seal (included) around the
entire countertop cutout so it is alongside the cutout hole.
Adjust the placement of the seal before removing the
backing material. Cut off any excess seal material.
Carefully remove the adhesive seal backing material.
Fig. #15
Adhesive
Seal
CAUTION: Risk of personal injury or product
damage. Large lavatories are very heavy. Get help
lifting the lavatory into place.
Notethelocationofthe“Kohler”logo.Thelavatory should
be installed so the logo is visible after installation.
Carefully position the lavatory in the cutout, and press
down firmly.
Fig. #16
“Kohler” Logo

71010430-2-A
Kohler Co., Kohler, WI U.S.A.
Connect the faucet supply lines.
Connect the drain assembly.
Open the faucet valves, and check for leakage.
Clean up with a non-abrasive cleaner.
Fig. #17
Nut Gasket
Nut
Gasket

8
1010430-2-AKohler Co., Kohler, WI U.S.A.
IMPORTANT CONSUMER INFORMATION
CLEANINGYOURVESSELS LAVATORY
Keep your Vessels lavatory looking new by rinsing it out
thoroughlyaftereachuse.Do notregularlyuseabrasives
onthe lavatory surface,as thiswill eventuallyscratch and
dull the surface. For stubborn stains, abrasives may be
used sparingly.
CALL US FOR HELP
Here’s what you need to do if you require service:
First review the installation instructions to ensure correct installation. For additional assistance in the USA, call our
Customer Service Department for direct help. You may also contact us at our web site listed below.
Call 1-800-4-KOHLER within the U.S.
Call 001-877-680-1310 within Mexico
Call 1-800-964-5590 within Canada


Fig. #1
Mín. 9”
(22,9cm)
Mín. 27”
(68,6cm)
Mín. 8”
(20,3cm) Máx. 6”
(15,2cm)
ESPACIO LIBRE DE ADA, SÓLO BORDE TERMINADO
3-1/2”
(8,9cm)
34”
(86,4cm)
24” (61cm)
***10”
(25,4cm)
(T)
3/8” FRÍA
Salida de 1-1/4”
(S)
LÍNEA CENTRAL DEL ACCESORIO*
3/8” CALIENTE
***10”
(25,4cm)
17-1/2” (44,5cm) D.
10-3/4”
(27,3cm)
1-1/4” (3,2cm)
**3”
(7,6cm) 6”
(15,2cm)
4” (10,2cm)
1-1/2”
(3,8cm)
4” (10,2cm)
SALIDA DEL DRENAJE
QUE CUMPLE CON LA
NORMA DE ADA
91010430-2-A
Kohler Co., Kohler, WI U.S.A.

SPUN GLASSVESSELS
LAVABOS CON BORDE TERMINADO
Y SOBRE EL MOSTRADOR
K-2276
 

ANTES DE COMENZAR
NOTAS
Utilice estas instrucciones para instalaciones sobre
el mostrador o con borde terminado. Siga sólo las
instrucciones correspondientes a su instalación.
Este lavabo le permite ser creativo y flexible con la
instalación.
El cliente puede elegir entre una instalación de grifo
mural o sobre el mostrador, dependiendo del
decorado y estilo deseado. Se sugiere el uso de un
grifo mural.
Antes de la instalación, revise el buen estado de
todas las piezas. Después, coloque el lavabo
nuevamente en su empaque como protección,
hasta el momento de la instalación.
Durante la instalación, coloque el lavabo en su caja,
como medida de protección.
No coloque o apoye el lavabo sobre la superficie
del drenaje.
Para facilitar la formación del sello adhesivo, instale
el lavabo cuando la temperatura esté entre 70°F
(21°C) y 100°F (37°C).
Las instrucciones contienen información importante
sobre el cuidado, limpieza y garantía - guarde las
instrucciones para el cliente.
HERRAMIENTAS Y MATERIALES
REQUERIDOS
Anteojos de seguridad
Botas de seguridad
Lápiz
Tijeras
Cinta métrica
Espátula
Serrucho de calar
Taladro (broca de 1/2” o mayor)
Sellador transparente de silicona (optativo)
Mezcla de alcohol isopropílico y agua en partes
iguales
Sellador impermeable (para mostradores porosos)
INFORMACIÓN SOBRE ELPRODUCTO
Peso aproximado 18 lbs. (8 Kg.). . . . . . . . . . . . . . . .
PRECAUCIÓN: Riesgo de lesiones personales o
daños al producto. Este lavabo está hecho de
vidrio. Maneje el producto con sumo cuidado para
evitar daños.
DIMENSIONESBRUTAS
Notas para la instalación
(T) Drenaje levantable de 9” (22,9cm).
(S) 14” (35,6cm) (Basado en una tubería vertical de 12” (30,5cm)
que puede requerir cortes).
*El surtidor debe tener al menos 5” (12,7cm) de largo, para que
haya suficiente espacio libre en el lavabo.
**El surtidor debe tener suficiente altura como para despejar un
borde de 3” (7,6cm) y suministrar un espacio de 1” (2,5cm) según
lo establecido por la norma ASME A112.1.2.
***Basado en el modelo K-9018, con 1” (2,5cm) de la pestaña
expuesta.

10
1010430-2-AKohler Co., Kohler, WI U.S.A.
INSTALACIÓN DE MODELOS CON BORDE TERMINADO
Determine el lugar de la línea central del grifo. Considere
los diámetros del chapetón del grifo y de las llaves, la
longitud del surtidor y el espacio libre entre el surtidor y el
borde del lavabo.
Calcule la medida de la línea central del grifo, dividiendo
el diámetro del chapetón entre dos y luego sumando 1/4”
(6mm).
NOTA:Redondeeelcálculoal1/16”(2mm)máscercanos
de ser necesario. Fig. #2
Línea
Central del
Grifo
Divida el diámetro del
chapetón entre dos y
sume 1/4” (6mm)
         
         
    
cumplimiento con los códigos estatales y locales de
plomería;
distancia mínima de 2” (5cm) desde el flujo de
agua, al borde terminado del lavabo. Esto es
importante para asegurar el espacio libre adecuado
al momento de lavarse las manos (consulte la
Fig. #3);
distancia mínima de 1/4” (6mm) entre la parte
superior del grifo y el borde del lavabo (consulte la
Fig. #4).
Trace nuevamente la línea central del grifo, de ser
necesario,paracumplirconestoscriterios.Asegúresede
utilizar la línea demarcada como “Borde del Lavabo”.
Fig. #3
Fig. #4
Mínimo de 2” (5cm)
1/4” (6mm) mín.
Mínimo de 2” (5cm)
Espacio de
Aire
          
          
      
NOTA:       
         
Corte a lo largo de la línea correspondiente a la pared
posterior sobre la plantilla.
Fig. #5
Pared Posterior del
Mostrador Línea de la Pared
Posterior
Mostrador
Línea Central del Grifo
Mínimo de 2” (5cm)
Plantilla de Recorte