Kolpin Outdoors Throttle Master User manual
1
© 2022 Kolpin Outdoors Inc. REV 04
Throttle Master
Product Instructions | Part No: 98005
Item Qty Part Description
1 1Mounting Base
21Throttle Master
321/4” Truss Head Bolt
421/4” Lock Nut
52Rubber Cap
KIT CONTENTS:
APPLICATION: Verify accessory tment at Kolpin.com prior to installaon or usage.
BEFORE YOU BEGIN:
SAFETY INFORMATION:
WARNING
Failure to properly install or use Throle Master could result in serious injury or death. Use only with approved vehicle tment.
Verify up to date accessory instrucons, warnings, and tment at Kolpin.com prior to installaon or usage. Read and follow opera-
tor’s manual prior to installaon and usage. Make sure your vehicle is clean and free of debris prior to installaon.
WARNING
• Inspect Throle Master for damage. Do not use and replace if damage or wear does not allow for proper funconality. Be-
fore starng the ATV:
- Make sure Throle Master is ghtly secured on the OEM thumb throle.
- Make sure throle travels from no throle to full throle and full throle to no throle without interference
(minimum 1/8” clearance) from hand grips or other components / accessories. Repeat this check with the
handlebars in full le and full right posion.
• If the Throle Master is impacted by an object (tree branch, debris, etc.), nd a safe locaon to stop and assess the situaon.
Inspect the Throle Master for damage and funcon as menoned directly above prior to resuming riding.
• Do not modify the Throle Master. Only use included mounng hardware for installaon.
• Loose-ng riding gear, such as gloves and long-sleeve clothes, could interference with throle control. Do not use Throle
Master with riding gear that interferes with throle control. Always follow ATV manufacturer’s safety instrucons for proper
riding gear.
2
© 2022 Kolpin Outdoors Inc. REV 04
1. Conrm accessory tment at Kolpin.com to ensure this accessory is de-
signed to t your ATV.
2. Place the Throle Master over your exisng throle on your ATV.
3. Using the lock nuts, 1/4” truss head bolts, and a Phillips screw driver,
loosely ghten to hold the Throle Master on the ATV throle. See Illus-
traon 1-1.
4. Check the locaon of your new Throle Master. You can slide the
Throle Master Secon outwards to obtain more leverage.
5. Tighten down the Mounng Base securely to the ATV throle.
6. Place the Rubber Caps over the extra threads that protrude out past the
backside of the Mounng Base.
7. With the ATV o, check throle funcon to ensure 1/8”
minimum clearance with hand grips and any other
parts / accessories on the handle bars. Some hand grips
may need to be trimmed to ensure sucient clearance.
Trim the enre circumference so that the grip can rotate
without interfering with Throle Master. See Illustra-
on 1-2, 1-3, and 1-4. Adjust if needed.
WARNING! Do not use Throle Master if proper clearance cannot be achieved on
your ATV. Installing Throle Master without at least 1/8” clearance from all parts
for its enre range of moon could result in the throle being stuck in the open po-
sion, which may lead to loss of control, serious injury, or death. If throle becomes stuck in open posion while
operang, apply the brakes to come to a stop and turn o the ATV.
TOOLS REQUIRED:
• Phillips #2 screw driver
INSTALLATION INSTRUCTIONS:
One Year Limited Warranty
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found upon
examinaon by Kolpin to be defecve in material, workmanship, or both.
All transportaon costs incurred subming product to Kolpin for warranty consideraon must be borne by the purchaser. If Kolpin determines
that the product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorizaon (RMA) number
and shipping instrucons.
This warranty does not apply to parts that have been damaged by accident, alteraon, abuse, improper maintenance, normal wear, or other
causes beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or hardware are
designed to fail when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not covered under war-
ranty. This warranty does not cover removal or reinstallaon labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is general in
nature and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specicaon.
Ill 1-2
Ill 1-1
1/8” min clearance between
Throle Master and grip
Ill 1-3
• Trimming tool
Grip trimming
required
Ill 1-4
Trimmed
Unmodied
This manual suits for next models
1
Table of contents
