Kohler K-31333TW-0 User manual

English page 2-9
Kohler China Investment Co., Ltd.
No.158, Jiangchangsan Road, Jing'An District, Shanghai, PRC Post Code : 200436
Manufacturer: Shanghai Kohler Electronics., Ltd.
No. 1955, Fengxiang Road, Baoshan Area, Shanghai, PRC Post Code : 200444
Installation Guide
Smart Seat
C3-520
K-31333TW-0
1350315-TW01-A
10-17

Thank You For Choosing Kohler Company
Thank you for choosing a Kohler product. Kohler craftsmanship offers you a
rare combination of proven performance and graceful sophistication that will
satisfy you for years to come. The dependability and beauty of your Kohler
product will surpass your highest expectations. We are very proud of our
products here at Kohler and we know you will be too.
Please take a few minutes to study this Homeowners Guide. Pay special
attention to the care and cleaning instructions.
All information in this manual is based upon the latest product information
available at the time of publication. At Kohler, we constantly strive to improve
the quality of our products. We reserve the right to make changes in product
characteristics, packaging or availability at any time without notice.
1350315-TW01-A
2
Kohler Co.

Before You Begin
Tools and Materials
□
□
□
□
□Follow local plumbing and construction codes.
□Do not use extension cord with the product.
□
□
□
□
□Connect only to tap water.
□Unplug the seat and drain completely, if the seat is not being used for an
extended period of time.
□
Adjustable wrench Blade Screwdriver Tape Rag
Note:
Warning:
Risk of electric shock, fire hazards, or personal injury. This product must
be installed safely. Connect only to dedicated 110V~, 50Hz/60Hz, 15A circuit
protected by Ground-Fault Circuit-Interrupters (GFCI’s) or Earth-Leakage
Circuit-Breakers (ELCB’s).
Risk of electric shock or product damage. Do not immerse the product into
water.
Risk of product damage. Do not plug in the seat until all other installation
steps have been completed.
Risk of product damage. Do not install at a place where it may be splashed
by water.
Risk of product damage. Do not install the product at a place with excessive
humidity, where moisture may condense at the surface of the product. Please
maintain that the usage environment is under adequate ventilation, so as to
prevent damage to electronic components.
Risk of product damage or property loss. Water leakage may happen if the
water pipe connector is pulled or pressed with excessive force.
Risk of product damage. The product may be damaged if the nozzle is
applied with excessive force.
Risk of product damage. Make sure the seat is positioned correctly so that it
can be connected to the thread of the inlet pipe. Otherwise, the inlet pipe
thread may wear off and lead to water leakage.
□Min water pressure 0.07Mpa (dynamic pressure)
Max water pressure 0.74Mpa.
When install the product in the room, a stop valve shall be installed in a close
proximity. For emergency circumstances, the water inlet valve shall be stopped
without using any tools; otherwise unexpected failure may cause the loss to the
customer.
Kohler Co.
3
1350315-TW01-A

1. Distance between installation holes: 136 - 210mm.
2. Distance between installation holes and tank front rim: >20mm.
3. Distance between installation holes and bowl inner rim: <70mm.
4. Distance between installation holes and tank top rim: 460 - 490mm.
5. Bowl inner diameter: 370 - 390mm.
6. The distance between the seat and the plug should be maximum 1 meter.
1. Toilet roughing-in requirements and installation tips
2. Install an Electrical Outlet
1
2
3
4
5
3. Preparation
WARNING: Risk of electric shock, fire, or personal injury.
It is recommended to use water-resistant socket. Do not use an
extension cord with the product.
NOTE: Follow local codes when determining the electrical outlet location.
Turn off the water supply to the toilet.
Flush the toilet to relieve any pressure from the water supply hoses.
Place a container under the inlet valve to catch any residual water.
Disconnect the water supply hose from the inlet valve.
Remove the existing toilet seat.
110V AC
This product must be grounded. Connect only to a dedicated
110V~, 50Hz/60Hz, 15A circuit protected by Ground-Fault Circuit-
Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).
Route the electrical and install to a 110V~, 50Hz/60Hz, 15A GFCI- or ELCB-
protected receptacle.
1350315-TW01-A
4
Kohler Co.

4. Install the Mounting Plate
Screw
Nut
Kohler Co.
5
1350315-TW01-A

5. Install the Seat
For Toilets with Threaded Inserts:
Arrow 2
Arrow 1
Arrow 1
Mounting
plate
Slightly lift cover front tip, observe rear bugle slot, guide mounting plate into
the groove (per arrow 1 direction) Align the slot on the mounting plate with the
groove located below the toilet seat.
Slide the seat onto the mounting plate, front tip downwards (per arrow 2
direction) until you feel it snaps into place.
For Toilets without Threaded Inserts:
To adjust cover position, do not remove cover; only loosen screws to adjust
cover and mounting plate position. Tight down the bolts when desired position
is acquired.
To adjust cover position, remove cover first, readjust mounting plate position.
Once the mounting plate is confirmed, tighten screws, fasten mounting plate,
re-install cover.
1350315-TW01-A
6
Kohler Co.

Open cartridge cover when use filter first time.
Tighten all connections.
Tighten filter inlet
Connect to cover
Connect to water tank
IMPORTANT! Risk of product damage. Align water inlet hose thread with cover
thread, do not damage threads or over tighten connector. To tighten the connector,
manually tighten and tight 1/4 turns more by tool.
IMPORTANT! Risk of product damage. Do not scratch the product surface.
NOTE! For those newly installed plumbing pipes, (before the inlet hose is
connected to the T-valve,) flush for several seconds to to remove the dirt and
debris, etc inside the hose.
Connect cover and water tank with supplied hose.
Note: use supplied new hose, do not reuse the old hose.
Adjust filter angle and position (for easy exchange in the future, cartridge
exchange refer to “Homeowner’s Guide” on page 14).
Adjust exchange duration to 6 months.
Turn on water supply system
Note! Flush the water supply pipes completely to remove debris. The product
is designed for tap water. Make sure not to use industrial water/sewage water/
waste water/ocean water.
Check water leak, adjust if necessary.
Connect the T-valve directly to the water inlet valve.
Rotate and install cartridge cover properly (refers to Homeowner’s Guide on
Page 14).
6.1 Connect the Water Supply (K-31333TW-0)
Kohler Co.
7
1350315-TW01-A

Use supplied hose to connect Tee-valve to toilet.
IMPORTANT! Risk of product damage. Align water inlet hose thread with cover
thread, do not damage threads or over tighten connector. To tighten the connector,
manually tighten and tight 1/4 turns more by tool.
IMPORTANT! Risk of product damage. Do not scratch the product surface.
Connect the T-valve directly to toilet or the water inlet valve.
NOTE! For those newly installed plumbing pipes, (before the inlet hose is
connected to the T-valve,) flush for several seconds to to remove the dirt and
debris, etc inside the hose.
Note: use supplied new hose; do not reuse the old hose.
Tighten all connections.
Turn on water supply system
Note! Flush the water supply pipes completely to remove debris. The product
is designed for tap water. Make sure not to use industrial water/sewage water/
waste water/ocean water.
Check water leak, adjust if necessary.
6.2 Connect the Water Supply (K-31333TW-0)
1350315-TW01-A
8
Kohler Co.

7. Installation Checkout
Ensure if water inlet valve is OPEN.
Wrap seat with plastic sheet to prevent splash water from toilet during test.
Toilet generates one short beep once it is plugged in. The nozzle stretches
out and draws back once. Backlight on the side panel lights up and the night
light flashes until the initialization process completes.
Snap hose and power cord into the clip.
The seat is designed not to function without an occupant. To activate the seat
controls for testing purposes, when facing the toilet, place your hand or a damp
wash cloth on the right side of the seat approximately 1/3 from the front of the
seat (sensor area).
Proceed to the “Keypad and Panel Diagram” Section to test the various seat
functions.
Kohler Co.
9
1350315-TW01-A

謝謝您選擇科勒公司
請花幾分鐘閱讀一下這本用戶手冊，特別注意維護和清洗說明。
謝謝您選擇科勒。科勒技術提供了可靠性能和優雅生活的結合，滿足了
您未來幾年的需求。科勒產品的美觀和可靠性將滿足您最挑剔的眼光。
我們為我們科勒的產品感到非常地自豪，相信您也會。
這本說明書中所有的資訊基於最新公開的產品資訊。在科勒，我們一貫
堅持改善我們產品的品質。我們保留在任何時候不通知的情況下改變產
品特性，包裝或實用性的權利。
1350315-TW01-A
10
Kohler Co.