Kolcraft KW031 User manual

Consumer Service: 1.800.453.7673
www.kolcraft.com
Model #: KW031
W033-R2 02/2021
Scan for Spanish instructions
Escanee para obtener instrucciones en español

2
Consumer Service: 1.800.453.7673
www.kolcraft.com
Read all instructions BEFORE assembly and USE of the walker. Failure to follow these
warnings and instructions could result in serious injury or death. For your child’s safety,
read the labels and the instructions before using product.
Keep instructions for future use.
IMPORTANT SAFETY INFORMATION:
How to Keep Your Child Safe While Using this Product
• NEVER leave child unattended. Always keep child in view while IN WALKER.
• CAUTION: Toys intended to be assembled by adult! Toys are intended to be played
with while attached to the walker and are not intended to be played with when not
attached to the walker.
• CHOKING HAZARD-Small parts. ADULT ASSEMBLY REQUIRED.
This package contains small parts which, before assembly, present a choking hazard to
children under the age of three. Care should be taken during unpacking and assembly to
insure that all small parts and plastic bags are accounted for and kept out of the reach of
children. All fasteners should be fully tightened.
STAIR HAZARD
• Avoid serious injury or death. Block stairs / steps securely before using this walker.
• Use only on flat surfaces free of objects that could cause this walker to tip over.
Never use near stairs, steps, thresholds, hills, roadways, or pools.
• To avoid burns, keep child away from hot liquids, stoves, radiators, space heaters,
fireplaces, etc.
• Discontinue using this walker should it become damaged or broken.
• Never carry this walker with child in it. Never adjust seat while child is in product.
• DO NOT lift or carry by tray or toys.
• DO NOT use this walker until baby can sit up unassisted.
• To reduce the chance of child slipping out of seat, check that both feet of child touch the
floor.
• Discontinue use of activity walker (seated stage) when your child can stand unaided, walk
unassisted or lift the walker off of the floor.
• To maintain stopping performance, clean friction strips regularly with damp cloth.
Only use this activity walker (seated stage) if your child MEETS ALL of the
requirements below:
1. Can support body weight with legs
2. Weight is between 15 and 26 pounds (6.8 and 11.8 kgs)
3. Height is less than 32 inches (80 cms) and child is not able to stand flat footed while in
the walker.
mWARNING

3
Consumer Service: 1.800.453.7673
www.kolcraft.com
To prevent battery leaks, which can burn skin and eyes:
• Remove batteries when storing product for a long time.
• Discard old batteries promptly in accordance with local laws and regulations.
• Always replace the entire set of batteries at one time.
• Never mix old and new batteries, or batteries of different brands or types.
mCAUTION
1. Plastic Parts: Wipe clean with mild soap and a damp cloth. Air dry.
2. Seat Pad: Machine wash in cold water in gentle cycle. DO NOT use harsh detergents or bleach.
DO NOT dry clean. Air or hang dry.
NOTE: To maintain stopping performance, clean friction strips regularly with damp cloth.
CARE & MAINTENANCE

4
Consumer Service: 1.800.453.7673
www.kolcraft.com
PARTS LIST
Seat Pad
Tray
Back Tires (2)
Tool Needed: Phillips screwdriver
Front Leg
Grill
Screws (4)
Front Casters (2)
Front Tires (2)
Sheet of Decals
Electronic Steering
Wheel
Steering Wheel
Locking Cup
Windshield Toy
Axles (2)Rear Wheels (2)
Hubcaps (4)
Base
Left Rear Leg Right Rear Leg Locking
Collar
Right Rear Leg Left Rear Leg Locking
Collar
Requires 2 AAA batteries (not included)

5
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Adhere the Decals
To Attach Grill to Tray
1Align the tabs of the grill with the slots on the front of the
walker and snap into place.
1
1Place the headlight and grill stickers from the decal sheet
as shown to the grill.
1

6
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Attach Legs to Tray
1Flip tray upside down, with the rear left tire well facing
you, marked with an “L”.
2Locate the left rear leg (as pictured) and place in the
groove on the left tire well.
3Locate the left rear leg locking collar. Align the L on the
lip of the collar with the L of the tray. Snap the collar
through the tray, securing the leg to the tray.
Repeat steps 2 & 3 for rear right leg.
4Locate the front leg and place it in the front leg groove as
shown, aligning the screw holes.
5Secure the front leg to the tray with screws in all four
places. Pull up on front leg to make sure the leg is
secure.
2
Left Rear
Leg
3
4
5

7
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Attach Tires to Tray
Left Right
1Snap 4 hubcaps into tires.
2Locate right back tire marked with an R. Fit tire into tire
well marked with an R. Tire should slide easily over leg
and securely snap into the tray. Repeat for other side.
3Locate 2 front tires. Align tire tabs with openings in tire
well and snap securely into tray. Repeat for other side.
2
3
1

8
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Attach Rear Wheels
1Flip base over to expose underside. Locate rear wheel
opening in base of the walker.
2Align holes of wheel with corresponding axle holes on the
base of the walker. Plastic tab may need to be pushed to
the side to expose the axle hole. The stem of the wheel
should be facing the inside of the base.
3Slide metal axle into holes from the inside towards the
outside of the base until the head of the axle passes the
plastic tab and the tab is able to hold the axle in place.
Repeat for other wheel.
Tab
Attach Front Casters
1Turn the base over and insert the stem of one of the front
casters into the hole in one of the front corners. Push
firmly until the caster snaps (locks) into place. Pull up on
caster to make sure it is locked in place.
CAUTION: Be sure the caster is inserted fully into the
base. The top lip of the caster threads should be flush
with the base hole. Nothing below this lip should be
visible.
Top Lip of
Caster Threads
Correct
Assembly
Incorrect
Assembly

9
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Attach Tray to Base
1Position assembled tray on top of base into appropriate
slots.
2Push rear leg tab in and snap into place. Repeat with
other rear leg.
3Snap front leg into place. Pull up on the tray to make sure
the tray and base are secure.
1
2
To Attach Windshield Toy
1Take the windshield toy and snap into place on top of
dashboard.
3

10
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Install Batteries in Electronic Steering Wheel
1To insert batteries, use a Phillips screwdriver to unfasten
battery cover located on the bottom of the electronic toy
steering wheel.
2Requires 2 “AAA” batteries (Not Included). Insert batteries
as shown. Secure battery cover.
3This toy has 2 levels of volume. Move switch to the
middle position for low volume and to the far right for
high volume. To turn off, move switch to “O” position.
3
2
To Attach Electronic Steering Wheel Toy
1Place the steering wheel toy into the hole on the
dashboard.
2Locate the steering wheel locking cup and snap over
bottom of steering wheel on underside of tray. Two tabs
will lock cup into place.
3To Replace Batteries and Remove the Steering Wheel Toy:
Push two tabs in and remove steering wheel locking cup.
Pull up on steering wheel toy to remove.
1
2

11
Consumer Service: 1.800.453.7673
www.kolcraft.com
To Attach Seat Pad to Tray
1Push crotch portion of the seat pad inside out to form
seat, so that the fabric is below the seat back.
2Place seat pad into seat ring located on tray. Align it so
that the highest point of the seat pad aligns with back of
walker ring.
3Insert the 4 tabs on the seat pad into slots located around
the front of the seat ring. Slide tabs through holes.
4Underneath the tray, pull tabs and align into grooves.
5Velcro the back of the seat pad around the rear of the seat
ring.
Test: Push down hard on seating area of seat pad to make
sure seat is securely in place.
CAUTION: Do not use walker if all tabs and Velcro are not
secured properly, otherwise child may fall through walker.
1
3
Tabs
4
Tabs
Grooves
5

12
To Convert to Walk-Behind Walker
1Remove the seat pad by unfastening the 4 seat tabs from
the tray and unsnapping the rear of the seat pad.
2Your child can now stand behind the walker, using the
texturized handle grip for support as they learn how to
walk in the walk-behind mode.
2
To Adjust Seat Pad Height
NOTE: As your child begins to grow, adjust height of walker via
the seat pad so that their feet touch the ground when seated.
To determine correct height after assembly, place child in
walker and make sure both feet touch the ground. Always make
sure seat pad is adjusted to the correct height position before
placing child in product.
1After seat pad is attached to tray, flip unit upside down to
access the restraint strap on underside of seat pad.
2Please note, to ensure proper operation, you will need to
periodically adjust the seat restraint to accommodate your
childs increased height. For smaller babies, seat pad
should be extended to its lowest position. To adjust seat
height, push button in on restraint strap to release
restraint.
3As baby grows, raise seat by tightening belt. This helps
to prevent the child from placing their feet flat on ground
and prevents your child from climbing out.
2
Please direct any comments, questions or replacement part requests to:
Kolcraft®Consumer Service Department
1100 W Monroe St. Chicago, IL 60607
1-800-453-7673 in U.S., 1-312-361-6315 outside U.S.
8 am-5 pm (CT) Monday - Thursday, 8 am - 3 pm Friday (CT)
e-mail: [email protected]