Kohler STRAYT 37331A-4ND User manual

All information is based on the latest product information available at the time of publication. Kohler Co.
reserves the right to make changes in product characteristics, packaging, or availability at any time without
notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. If possible, install this faucet before installing the lavatory.
3. Shut off the water supply to the fittings before installing.
4. An in line water filter must be used with this product.
5. Inspect the supply pipes for damage. Replace as necessary.
6. Observe local plumbing codes.
7. Recommended working pressure: 100KPa to 500KPa.
8. Maximum working pressure: 800KPa.
9. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
1167539-AN2-A
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
Two-Handle Widespread Lavatory Faucet 37331A-4ND
STRAYT
BASIN TAPWARE
1
1167539-AN2-A 25/05/16 25/05/16
4
ROUGH-IN DIMENSIONS
SPARE PARTS
**Color code must be specified when ordering
Ø32~Ø38
G1/2"
Ø30~Ø42
10~45
46x46
200~750
50x50
15º
135
115
138
88
74.5
STRAYT
BASIN TAPWARE
1162050**
Handle (Hot)
1119280
Valve
78125
Adapter
1041022
Screw
1162052**
Escutcheon
830915
Washer
864342
Nut
1156038
Side Body Kit
1021514
Extension Stem
1040731
Screw
1167441**
Nut
1088919
Aerator
1162051**
Escutcheon
834704
Hardware kit
1054593
Hose
1041022
Screw
1162052**
Escutcheon
1119281
Valve
78125
Adapter
1162049**
Handle (Cold)
830915
Washer
864342
Nut
1156038
Side Body Kit
1182548
Screw
1010167
O-ring
1167441**
Nut
1010167
O-ring
1040731
Screw
1021514
Extension Stem
833730
Hex Wrench
3006147
Key
1119982
1126106
Two-Handle Widespread Lavatory Faucet 37331A-4ND

1.) Screw the studs(1) into the thread holes in the bottom
of the spout.
2.) Feed the washer(2) over the hoses(3) and studs(1),
and put the washer into the groove on the bottom of
the escutcheon(4).
3.) Insert the hoses and studs into the central hole of the
lavatory and position the spout.
4.) From the underside of the lavatory, fit the brackets(5),
with the rubber washer on top, onto the studs.
5.) Secure the spout by tightening the nuts(6).
INSTALLATION - Spout
1167539-AN2-A
3
1167539-AN2-A
2
1.) Remove the nut(9) from each valve body(8).
2.) Put the O-rings(10) into the groove on the bottom of
each escutcheon(11).
3.) Insert the valve bodies through mounting holes from
the bottom of the lavatory.
NOTE: Ensure the valves are closed before installation,
and that the valve with red dot (hot) is on the left when
facing the front of the faucet.
4.) Install the escutcheon onto each valve body, and then
tighten the nuts(9) to secure.
5.) Loosen the grub screw(14) on each handle(13) with the
hex wrench(12), then press handles onto the extension
stems(15).
NOTE: Valves should be in closed position before
installing and the handle with red mark should be
installed on the left when facing the front of the faucet.
6.) Tighten the grub screws with the hex wrench to secure
the handles. Use a wrench to tighten the nuts(7).
7.) Attach the hoses(3) to the valve bodies(8).
NOTE: When facing the front of the faucet, the left hose
connects to the left valve body, the right hose connects
to the right valve body.
INSTALLATION - Handles
2
1
4
5
6
3
9
11
15
12
13
Hot tap
Cold tap
14
7
83
10
1.) Ensure that all connections are tightened and that
the handles are in the off position.
2.) Open the drain, turn on main water supply and
check for leaks. Repair as required.
3.) Remove the aerator(16) with the key(17).
4.) Turn the faucet handle on. Run hot and cold water
through the spout for about one minute to remove
any debris. Remove debris from the aerator.
5.) Shut off the faucet and reinstall the aerator.
INSTALLATION CHECKOUT
1.) Clean the finish with mild soap and warm water.
2.) Wipe entire surface completely dry with clean soft cloth.
NOTE: Many cleaners may contain chemicals such as ammonia, chlorine, toilet cleaner etc. which could
adversely affect the finish and are not recommended for cleaning.
NOTE: Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
17
16
HANDLE OPERATION
1.) Left handle opens with a quarter turn anti-clockwise.
2.) Right handle opens with a quarter turn clockwise.
Handles in off position Handles in on position
25/05/16 25/05/16