Kohler PATIO ECO K-18645T-Y User manual

PATIO ECO
INSTALLATION INSTRUCTIONS
VITREOUS CHINA URINAL
K-18645T-Y
A. HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
The urinals can match different sensors to perform three
flushing modes, respectively 0.5L, 1L and 3L. Please
refer to the table on page 6.
·
·
·
·
A.
·
·
·
·
-
0.513
6
B. NOTES
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
Carefully inspect the new fixture for any sign of damage.
Be very careful while shandling vitreous china products.
B.
·
·
·
·
C. REQUIRED TOOLS AND MATERIALS
·
·
·
·
·
·
·
·
Drill
Open end/adjustable wrenches
Tape measure
Thread sealant tape
Basin Wrench
Screwdriver
Sealant
Recommend the no less than 9mm stainless steel twist
pipe as inlet.
C.
·
·
·
·
·
·
·
·
/
9mm
-1-
, 2012
Copyright Kohler China Ltd., 2012
BEFORE YOU BEGINBEFORE YOU BEGIN
1195721-T01-A

Fig.1
1
ROUGHING-IN
Unit:mm
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
332
180
35
80
600 50 ext
145
55 642
303
G1/2
180
180 5
**
Notice: a. The dimensions above are just for reference.
b. The layout dimensions of water and outlet see
installation step C(Install the hook).
c. ** Indicates the location of inlet pipe, while inlet
connector size is G 1/2.
d. * Recommended dimensions for installation only,
please adjust according to actual situation.
inlet
I
a.
b. C( )
c. ** G 1/2
d. *
-2-
1195721-T01-A

-3-
Fig.2
2
INSTALLATION
A.
B.
(2)
S
S
2
A. INSTALL URINAL SENSOR
B. INSTALL OUTLET CONNECTION
(See Fig.2)
NOTE:
Ascertain the position for outlet connection according to
rough-in dimensions.
Connect the outlet connection with the S-trap way. Insert the
gasket into the S-trap way as shown. Apply sealant on outlet
pipe, connect the outlet connection with outlet pipe.
Fig.2 may be different for different outlet connections.
2~10mm 100
30
1195721-T01-A

C.
3
3
Fig.3
3
C. INSTALL HOOK
(See Fig.3)
Drill 2 mounting holes on the wall and install hook. Fix hook
on the wall by tightening screws.
80
180
Fig.4
4
D.
D. INSTALL INLET PIPE
Insert gasket and nut into the urinal as shown. Connect the
inlet connection with inlet pipe.
180
310
+
35
100
1
2
5
4
3
-4-
Supply Pipe
1195721-T01-A

Fig.5
5
E.
5
S
(S
)
E. INSTALL URINAL
(See Fig.5)
Position the installing hole on the back of the urinal with the
hook. Level the outlet connection which is installed together
with the strainer and the gasket on the S-trap way. Then
insert the outlet connection into the gasket.(while the outlet
connection is inserted, the S-trap way can be crutched by
hard exterded via the gap in the bottom of the urinal to install
it decently.) Then fix the urinal on the hook.
-5-
F.
F. INSTALL BEEHIVE STRAINER
Ascertain the position for beehive strainer as shown. Secure
the beehive strainer by tightening screw.
Fig.6
6
1195721-T01-A

-6-
1. Urinal is designed for use with portable water. Avoid water
that includes a lot of contaminants or with acid/alkali water
and impure water.
2. If you live in a hard water area, ensure that the holes in the
toilet rim are kept clean to ensure proper bowl flushing,
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to
clean as far into the trap as possible to prevent mineral
deposits from forming.
3. Most toilet bowl cleaners are not harmful to the surface of
the urinal, Please follow the bowl cleaner manufacturer's
instructions carefully.
4. Do not use abrasive cleaners to clean surfaces.
5. Do not directly flush the wire connector of sensor with
water.
6. Do not place Sensor window near strong ultraviolet and
electromagnetism.
7. Keep the sensor window clean. Do not cover the sensor.
The sensor cover can be cleaned by the soft rag. (with
neutral liquid detergent). Do not use any eradicator,
abrasive powder or the oil, acid or alkali liquid detergent.
Do not pour air freshener, disinfectant or any other kinds of
liquid to the sensor directly.
8. Please flush and clean the urinal regularly to avoid pipe
blockage.
9. Please use sensors that match the urinal. Kohler shall not
be responsible for any damage caused by using sensors of
other brands.
1.
2.
3.
4.
5.
6.
7.
8.
9.
CONSUMER RESPONSIBILITIES
WARNING: Risk of product damage.
Do not throw into the urinal what is easy to block it,
such as newspaper, paper pilch.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.
o
CAUTION: Please do not use hard materials (like
scouring pad) to clean product surface, especially the
product logo.
0C
o
(Table) Sensors matched with Urinals
0.5L
8881T-YC01/
YC03-BN
8791T-YC01/
YC03-CP/SC
PSD
1.0L
8881T-C01-BN 8988T-C01/
C03-CP/SC
PSD
3.0L
8122T-C01-
CP/SC
8787T-B01/
B03-CP/SC
8791T-C01/
C03-CP/SC
8872T-C01/
C03-CP/SC
1195721-T01-A