Konica Minolta bizhub C203 Series User manual

© 2016 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub
132360
Konica Minolta Kit - Bizhub
132360
Product Version: 360 ~ 420 ~ 500
Version of this manual: 2.2.20
Inepro Kit number: 132360
Konica Kit number: 9967000514

Version 2.2.20 Inepro B.V. http://www.inepro.com
Table of Contents
Introduction 2
Check Kit Content 4
Hardware Setup 12
........................................................................................................................................................ 121Attach the PayCon to the bracket
........................................................................................................................................................ 132Attach the bracket to the copier
Set up the copier 22
........................................................................................................................................................ 221Konica Minolta Bizhub Colour V3
Set up the PayCon 26
........................................................................................................................................................ 261 Behaviour
........................................................................................................................................................ 272 Network
........................................................................................................................................................ 283 General Settings
Notes 32

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub 132360
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
-Bizhub C203
-Bizhub C253
-Bizhub C353
-Bizhub C451
-Bizhub C550
-Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub 132360
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub colour V3
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub Colour V3
In the "KM Mounting kit for Bizhub Colour V3" you should find:
·1x PayCon copier mounting bracket
·1x KM cableset Minolta Serial I/F - V3
·1x KM screwset Bizhub V3 C550
·1x KM Mounting plate Bizhub Colour - V3
·1x This manual
·1x 150cm Black cat 5 network cable

Version 2.2.20 - 5
KM Screwset Bizhub Colour V3 C550
KM Screwset Bizhub Colour V3 C550
In the "KM Screwset Bizhub Colour V3 C550" you should find:
·3x M4 x 5mm Dome shaped, cross head screws
·1x M4 x 12mm Dome shaped, cross head screw
·1x M4 x 16mm Dome shaped, cross head screw
·2x M3 x 12mm Dome shaped, cross head screws
·1x M3 x 16mm Dome shaped, cross head screw
·1x M3 x 16mm Dome shaped, countersunk cross head screw
·2x M3 x 20mm Dome shaped, cross head screws
·1x M3 Star lock washer
·4x M4 Star lock washers
·2x M3 x 5mm spacer
·1x M3 x 15mm spacer
·1x M4 x 5mm spacer
·1x M4 x 12mm spacer
·4x M3 Black nylon cable guiders
·1x M4 Black nylon cable guider
·5x Rip Ties
·1x 84cm x 15mm Black slit wrap harness (the black hose)

6 - Konica Minolta Kit - Bizhub 132360
Check Kit Content
KM Mounting plate Bizhub Colour V3
KM Mounting plate Bizhub Colour V3
1x KM mounting plate Bizhub Colour V3

Version 2.2.20 - 7
KM Cableset Minolta serial I/F V3

8 - Konica Minolta Kit - Bizhub 132360
Check Kit Content
KM Cableset Minolta serial I/F V3
In the "KM Cableset Minolta serial I/F V3" you should find:
·3x Rip ties
·1x Ferrite core
·1x Connection cable
·1x Double sided adhesive tape 25mm x 30mm
·1x Connector block male/male

Version 2.2.20 - 9
PayCon copier mounting bracket
PayCon copier mounting bracket
In the "PayCon copier mounting bracket" you should find:
·1x PayCon copier mounting bracket
·4x Dome shaped, cross head screws
·3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
·PayCon Copy
·2x CAT-5 Network cables (one cable included)

Hardware Setup
Part
III

12 - Konica Minolta Kit - Bizhub 132360
Hardware Setup
Hardware Setup
Additional requirements:
·Pair of wire cutters
·No. 2 cross head screwdriver
·No. 1 PosiDriv head screwdriver
·PayCon Copy
·2x CAT-5 Network cables (one cable included)
Recommend Tools:
·SHR Slit Wrap Tool, Richco part nr. CAT-15-PP (for guiding cables into the slit harness wrap)
Attach the PayCon to the PayCon bracket
1. Break out the appropriate gaps in the flaps
2. Close the two left flaps and fasten the middle one with it's screw. Feed the wires through the bracket and connect the power supply to
the socket bottom-left to the 'Opto COM 12' and the copier cable to 'Opto COM 12' as shown in the picture

Version 2.2.20 - 13
Attach the PayCon to the bracket
3. Use the rip tie to attach the power cable and connection cable to the flap, thus creating a cable relief, and clip the rip tie using the wire
cutter
4. Close and gently screw down the last flap and place the PayCon bracket on the PayCon with the screws from the bracket kit
5. Place the ferrite cores and loop the network cables through them once
Attach the PayCon bracket to the copier
The mounting instructions differ for the different type of copiers its supports. The instructions for each part will start with
the list of copiers that the instructions are meant for.
-Bizhub C203
-Bizhub C253
-Bizhub C353

14 - Konica Minolta Kit - Bizhub 132360
Hardware Setup
1. Screw off the copier flap and open the scanner top to lift the flap out, and remove the backside flap as well.
2. Attach the cable with the 2 rip ties to the existing cable , as shown above. Make sure you do not allow the cable to be too long because
then it will hinder the door. Feed the cable to the backside of the copier through the inside.
3. Screw on the mounting plate. Screw on the two cable guiders with the spacers and screws. Screw down the rest of the cover with the
original cover screws.

Version 2.2.20 - 15
Attach the bracket to the copier
4. Screw on the PayCon with the 3 screws.
5. Loop the wire trough the ferrite core you will attach the the top, and use the existing cable guiders to guide the wire trough
6. Connect the copy cable and close the back and side flap. Guide the cables in the slit wrap harnas and attach it to the cable guide with
the rip ties. Connect the network cable to the socket hidden behind the corner flap
7. Remove the transport foils to finish the installation

16 - Konica Minolta Kit - Bizhub 132360
Hardware Setup
8. Finished