Konica Minolta bizhub 750 Instruction and safety manual

*9961060400*
*9961060400*
www.konicaminoltaeurope.com
Copyright
2005 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
Konica Minolta Business Solutions Europe GmbH
Europaallee 17
D-30855 Langenhagen
Phone [phone]
Fax [phone]
Printed in Germany
User Manual
750/600
User manual [Enlarge Display Operations]
750/600
Umschlag-O-Mat v1.4 | Vorlage: KM_Klebe_bizhub_9.indd (IDCS 3.01) | CL 040405Fonts: „HelveticaNeue KM Int“ (Bold+Regular) / „Code 39“ 29,8mm

.

bizhub 750/600 (Phase 2) Contents-1
Introduction
Thank you for choosing this machine.
The bizhub 750/600 User manual [Enlarge Display
Operations] contains details on the operation of the
various functions available in the Enlarge Display mode
of the bizhub 750/600 and on the various operating
precautions. In order to ensure that this machine is
used correctly and efficiently, carefully read the Enlarge
Display Mode Operations volume of the user manual
before using the machine.
After reading the Enlarge Display Mode Operations
volume of the user manual, store it in the designated
holder so that it can easily be referred to when
questions or problems arise during operation.
Views of the actual equipment may be slightly different
from the illustrations used in this Enlarge Display Mode
Operations volume of the user manual.

Contents-2 bizhub 750/600 (Phase 2)
Explanation of manual conventions
7 CAUTION
CAUTION
%Failure to observe instructions highlighted in this
manner may result in serious injuries or property
damage. Observe all cautions in order to ensure safe
use of this machine.
2
Reminder
Text highlighted in this manner indicates operation
precautions. Carefully read and observe this type of
information.
!Detail
Text highlighted in this manner provides more
detailed information concerning operating
procedures and other descriptions.
2
Note
Text highlighted in this manner indicates sections
containing additional information. If necessary, refer
to the indicated sections.

bizhub 750/600 (Phase 2) Contents-3
[ ]
Names highlighted as shown above indicate keys on
the control panel and buttons in the touch panel.

Contents-4 bizhub 750/600 (Phase 2)
Contents
1 Before making copies
1.1 Control panel parts and their
functions .................................................. 1-3
1.2 Adjusting the angle of the control
panel ......................................................... 1-7
1.3 Screens in Enlarge Display mode .......... 1-9
1.4 Touch panel ........................................... 1-11
Touch panel operation ......................... 1-11
Icons that appear in the screen ............ 1-12
Paper type icons .................................. 1-13
Paper supply icons ............................... 1-15
1.5 Feeding the original .............................. 1-16
1.6 Specifying original settings .................. 1-20
Selecting the original orientation
(“Original Direction” settings) ............... 1-23
Selecting the position of the binding
margin (“Margin” settings) .................... 1-26
2 Using copy functions
2.1 General copy operation .......................... 2-3
2.2 Selecting the density settings ................ 2-6
2.3 Selecting a Paper setting ..................... 2-11
2.4 Specifying a Zoom setting .................... 2-15
2.5 Selecting a Simplex/Duplex setting ..... 2-19

bizhub 750/600 (Phase 2) Contents-5
2.6 Selecting the quality of the original ......2-22
2.7 Selecting a Combine Originals setting 2-25
2.8 Selecting Finishing settings ..................2-27
2.9 Specifying Folding settings ...................2-32
2.10Selecting the Paper settings .................2-34
2.11Scanning the next original during
printing (reserving a copy job) ..............2-41
2.12Stopping scanning/printing ..................2-44
3 Using scan functions
3.1 General scan operation ...........................3-3
3.2 Specifying a recipient ..............................3-6
3.3 Specifying scanning settings
(Scan Settings) .......................................3-15
File Type ................................................3-15
Scan Size ..............................................3-21
Simplex/Duplex .....................................3-24
4 Using fax functions
4.1 General fax transmission operation .......4-3
4.2 Specifying a recipient ..............................4-6
4.3 Specifying the transmission settings
(Scan Setting) .........................................4-18
Original Image Type ..............................4-19

Contents-6 bizhub 750/600 (Phase 2)
5 Additional copy operations
5.1 When a login screen appears ................. 5-3
5.2 Checking the settings
(Mode Check) ......................................... 5-12
5.3 Printing a sample to check the
settings (Proof Copy) ............................ 5-16

1Before
making
copies

Before making copies 1
bizhub 750/600 (Phase 2) 1-3
1 Before making copies
1.1 Control panel parts and their
functions
2
Note
For details, refer to the User manual [Copy
Operations], User manual [Network Scanner
Operations], and the User manual [Facsimile
Operations].

1Before making copies
1-4 bizhub 750/600 (Phase 2)
No. Part name Description
1 [Power Save] key Press to enter Low Power mode.
While the machine is in Low Power
mode, the indicator on the [Power
Save] key lights up in green and the
touch panel goes off. To cancel Low
Power mode, press the [Power Save]
key again.
2 Touch panel Displays various screens and
messages.
Specify the various settings by
directly touching the panel.
3 [Access] key If user authentication or account track
settings have been applied, press this
key after entering the user name and
password (for user authentication) or
the account name and password (for
account track) in order to use this
machine.
4 [Fax] key Press to enter Fax mode. While the
machine is in Fax mode, the indicator
on the [Fax] key lights up in green.
5 [Scan] key Press to enter Scan mode. While the
machine is in Scan mode, the
indicator on the [Scan] key lights up in
green.
6 [Copy] key Press to enter Copy mode. (As a
default, the machine is in Copy mode.)
While the machine is in Copy mode,
the indicator on the [Copy] key lights
up in green.

Before making copies 1
bizhub 750/600 (Phase 2) 1-5
7 [Reset] key Press to clear all settings (except
programmed settings) entered in the
control panel and touch panel.
8 [Proof Copy] key Press to print a single proof copy to be
checked before printing a large
number of copies. (See p. 5-16.)
9 [Stop] key Pressing the [Stop] key during an
operation temporarily stops the
operation.
10 [Start] key Press to start an operation. When this
machine is ready to begin an
operation, the indicator on the [Start]
key lights up in green. If the indicator
on the [Start] key lights up in orange,
the operation cannot begin.
Press to restart a stopped job.
11 Main Power
indicator
Lights up in green when the machine
is turned on with the main power
switch.
12 Data indicator Flashes in green while a print job is
being received.
Lights up in green when a print job is
queued to be printed or while it is
being printed.
13 Keypad Use to type in the number of copies to
be produced.
Use to type in the zoom ratio.
Use to type in the various settings.
14 [C] (clear) key Press to erase a value (such as the
number of copies, a zoom ratio, or a
size) entered using the keypad.
No. Part name Description

1Before making copies
1-6 bizhub 750/600 (Phase 2)
15 [Mode Check]
key
Press to display screens showing the
specified settings.
16 [Utility/Counter]
key
Press to display the Meter Count
screen and the Utility screen.
17 Contrast dial Use to adjust the contrast of the touch
panel.
18 [Enlarge Display]
key
While the indicator on the [Copy],
[Scan], or [Fax] key is lit in green,
press to enter Enlarge Display mode.
19 [Accessibility] key Press to display the Accessibility
Setting screen.
No. Part name Description

Before making copies 1
bizhub 750/600 (Phase 2) 1-7
1.2 Adjusting the angle of the control
panel
The control panel can be adjusted to any of two angles.
Adjust the control panel to the angle that allows for
easy operation.
1 Upper position
(base position)
2 Lower position

1Before making copies
1-8 bizhub 750/600 (Phase 2)
To adjust the angle of the control panel
%Press the control panel
release lever, and then
push down on the
control panel.
Control panel
release lever

Before making copies 1
bizhub 750/600 (Phase 2) 1-9
1.3 Screens in Enlarge Display mode
To display the screens in Enlarge Display mode
1Press the [Copy], [Fax] or [Scan] key in the
control panel to display the desired screen.
2Press the [Enlarge
Display] key in the
control panel.
– Depending on the
settings specified in
the Accessibility
Setting screen, a
message appears, requesting confirmation to
return the settings to their defaults. For
details on specifying settings in the
Accessibility Setting screen, refer to the User
manual [Copy Operations].

1Before making copies
1-10 bizhub 750/600 (Phase 2)
The screen in the touch panel appears in
Enlarge Display mode. The screens can also be
changed by pressing the [Copy], [Fax] or [Scan]
key while the screens are displayed in Enlarge
Display mode.
3To return to the standard-sized screens to the
screens in Enlarge Display mode, press the
[Enlarge Display] key in the control panel.
– Depending on the settings specified in the
Accessibility Setting screen, a message
appears, requesting confirmation to return
the settings to their defaults.

Before making copies 1
bizhub 750/600 (Phase 2) 1-11
1.4 Touch panel
Touch panel operation
To activate a function or to select a setting, lightly
touch the button in the touch panel for the desired
function or setting.
2
Reminder
Do not apply extreme pressure to the touch panel,
otherwise it may be scratched or damaged. Never
push down on the touch panel with force, and never
use a hard or pointed object to make a selection in
the touch panel.

1Before making copies
1-12 bizhub 750/600 (Phase 2)
Icons that appear in the screen
Icon Description
This button appears when there is a
message indicating that a print error
occurred. Touch this button to display the
message, and then perform the necessary
steps.
Touch this button to display the message in
Enlarge Display mode.
Touch this button to return the message to
its standard size from Enlarge Display mode.
This icon appears when the toner has run
out, and copies can no longer be made and
faxes can no longer be received. Replace the
toner cartridge.