Kohler 74036T-4E2 User manual

1287816-2A-B 1
BEFORE YOU BEGIN
HANDLE OPERATION
Lift handle gently. Turn clockwise for hot water, turn counter-colckwise for cold water. Water flows out from spout
when faucet diverter is in the normal position; lift the diverter gently, turn clockwise for handspray; shut off the
faucet, turn counter-clockwise until it stops.
1287816-2A-B 4
INSTALLATION INSTRUCTIONS
74036T-4E2 Wall Mount Bath Shower Faucet
74035T-4E2 Wall Mount Shower Faucet
74036T-4E2 Wall Mount Bath Shower Faucet
74035T-4E2 Wall Mount Shower Faucet
TAUTTAUT
ROUGH-IN DIMENSIONS
SERVICE PARTS
1500
G1/2˝
G1/2˝
G1/2˝
87
Ø90
226
49
40º
27
60
58
74036T-4E2
128
171
187
18º
G1/2˝
G1/2˝
150±15 66
Ø66
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes.
4. The minimum inlet water pressure for the diverter is 0.05MPa.
5. The highest working pressure for handspray is 0.5MPa. If it exceeds 0.5MPa, a pressure reducer is needed. The
highest water and environment temperature is 60°C. Please keep handspray, showerhead and the shower arm
away from heater, or it may become damaged and cause injury to the user.
**Color code must be specified when ordering.
1181007**
1219595**
3008523
3013706
1242786**
1209778**
1209777
1292054
864104**
1213567
3016381
1153258
831727**
74036T-4E2:3020067
74036T-4E2:1284457**
74036T-4E2:1223033**
74036T-4E2:1242725
74036T-4E2:1223039
1216770**
74035T-4E2:3016381
74035T-4E2:1213561

1287816-2A-B 2 1287816-2A-B 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
How to Install the Faucet
Use appropriate thread sealants or thread tape on
pipe threads. Install the two offset connectors(1) into
the hot and cold supply pipes.
Adjust the center-to-center distance between the
connectors to 150mm and horizontally. They should
extend 29mm from finished wall. Thread the
escutcheons(2) onto the connectors until they contact
the finished wall.
Put the washers(3) into the nuts(4). Thread the nuts
onto the connectors(1) and tighten by wrench.
How to Install the Handshower
Remove the guard on the outlet connector firstly.
Put the washer(5) into end A of the hose(6), and then
connect to the faucet outlet(7). Put the washer(8) into
end B of the hose, and install the regulator(9) into the
handshower(10) inlet if needed, then connect end B of
the hose to the handshower inlet.
How to Install the Bracket
Determine a suitable location on the finished wall to
install the bracket. Mark bracket base mounting hole
locations on the wall according to the dimension. Drill
two holes on the finished wall, the holes should match
the anchors(11). Install the anchors.
Tighten screws(12) to secure bracket base(13, flat
side upward). Put the bracket(14) onto the bracket
base and lock by stopper.
Ensure that all coupling nuts tightened.
Ensure that the handle is in the off position.
Turn on the main water supply, and check for leaks.
Repair as needed.
74036T-4E2: Wall Mount Bath Shower Faucet
Remove the handshower(10), remove the aerator(16)
by coin. Run hot and cold water through the faucet for
about one minute to remove any debris. Check for
leaks. Remove any debris from the aerator.
Lift the diverter(15) gently, turn clockwise for shower.
Run hot and cold water through the faucet for about
one minute to remove any debris. Check for leaks.
Shut off the faucet, reinstall the handshower and
aerator .
74035T-4E2: Wall Mount Shower Faucet
Remove the handshower(10). Run hot and cold water
through the faucet for about one minute to remove
any debris. Check for leaks. Shut off the faucet,
reinstall the handshower.
Cold
Hot 1
2
150mm
29mm
27
12
14
13
11
10
8
7
9
B
5
A
6
10
15
16
10
3
4
1500
G1/2˝
G1/2˝
G1/2˝
87
Ø90
226
49
40º
27
60
58
74035T-4E2
G1/2˝
G1/2˝
56
130
150±15
Ø66