Konig VID-TRANS150KN User manual

www.konigelectronic.info
VID-TRANS150KN
2.4GHz WIRELESS AUDIO/VIDEO
TRANSMISSION SYSTEM
MANUAL
PATENT
0336
ENGLISH

Important Safety Precautions
This equipment generates and uses radio frequency energy and if not
installed and used properly, that is in strict accordance with the
manufacture's instructions, may cause interference to radio and television
reception. It has been tested and found to comply with the provisions of the
1999/5/EC R&TTE directive, which are designed to provide reasonable
protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient the TV/radio antenna.
2. Relocate the Receiver away from the TV/radio receiver.
3. Plug the Receiver into a different wall outlet so that the Receiver is on a
different branch circuit.
4. If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions.
The user is warned that changes or modifications not approved by the
manufacturer could void the user's authority to operate the equipment.
Linear radio controls provide a reliable communications link and fill an
important need in portable wireless signaling. However, there are some
limitations which must be observed.
The equipment is required to comply with the provisions of the 1999/5/EC
R&TTE directive. As such, they have limited transmitter power and
therefore limited range. A receiver cannot respond to more than one
transmitted signal at a time and may be blocked by radio signals that occur
on or near their operating frequencies. Changes or modifications to the
device may void R&TTE compliance.
1
A. Contents of the packaging:
1. Transmitter ×1
2. Receiver ×1
3. Power adapter ！×2
230VAC to 7.5VDC
300mA
4. IR extender with 2,5mm plug ×1
For transmitter
5. IR extender with 3,5mm plug ×1
For receiver
2

B. Introduction:
This 2.4GHz system is a wireless audio/video transmission system that
uses advanced wireless communication technology to deliver consistently
sharp audio and video up to 80 meters in open area and 30 meters trough
walls and ceilings (depending on environment circumstances). The PLL
circuit controls the strength and quality of the signal by locking it. It also
integrates an UHF remote control extender to allow you to control the audio
or video source from another room using your existing remote controller.
Using this system, you can enjoy greater convenience of audio/video
equipment in many ways.
C. Product description:
FRONT VIEW TRANSMITTER
3
REAR VIEW TRANSMITTER
FRONT VIEW RECEIVER
Channel select CH3
or CH4 (NTSC only)
RF output to TV
(e.g.2058R)
4
Channel selection switch.
Select same channel
on transmitter and
receiver
Power indicator
Power on/off switch
IR extender emits infrared
signals and control the source
A/V equipment.
IR extender port IR extender emits infrared
signals and control the source
A/V equipment. Channel selection switch.
Select same channel
on transmitter and
receiver
Power indicator
Power on/off switch
IR extender port
Input SCART port
Plug into the AV output port of DVD
or VCR or SAT etc.
DC power input
connect to power
adapter (7.5V DC)
DC power input
connect to power
adapter (7.5V DC)

REAR VIEW RECEIVER
D. Installation overview:
5
Installation of the 2.4GHz transmitter and receiver:
1.Plug the transmitter into the SCART output port of VCR, DVD or SAT.
2.Plug the receiver into the SCART input of the LCD screen, PLASMA
screen or television.
3.Put the plug of the power adapter into the transmitter and the receiver
and the power plug into the 230-volt wall outlet. Note: use only the
provided adapters.
4.Select the desired channel with a combination of the switches (see
below figure) If a channel gives some distortion in picture and sound try
another combination of the switches.
E. Using the remote control feature:
The 2.4GHz system not only allows you to send audio/video from one area
to another, it also gives you the ability to control the source using your
existing remote control device. It converts the infrared (IR) signal emitted
by your remote control to a radio frequency (RF) signal in UHF band at the
receiver and sends it back to the transmitter where the RF signal is
converted back to the original IR signal and beamed to the audio/video
source.
Use the IR cable and connect the 2.5mm plug to the input jack on the back
of the transmitter (IR-T). Place the IR sensor on the front of the display
from the equipment that need to be controled. It’s important to place the IR
sensor as close as possible to the IR sensor, which is behind the display,
of the equipment. If this function is not working correctly, check this
accurate. (see figure next page)
6
Plug into the A/V input port of
TV, MONITOR, etc.
Output SCART port
Wal
l
Mounting
Holder
IR Ex ten de r
Mouse
IR Ex ten de r
Mouse
(Not Inc luded)
Scart Plug toJack Cable
IR
Remote
Control
433.92MHz IR Remote Signal
2.4GHz (Video, Audio)
RX
Wal
l Mounting 42" TFT Monitor
IR
Sensor
Audio Sources:
Compact Disk Player
Stereo Receiver
Cassette Deck
DVD
VCR
SAT Receiver
Laser Disc Player
Camcorder
Video Sources:
ROOM 1 ROOM 2
ROOM 2ROOM 1
433.92MHz IR Remote Signal
433.92MHz IR Remote Signal
IR
Extender
Mouse
2. Operation:
1. Installation:
Application:
2.4GHz (Video,Audio)
2.4GHz (Video, Audio)
SAT
Receiver
DVD
TX
SAT
Receiver
DVD
TX
IR
Remote
Control
IR
Remote
Control
RX
RX
RX
RX
Desktop 42" TFT Monitor
WallMounting 42" TFT Monitor
Wal
l Mounting 42" TFT Monitor
Desktop 42" TFT Monitor

Use the IR cable and connect the 3.5mm plug to the input jack on the back
of the receiver (IR-R). Place the IR sensor in front of the equipment. For
receiving the infrared signals of the remote control it’s important the sensor
is placed in sight.
F. Troubleshooting, Care and maintenance:
Problem Possible solutions
No picture or sound
Check all connections.
Make sure power plugs are pushed all the way in.
Check the power switches of the connected
equipment
Check the power on/off switches on the
transmitter and receiver.
Interference:
Noisy picture or audio
Select a different channel by pushing the channel
selector button on both transmitter and receiver
so that the channels match.
If using a microwave oven, turn it off.
Remove microwave oven from path between
transmitter and receiver.
Remote control
extender does
not work
Check the path between the transmitter and the
audio/video source and clear any obstructions.
Check if the batteries from the remote control are
full.
Make sure IR extender is properly located on the
A/V equipment you wish to control.
7
G. Specifications:
Transmitter:
Operating Frequency Band 2.400GHz~2.4835GHz
Maximum Output Level 10dBm (CE)
Modulation FM (video and audio)
Channels (4) PLL frequency synthesizer
Video Input Level 1V p-p @ 75 ohm
Audio Input Level 1V p-p @ 600 ohm (STEREO)
Input Port SCART socket
Antenna Hidden omni-directional
IR–remote IR output 940nm with ON/OFF keying
Power 7.5VDC,150mA
Dimensions 100mm×60mm×22mm
Weight 100gr.
Receiver:
Operating Frequency Band 2.400GHz~2.4835GHz
Sensitivity -80dBm minimum
Channels (4) PLL frequency synthesizer
Video Output Level 1V p-p @ 75 ohm
Audio Output Level 1V p-p@ 600 ohm (STEREO)
Output Port SCART socket
Antenna Hidden omni-directional
Transmit Frequency 433.92 MHz
IR remote modulation ASK
Infrared Freqeuncy Input 35 KHz~41 KHz
Power 7.5 VDC, 230mA
Dimensions 100mm×60mm×22mm
Weight 110gr.
System:
Operational range up to 80 meter (line of sight)
Remote control range up to 50 meter (line of sight)
Operating temperature 10°C ~ 50°C (14 F ~ 122 F)
*Actual range depends on environment circumstances.
All specifications subject to change without prior notice
8
IR sensor in front of display
VCR, DVD, SAT or other

DECLARATION OF CONFIRMITY
We,
Nedis B.V.
De Tweeling 28
5215MC ’s-Hertogenbosch
The Netherlands
Tel.: [phone]
Fax.: [phone]
Email: [e-mail]
Internet: www.nedis.com
Declare under our responsibility that the product;
Brandname: König
Model: VID-TRANS150KN
Description: 2.4GHz wireless transmission system
Is in confirmity with the following standards;
Radio: EN 300-220-3 (2000-09); EN 300 440 (1999-04)
EMC: EN 301 489 (2002-08)
LVD: EN 60065: 1998
Following the provisions of the 1999/5/EC R&TTE Directive.
Conform this regulation it’s allowed to use this product in
all European Community & EFTA countries.
Nedis BV is not responsible for the use of this product outside
the European Community & EFTA countries.
‘s-Hertogenbosch, 16-08-2005
Mrs. J. Gilad
Purchase Director
9