Kohler STRAYT 37337T-B4 User manual

1338592-2A-A 1
INSTALLATION INSTRUCTIONS
37337T-B4/B4DPR/B4DPW Deck-Mount Bath & Shower Faucet37337T-B4/B4DPR/B4DPW Deck-Mount Bath & Shower Faucet
BEFORE YOU BEGIN
HANDLE OPERATION
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. If possible, install this faucet before installing the bath.
5. The highest working pressure for handshower & showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower,
showerhead and shower arm away from heater, or it may become damaged and cause injury to the user.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
1338592-2A-A 4
SERVICE PARTS
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
Lift the handle gently. Turn clockwise for hot water, counter-clockwise for cold water. Water flows out from spout
when diverter is in the normal position and it’s diverted to handshower when the diverter knob is lifted.
STRAYTSTRAYT
37337T-B4:1154948**
3006923**
3006930
3025497
3006991
833438
834705**
834705**
835696
3006376
834361
835696
835696
864718
834428
50903
1108464
39924
75100**
898324**
3021164
1162079
1162080**
1043069
3025496
3025495
37337T-B4DPR:1188277**
37337T-B4DPW:1192957**
833438
3013947
831587
831587
1162082**
1162081**
3013947
1043069
77949
1053352
1045376
1167478**
3005148
1162078**
66633
1107103
46112
1043069
22352
1128531
3002530
3006148
66637
1046290
1297484**
1030624
77420
1240266
ROUGH-IN DIMENSIONS
G1/2˝
65
78.8
480
65 65
146 146
Ø38~Ø40 Ø39~Ø41
Ø32~Ø40
Max．40
260 18 53.3
53.3
53.3
110
83.4
53.3
65
65
217
9°
150
177
G1/2˝
28 28
240
250

1338592-2A-A 2 1338592-2A-A 3
INSTALLATION
CLEANING INSTRUCTIONS
INSTALLATION CHECKOUT
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
How to Operate the Handshower
Press the buttons of the handshower to change the water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow stream to become
distorted or reduce the flow rate. To remove the debris or mineral build-
up, run water through the handshower, firmly press or rub your finger
back and forth across the rubber nozzles.
Remove and clean the screen washer.
2
7
8
9
3
1
4
5
6
21
24
16
17
20
14
11 12
13
10
25
28
27
19
23
22
15
29
30
18
26
42
Katalyst Air
Intense Massage
C
41
40
D
32
31
34
33
35
36
38
B
A
39
37
40
44
43
39
How to Install the Valve Kit
Put the rubber washer(3) into the groove on the bottom of the escutcheon(4).
Fit the valve kit(1) to the hole of the bath tub.
From underside of the bath tub, install the parts according to the following
order: washers(2), washer(7) and ring(8). Position the valve kit so that the
connector(5) of the valve kit is on the back. Adjust the ring to the appropriate
position. Tighten the screws(9) to secure the valve kit.
Attach the hoses(6) to water supplies. The hose with “COLD” mark connects
to cold water.
How to Install the Spout
Loosen the screws(12) of the lift rod knob kit(11) with the hex wrench(10),
and remove the lift rod knob kit. Remove the plug(14) from the spout kit(13).
Loosen the screw(16) with the hex wrench(15), and remove the diverter
kit(17). Put the ring(18), washer(19) and washer(20) to the lower location of
the diverter kit. Slide the o-ring(21) into the bottom groove of the nut(22). Put
the washer(23) into the bottom groove of the escutcheon(24).
From underside of the bath tub, insert the diverter kit into the hole of bath tub
and put out it as much as possible. Slide the escutcheon with the washer
onto the diverter kit, and keep it against the bath tub. Tighten the nut(22)
with o-ring onto the diverter kit. Position the diverter kit so that the nut(25) is
on the left. Adjust the ring to the appropriate position. Tighten the screws(26)
to secure the diverter kit.
Install the spout kit onto the diverter kit, position the spout kit so that the
spout points to the front. Install the lift rod knob kit onto the lift rod(27), and
tighten the screw(12) with the hex wrench(10). Tighten the screw(16) with
the hex wrench(15), and install the plug.
Install the washer(28) into the connector of hose(29), then connect the
connector(5) of valve kit and the connector(30) of diverter kit with the hose.
Ensure that all coupling nuts are tight. Ensure that the handle is in the off
position.
Turn on the drain and main water supply, and check for leaks. Repair as
needed.
Remove the aerator(44) with the key(43). Remove the handshower(39).
Turn on faucet handle. Run hot and cold water through spout about one
minute to remove any debris. Check for leaks at this time. Remove any
debris. Shut off the faucet. Reinstall the aerator and the handshower.
How to Install the Handshower
Remove the parts from shank(31) and retain them according to the following
order: washer(32), washer(33) and nut(34). Slide the washer(35) into the
bottom groove of the escutcheon(36), install the escutcheon with washer to
the shank and tighten it, then fit the shank to the hole of the bath tub.
From underside of the bath tub, install the washer(32), washer(33), nut(34).
Position the escutcheon so that two arc edges are symmetrical up and
down. Tighten the nut(34).
Install regulator(37) into the handshower(39) inlet if needed. Connect the
connector(A) of the hose(38) to the handshower, connect the other
connector(B) of the hose(38) to the connector(C) of the hose(40). Install the
washer(41) into the connector(D) of hose(40), then connect to the
connector(42) of the diverter kit.