Kohler PARALLEL K-31139T-4-BL User manual

INSTALLATION INSTRUCTIONS
安装说明书
Floor Mount Bath Filler without Handshower
若方
PARALLEL
1484894-T2-A 1
31139T-4 落地式浴缸龙头(不含手持花洒)
BEFORE YOU BEGIN
安装之前
All information is based on the latest product
information available at the time of publication.
Kohler Co. reserves the right to make changes in
product characteristics, packaging, or availability at
any time without notice.
Please leave these instructions for the consumer.
They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove
debris.
2. Inspect the supply tubing for damage. Replace if
needed.
3. Observe local plumbing codes.
4. Check for leaks before covering the pipes, repair if
needed.
5. Please purchase the matched mounting base
97905T when install the faucet.
所有的资料是按最新出版的产品资料编写而成。科勒
公司保留任何时候不经通知即可改变产品特性、包装
或产品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，请
把这些资料交给用户阅读。
注意事项：
1. 一定要先彻底冲洗供水管以清除管道中的杂质。
2. 检查供水管有无损坏。如需要，进行替换。
3. 遵守当地管路安装条例。
4. 预埋前测试安装连接部位是否有渗漏，根据需要修
理之。
5. 安装本产品时请与97905T配套使用。
*请根据图示尺寸选择合适的浴缸
*Please purchase the appropriate bathtub according to the dimension.
安装尺寸 ROUGH-IN DIMENSIONS
57
846~866
Ø60
117
270
10º
782~802
125×125
*221
630 最大
630 Max.
浴缸
Bathtub
70 最小
70 Min.

1484894-T2-A 3
1484894-T2-A 2
安装步骤 INSTALLATION
关闭水源。用锯条贴地砖表面锯除预
埋底座上保护罩(1)露出部分，并取下
塞头(2)。从龙头上取下保护套(3)。
上滑装饰盖组件(4)， 安 装 龙 头 。
注意：安装时请保持龙头垂直装入，
防止破坏底部O型圈。
将龙头出水口正对浴缸，用螺钉(5)套
上垫片(6)通过法兰盘(7)将龙头固定到
底座上。用六角扳手(8)锁紧螺钉。
下滑装饰盖组件使其贴紧地面。
如何安装龙头 How to Install the Faucet
Shut off water supply. Cut away the
extending part of the base protector(1)
in accordance with the tile surface.
Remove the plug(2) from the base.
Remove the protector(3) from the faucet.
Slide up the escutcheon kit(4). Install the
faucet. NOTE: Keep the faucet vertical
to the base, to avoid damaging the
O-rings on the bottom.
Keep the spout pointing to tub. Fix the
faucet to the base with the screws(5)
and washers(6) through the flange(7).
Tighten the screws with hex wrench(8).
Slide down the escutcheon kit until it is
against the finished floor.
Floor Mount Bath Filler without Handshower
**订购时请说明颜色编号
**Color code must be specified when ordering
SERVICE PARTS
零 件 图
若方
PARALLEL
31139T-4 落地式浴缸龙头(不含手持花洒)
清洗说明 CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗镀
层表面，再以干净的软布彻底擦干整个表面，许多清
洁剂，比如氨水、去污粉及洁厕灵等，会对电镀表面
造成伤害，切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的
水龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean
soft cloth. Many cleaners may contain chemicals, such
as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended
for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
使用说明 HANDLE OPERATION
将把手轻轻提起，顺时针旋转为热水，逆时针旋转
为冷水。
Lift the handle gently. Turn clockwise for hot water,
turn counter-clockwise for cold water.
Ensure all coupling nuts are tight.
Ensure the handle is in the off position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Remove the aerator(10) with tool(9).
Run hot and cold water through spout for
about one minute to remove any debris.
Check for leaks at this time. Shut off
water supply. Reinstall the aerator.
安装结果检查
INSTALLATION CHECKOUT
检查并确保所有衔接螺母都已拧紧，
确保手柄在关闭的位置。
开启主水源，检查是否漏水。如有漏
水，修理之。
用工具(9)拆下起泡器(10)。打开冷热
水，让水流约一分钟以清除杂质。检
查渗漏，关闭水源，装回起泡器。
1333529**
1333434**
1333433
1333432
77950
1229992
1358690**
77955
38618
1337774
3013706
1333448
1258088
1381532
833438
77955
1082901
1010167
65218
3006148
1245237
(仅用于BL表面)
(Only for BL finish)
3008523
(用于其它表面)
(For other finishes)
5
4
7
8
1
6
2
3
10
9
1245237
(仅用于BL表面)
(Only for BL finish)
3008523
(用于其它表面)
(For other finishes)