Kohler K-76395 User manual

Installation Guide
Wall-Hung Toilet with Cleansing Seat
Français, page “Français-1”
Español, página “Español-1”
K-76395
1247364-2-A

Before You Begin
NOTE: This product is designed for installation with the electrical
and water supplies located through the wall.
WARNING: When using electrical products, basic
precautions should always be followed, including the
following:
WARNING: Risk of electric shock. Grounding this product
improperly can result in a risk of electric shock.
DANGER: Risk of electrocution. Disconnect the electricity
to the working area at the main breaker panel before
performing the installation steps for hardwiring.
WARNING: Risk of electric shock. Connect only to a circuit
protected by a Ground-Fault Circuit-Interrupter (GFCI)*
WARNING: Risk of electric shock. Grounding is required. A
qualified electrician should make all electrical connections.
WARNING: Risk of electric shock. Disconnect power before
servicing.
WARNING: Risk of injury or property damage. Please read
all instructions thoroughly before beginning installation,
including the following requirements.
If repair or replacement of the power cord becomes necessary, do
not connect the grounding wire to either of the other terminals.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the product is properly grounded.
NOTE: When lifting the bowl into place, the process is more
efficient when performed by two people.
Observe all local plumbing and building codes.
*Outside North America, this device may be known as a Residual
Current Device (RCD).
Grounding Instructions
This product should be connected to a grounded, metallic,
permanent wiring system, or an equipment-grounding conductor
should be run with the circuit conductors and connected to the
equipment grounding terminal or lead on the product.
1247364-2-A 2 Kohler Co.

Before You Begin (cont.)
This product is intended for hardwire installation. Make sure
electrical power can be provided to the installation area.
The installation must have a Class A Ground-Fault
Circuit-Interrupter (GFCI). The GFCI protects against
line-to-ground shock hazard. Use a 100 VAC - 240 VAC, 50 Hz -
60 Hz supply.
Tools and Materials
Plus:
• Rug or Protective
Material
3/4"
Plumbers
Silicone Grease
Kohler Co. 3 1247364-2-A

1. Remove the Side Panels
Remove and set aside the side panels from the bowl.
1247364-2-A 4 Kohler Co.

2. Mark the Pipes - Bowl Side
IMPORTANT! If silicone plumbers grease is not applied to the
gaskets, they will bind during fitting, which will result in the pipes
being cut to incorrect lengths.
NOTE: This step is easier with the bowl upside down.
Install the gasket on the ribbed end of the inlet pipe.
NOTE: The outlet pipe gasket comes positioned on the thin portion
of the outlet pipe. Remove the gasket and reinstall it as shown.
Install the outlet pipe gasket on the flared end of the outlet pipe.
Apply silicone plumbers grease to the outlet pipe gasket.
Firmly fit the outlet pipe and gasket over the bowl outlet,
pushing until it contacts the bowl.
Position a level or other straight edge across the back of the bowl.
Mark the outlet pipe at the back edge of the bowl using the level
as a guide.
Apply silicone plumbers grease to the outside of the inlet pipe
gasket.
Straight Edge
or Level
Gasket
Inlet
Pipe
Outlet
Pipe
Gasket
Silicone
Plumbers
Grease
Outlet
Pipe
Inlet Pipe
Silicone
Plumbers
Grease
Kohler Co. 5 1247364-2-A

Mark the Pipes - Bowl Side (cont.)
Firmly insert the gasket end of the inlet pipe into the water inlet,
pushing until it contacts the bowl.
Position a level or other straight edge across the back of the bowl.
Mark the inlet pipe at the back edge of the bowl using the level
as a guide.
Remove the inlet and outlet pipes.
1247364-2-A 6 Kohler Co.

3. Mark the Pipes - Wall Side
Remove and discard the plaster guards from the inlet and outlet
holes.
Apply plumbers grease to the gasket in the opening of the inlet
and outlet holes.
Firmly insert the inlet pipe completely into the inlet hole.
NOTE: If the finished wall aligns with any portion of the gasket
section of the inlet pipe, no mark or cut is needed.
Use a level or other straight edge to mark the inlet pipe even
with the front edge of the finished wall.
Firmly insert the outlet pipe completely into the outlet hole.
NOTE: If the finished wall aligns with the wide part of the outlet
pipe, no mark or cut is needed.
Use a level or other straight edge to mark the outlet pipe even
with the front edge of the finished wall.
Remove the inlet and outlet pipes.
Finished Wall
Inlet Hole
Plaster
Guard
Outlet Hole
Outlet Pipe
Inlet Pipe
Kohler Co. 7 1247364-2-A

4. Cut the Pipes
Measure the distance between the two marks on the inlet pipe to
determine ″X.″
Measure and mark ″X″from the end opposite the gasket on the
inlet pipe.
Cut the inlet pipe at this location.
Measure the distance between the two marks on the outlet pipe
to determine ″Y.″
Measure and mark ″Y″from the end of the side opposite the
gasket on the outlet pipe.
Cut the outlet pipe at this location.
Use a file to remove all rough areas on the cut end of each pipe.
X
Y
Outlet Pipe
Inlet Pipe
Y
X
1247364-2-A 8 Kohler Co.

5. Install the Pipes
NOTE: Be sure that the gaskets on the inlet and outlet holes are still
well lubricated with plumbers grease. Apply more plumbers grease
if necessary.
Insert the inlet pipe into the inlet hole
Insert the outlet pipe into the outlet hole
Inlet Hole
Inlet Pipe
Outlet Pipe
Outlet Hole
Apply plumber's
grease.
Kohler Co. 9 1247364-2-A

6. Adjust the Threaded Rods
Adjust the threaded rods until they each extend 3″(76 mm) from
the finished wall.
Place a washer onto each threaded rod.
Thread one of the jam nuts over each threaded rod and tighten
down to lock the rods in position.
Threaded Rod
3"
(76 mm)
1247364-2-A 10 Kohler Co.