Kohler K-19321T User manual

-1-
INSTALLATION INSTRUCTIONS
K-19321T
BATH DRAIN
·
·
Please read these instructions carefully to
familiarize yourself with the required tools,
materials, and installation sequences. Follow the
sections that pertain to your particular installation.
This will help you avoid costly mistakes. In addition
to proper installation, read all operating and safety
instructions
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
!
!
BEFORE YOU BEGINBEFORE YOU BEGIN
NOTES
!
!
!
!
!
Observe all local plumbing and plumbing codes.
Inspect waste and supply tubing; replace if
necessary.
The drain has removable parts.
Drain T is reversible for vertical or horizontal
drainage.
Do not use sharp and hard objects when taking out
the drain plug to avoid scratching it.
""
!
!
!
!
!
T
Tools Required
!
!
!
!
!
!
Assorted screwdrivers
Adjustable or open end wrench
Pipe wrenches
Pliers
Manual hacksaw
Long flat nose pliers
!
!
!
!
!
!
SHANGHAI KOHLER LTD., NO.368, MIN LE ROAD,
FENG XIAN DISTRICT, SHANGHAI, CHINA POST CODE 201419
368 201419
©
©
Copyright Kohler China Investment Co., Ltd. 2016
2016
1260047-T01-B

ROUGHING-IN
202
80
101
280 ~ 540
Fig.#1
1
-2-
INSTALLATION PREPARATIONSINSTALLATION PREPARATIONS
Disassemble the overflow plate kit and the base kit
from the overflow base.
Pull the plug off the drain body.
Fig.#2
2
Fig.#3
3
Fig.#4
4
Pull out the control wire head from the bottom of
overflow pipe. Insert a string into the back of the button
and pull out the whole control wire assembly.
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value UNIT: mm
2 Pull Out
2
1 Pull Out
1
Pull Out
Plug
Strainer
1260047-T01-B

-3-
When installing baths with different height, you may need
to cut the pipes as shown to suit the height of the bath.
Attach the gasket to the overflow ell, as shown. Apply
silicon sealant.
Cut Placement
INSTALLATION
Gasket
Drain Ell
Bath
Wrap the plier head with adhesive tape and then insert
it into the top of the strainer to tighten the drain ell
securely, as shown. Make sure the drain ell tube is
facing the front of the bath. Then apply silicone sealant
around the strainer.
Fig.#6
6
Fig.#8
8
Fig.#9
9
Insert strainer into the gasket, position plain gasket
between the drain ell and the bottom of the bath. Turn
the strainer into the drain ell. Strainer Gasket
Unscrew the valve body using packed wrench.
Fig.#5
5
Cross Wrench
Unscrew Counterclockwise
Trigger Kit
Strainer
Apply Silicon Sealant
Gasket
Overflow Ell
Overflow Pipe
Fig.#7
7
Long Flat Nose Pliers
Strainer
1260047-T01-B

-4-
For vertical drainage installations: assemble parts as
shown. Align the parts with the drain base. Align and
tighten the nuts.
Fig.#11
11
Fig.#12
12
Fig.#13
13
Fig.#14
14
Fig.#15
15
Assemble the overflow plate kit and the base kit back to
the overflow base from the inside of bath tub.
Fig.#10
10
For horizontal drainage installations: assemble parts as
shown. Align the parts with the drain base. Align and
tighten the nuts.
Insert the control wire into the center of the overflow
hole.
After inserting the whole control wire, insert the rib on
the button into the slot on the button base until a "click"
is heard.
Pull the tail of control wire from the drain hole. Pull Out
1260047-T01-B

-5-
Remove the rubber cover from the wire as shown, then
fasten the control wire with the trigger kit.
Fig.#16
16
Hide the control wire into the pipe as shown.
Note: Do not over bend the wire at all
bending positions. Leave arcs as big as
possible to avoid too much pressure.
Otherwise, the button may not restore to its
original position.
Fasten the trigger kit on the strainer.
Push the button on overflow, so the ejector pin of the
trigger kit on high position, then push the plug on the
trigger kit until a "click".
Attention:
After install, push the button repeatedly, make sure the
plug could open and close normally. Run water into the
bath, check the drain connections for leaks.
Fig.#17
17
Fig.#18
18
Fig.#19
19
Control Wire
Cross Wrench
Fasten Clockwise
Trigger Kit
Strainer
Plug
Push Down
Fasten As Shown
Trigger Kit Ejector
1260047-T01-B

MAINTENANCE
Fig.#20
20
·
·
Pull off the plug, unscrew the trigger kit, pull the
control wire out to clean the hair on the wire.
The accessories should be washed with warm water
and a soft cloth or sponge. Do not use abrasive
cleaners or cleaners containing bleach.
·
·
Pull Out
Plug
Strainer
Cross Wrench
Unscrew Counterclockwise
Trigger Kit
Strainer
-6-
1260047-T01-B