Kompernass KH 4056 User manual

Kompernaß GmbH · Burgstrasse 21 · D-44867 Bochum
ID-Nr.: KH4056_09/06_V1
www.kompernass.com
UK
KH4056_IB_UK 19.09.2006 14:23 Uhr Seite 1

KH 4056 Bicycle Hoist
Operating instructions
KH4056_IB_UK 19.09.2006 14:23 Uhr Seite 2

KH 4056
1







2
3
KH4056_IB_UK 19.09.2006 14:23 Uhr Seite 3

- 3 -
KH 4056

Bicycle Hoist KH 4056
Safety information
• Read the operating instructions care-
fully before using the appliance for
the first time and preserve this book-
let for later reference.
Pass the manual on to whomsoever
might acquire the appliance at a later
date.
• Never lift more than 20 kg with the
bicycle hoist. This would damage the
bicycle hoist and cause the load to
crash down.
• Check for the correct tightness of all
screws before using the bicycle hoist.
• At all times use the wall bracket for
securing the load. Otherwise, the load
could crash down.
• Do not take up a position underneath
the hanging load.
• Use the bicycle hoist for storage only,
not for any other purpose.
• Do not carry out repairs on the sus-
pended load.
• Should the nylon cord be damaged,
exchange it as soon as possible.
It could tear.
Attention Ensure that the nylon cord
does not slide too fast between your
hands! It could lead to burns and ab-
rasions!
Attention The bicycle hoist may not
be operated by weak people, for
example children. The bicycle could
crash down and cause injuries.
Intended use
The bicycle hoist is intended to save
space and relieve the tyres during bicycle
storage.
It is not meant to be used for commer-
cial purposes.
Delivery Contents
2 Ceiling brackets
2 Double retaining hooks
1 Nylon cord
1 Wall bracket for the nylon cord
10 Cross-head screws with plugs
Description of the appliance
Ceiling bracket
Nylon cord
Safety mechanism
Double retaining hooks
Cross-head screws
Plugs
Wall bracket
Required assembly tools:
1 Cross-head screwdriver
1 Measuring tape
1 Drill
1 Drill bit (8 mm diameter)
KH4056_IB_UK 19.09.2006 14:23 Uhr Seite 3

- 4 -
KH 4056

Assembly
The best assembly results are achieved
when the ceiling brackets are located
directly above the seat and handlebars.
Ensure there is sufficient clearance from
the side walls.
1. Measure the distance between the
handlebars and the seat on your
bicycle.
2. Transfer this measurement to the cei-
ling, marking the required drill-holes
with the aid of a ceiling bracket. Drill
the required holes and insert the
plugs.
3. Make a stable square knot at one end
of the nylon cord and thread it
through the rear ceiling bracket
(See Fig. 1).
4. Fasten both ceiling brackets to the
ceiling with the supplied cross-head
screws and plugs (see Fig. 1).
5. Connect the construction with the
cord in accordance with the block and
tackle principle. Run the cord through
the rollers in alternation, starting at
the ceiling bracket (see Fig. 3).
6. Run the cord through the safety
mechanism in the ceiling bracket.
(see Fig. 2).
7. Check that all screws are firmly tighte-
ned before using the bicycle hoist.
8. Assemble the wall mount. To do this,
lift the bicycle with the hoist and
mark the position for the wall mount.
9. After assembling the wall mount,
check all screw connections for tight-
ness again.
Notice: Should the cord slip quickly
through your hands when raising or
lowering the bicycle, the increased
tempo of the cord itself will trigger
the brake and the cord will stop auto-
matically.
Maintenance
Grease the rollers at regular intervals.
This will ensure that the bicycle hoist
moves easily.
Disposal
The packaging consists of 100% environ-
mentally friendly materials that can be
disposed of at local recycling collection
sites. Contact your municipal or commu-
nity administration for information on
disposal possibilities for metallic compo-
nents.
Importer
Kompernaß GmbH
Burgstrasse 21
D-44867 Bochum
www.kompernass.com
KH4056_IB_UK 19.09.2006 14:23 Uhr Seite 4