Kontron Ktus15/mitx 1.6ghz std User manual

If it’s embedded

it’s Kontron.

KTUS15/mITX Users Guide

KTD-00774-D

KTD-00774-D KTUS15/mITX Page 2 of 82

www.kontron.com

Document revision history.

Revision Date By Comment

D Jan. 12th 2010 MLA

RAID info corrected. Info on max video memory added. Wake on USB

support corrected. PWR_OK on Feature connector corrected to

POWER_UP and related info corrected. Added OS support. Feature

connector pin 4 corrected to PSUP_OFF signal.

C Oct. 13th 2009 MLA Added “mounting the board to chassis”. Minor changes.

B Sep. 22nd 2009 MLA Added SDRAM PN available. Minor changes. Improved drawings.

A Jun. 19th 2009 MLA First complete version

0 May 27th 2009 MLA Initial release

No part of this document may be reproduced or transmitted in any form or by any means, electronically or

mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.

Trademark Acknowledgement:

Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer:

KONTRON Technology A/S reserves the right to make changes, without notice, to any product, including

circuits and/or software described or contained in this manual in order to improve design and/or

performance.

Specifications listed in this manual are subject to change without notice. KONTRON Technology assumes no

responsibility or liability for the use of the described product(s), conveys no license or title under any patent,

products are free from patent, copyright, or mask work right infringement, unless otherwise specified.

Applications that are described in this manual are for illustration purposes only. KONTRON Technology A/S

makes no representation or warranty that such application will be suitable for the specified use without

further testing or modification.

KTD-00774-D KTUS15/mITX Page 3 of 82

www.kontron.com

Life Support Policy

KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE

SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL

MANAGER OF KONTRON Technology A/S.

As used herein:

Life support devices or systems are devices or systems which, (a) are intended for surgical implant into

body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with

instructions for use provided in the labelling, can be reasonably expected to result in significant injury to the

user.

A critical component is any component of a life support device or system whose failure to perform can be

reasonably expected to cause the failure of the life support device or system, or to affect its safety or

effectiveness.

KONTRON Technology Technical Support and Services

If you have questions about installing or using your KONTRON Technology Product, check this User’s

Manual first – you will find answers to most questions here. To obtain support, please contact your local

Distributor or Field Application Engineer (FAE).

Before Contacting Support: Please be prepared to provide as much information as possible:

1. CPU Board

1. Type.

2. Part Number (find PN on label)

3. Serial Number if available (find SN on label)

2. Configuration

1. DRAM Type and Size.

2. BIOS Revision (Find the Version Info in the BIOS Setup).

3. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section).

3. System

1. O/S Make and Version.

2. Driver Version numbers (Graphics, Network, and Audio).

3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.

KTD-00774-D KTUS15/mITX Page 4 of 82

www.kontron.com

» Table of Contents «

1Introduction....................................................................................... 7

2Installation procedure ....................................................................... 8

2.1 Installing the board........................................................................................................................ 8

2.2 Requirement according to EN60950............................................................................................. 9

3System specification ....................................................................... 10

3.1 Component main data................................................................................................................. 10

3.2 System overview......................................................................................................................... 13

3.3 KTUS15/mITX Board configurations........................................................................................... 14

3.4 System Memory support ............................................................................................................. 15

3.5 KTUS15 Graphics Subsystem .................................................................................................... 16

3.5.1 Intel® Graphics Media Accelerator 500..................................................................................... 16

3.5.2 Dual Independent/Mirror/Single Display support....................................................................... 17

3.6 KTUS15 Power ........................................................................................................................... 18

3.6.1 Power Budget ............................................................................................................................ 18

3.6.2 Power Consumption .................................................................................................................. 18

3.7 KTUS15 Clock Distribution ......................................................................................................... 19

4Connector Definitions ..................................................................... 20

4.1 Connector layout......................................................................................................................... 21

4.1.1 KTUS15/mITX – Top side..........................................................................................................21

4.1.2 KTUS15/mITX - IO Bracket side................................................................................................ 22

4.1.3 KTUS15/mITX – Back side........................................................................................................ 22

4.2 Power Connector (PWR) ............................................................................................................ 23

4.3 Power Out Connector (PWR-OUT)............................................................................................. 24

4.4 Keyboard and Mouse connectors ............................................................................................... 25

4.4.1 MINI-DIN Keyboard and Mouse Connector (KBD).................................................................... 25

4.4.2 Keyboard and Mouse pinrow Connector (KBDMSE) ................................................................ 25

4.5 Display connector........................................................................................................................ 26

4.5.1 DVI Connector (DVI-A), Analogue output.................................................................................. 26

4.5.2 DVI Connector (DVI-D), Digital output....................................................................................... 27

4.5.3 LVDS Flat Panel Connector (LVDS).......................................................................................... 28

4.6 PCI-Express connectors ............................................................................................................. 29

4.6.1 PCI-Express x1 Connector (PCIe x1 Slot 1 and Slot 2) ............................................................ 29

KTD-00774-D KTUS15/mITX Page 5 of 82

www.kontron.com

4.7 Serial ATA Hard Disk interface ................................................................................................... 30

4.7.1 SATA Hard Disk Connector (SATA0, SATA1)........................................................................... 30

4.8 Parallel ATA Hard Disk interface ................................................................................................31

4.8.1 IDE Hard Disk Connector (PATA) ............................................................................................. 32

4.8.2 Compact Flash Connector (CF)................................................................................................. 33

4.9 Printer Port Connector (PRINTER) ............................................................................................. 34

4.10 Serial Ports.................................................................................................................................. 35

4.10.1 COM1, COM2, COM3 and COM4 Pin Header Connectors ...................................................... 35

4.11 Ethernet Connectors ................................................................................................................... 36

4.11.1 Ethernet Connector (LAN) ......................................................................................................... 36

4.12 USB Connectors (USB) .............................................................................................................. 37

4.12.1 USB Connector 0/2 (USB0/2).................................................................................................... 38

4.12.2 USB Connector 4/5 (USB4/5).................................................................................................... 38

4.12.3 USB Connector 6/7 (USB6/7).................................................................................................... 39

4.13 Audio Connectors........................................................................................................................ 40

4.13.1 Audio Line-In, Line-Out and Microphone................................................................................... 40

4.13.2 CDROM Audio Input (CDROM) ................................................................................................. 40

4.13.3 Audio Header (AUDIO_HEAD).................................................................................................. 41

4.14 Fan Connector (FAN_CPU) ........................................................................................................ 42

4.15 Boot ROM Selection Jumper (BOOT ROM) ............................................................................... 43

4.16 Clear CMOS Jumper (Clr-CMOS)............................................................................................... 43

4.17 TPM Connector (TPM)................................................................................................................ 44

4.18 Front Panel Connector (FRONTPNL)......................................................................................... 45

4.19 Feature Connector (FEATURE).................................................................................................. 46

4.20 PCI Slot Connector (PCI Slot)..................................................................................................... 47

4.20.1 Signal Description – PCI Slot Connector................................................................................... 48

4.20.2 KTUS15 PCI IRQ & INT routing ................................................................................................ 49

5Onboard connectors and Mating connectors.................................. 50

6System Resources.......................................................................... 51

6.1 Memory Map ............................................................................................................................... 51

6.2 PCI Devices ................................................................................................................................ 52

6.3 Interrupt Usage ........................................................................................................................... 53

6.4 IO Map ........................................................................................................................................ 54

Overview of BIOS Features ................................................................... 55

KTD-00774-D KTUS15/mITX Page 6 of 82

www.kontron.com

6.5 System Management BIOS (SMBIOS/DMI) ............................................................................... 55

6.6 Legacy USB Support .................................................................................................................. 55

7BIOS Configuration/Setup .............................................................. 56

7.1 Introduction ................................................................................................................................. 56

7.2 Main Menu .................................................................................................................................. 56

7.3 Advanced Menu .......................................................................................................................... 57

7.3.1 Advanced settings – CPU Configuration ................................................................................... 58

7.3.2 Advanced settings – IDE Configuration..................................................................................... 59

7.3.3 Advanced settings – LAN Configuration.................................................................................... 61

7.3.4 Advanced settings – Configure Win627DHG Super IO Chipset................................................ 62

7.3.5 Advanced settings – Hardware Health Configuration................................................................ 64

7.3.6 Advanced settings – Voltage Monitor ........................................................................................ 65

7.3.7 Advanced settings – ACPI Settings........................................................................................... 66

7.3.8 Advanced settings – PCI Express Configuration....................................................................... 67

7.3.9 Advanced settings – Smbios Configuration............................................................................... 67

7.3.10 Advanced settings – Trusted Support ....................................................................................... 68

7.3.11 Advanced settings – USB Configuration ................................................................................... 69

7.3.12 Advanced settings – USB Mass Storage Device Configuration ................................................ 70

7.3.13 Advanced settings – Spread Spectrum Clock ........................................................................... 70

7.4 PCIPnP Menu ............................................................................................................................. 71

7.5 Boot Menu................................................................................................................................... 72

7.5.1 Boot – Boot Settings Configuration ........................................................................................... 73

7.5.2 Boot – Boot Device Priority........................................................................................................ 74

7.6 Security Menu ............................................................................................................................. 75

7.7 Chipset Menu .............................................................................................................................. 77

7.7.1 Advanced Chipset Settings – North Bridge Chipset Configuration ........................................... 77

7.7.2 Advanced Chipset … – North Bridge … – Boot Display Configuration ..................................... 78

7.7.3 Advanced Chipset Settings – South Bridge Chipset Configuration........................................... 79

7.8 Exit Menu .................................................................................................................................... 80

8AMI BIOS Beep Codes ................................................................... 81

9OS Setup ........................................................................................ 82

10 Warranty ......................................................................................... 82

KTD-00774-D KTUS15/mITX Page 7 of 82

www.kontron.com

1 Introduction

This manual describes the KTUS15/mITX family of boards made by KONTRON Technology A/S.

All boards have included Intel Atom Processors (BGA) processors, either 1.1GHz or 1.6GHz Ultra Low

Power, depending on actual board configuration. The Intel® US15W chipset is used on all configurations.

Available configurations are:

KTUS15 configuration HT 1GBE PCI SATA TPM COM ports DVI CRT

KTUS15/mITX 1.1GHz Basic + 2 +

KTUS15/mITX 1.1GHz Std + + + 4 +

KTUS15/mITX 1.6GHz Std + + + + 2 +

KTUS15/mITX 1.6GHz Plus + + + + + 4 +

Use of this manual implies a basic knowledge of PC-AT hardware and software. This manual is focused on

describing the KTUS15 board’s special features and is not intended to be a standard PC-AT textbook.

New users are recommended to study the short installation procedure stated in chapter 2 before switching-

on the power.

All configuration and setup of the CPU board is either done automatically or by the user in the CMOS setup

menus. Except for the CMOS Clear jumper and the Boot BIOS ROM Selection jumper, no jumper

configuration is required.

KTD-00774-D KTUS15/mITX Page 8 of 82

www.kontron.com

Warning: When mounting the board to chassis etc. please notice that the board contains

components on both sides of the PCB which can easily be damaged if board is handled

without reasonable care. A dama

ed com

onent can result in malfunction or no function at all.

2 Installation procedure

2.1 Installing the board

To get the board running, follow these steps. In some cases the board shipped from KONTRON Technology

has DDR2 DRAM mounted. In this case Step 2 can be skipped.

1. Turn off the PSU (power supply unit)

2. Insert the DDR2 SODIMM 200pin DRAM module

See guidelines below for assembling / disassembling memory module.

For a list of approved DDR2 DIMM modules contact your Distributor or FAE.

DDR2-400 and DDR2-533 SODIMM 200pin DRAM modules (PC3200, PC4200) are supported.

3. Connect Interfaces

Insert all external cables for hard disk, keyboard etc. A CRT or DVI monitor (depending on actual

KTUS15 version) must be connected in order to change CMOS settings for flat panel support.

4. Connect the PSU and turn on the power to the PSU

Connect power supply to the board by the 6x2pin PWR connector.

Note: the board is a single-supply board, accepting input voltages from 5V to 25V (DC). Power cables for

connecting the KTUS15 family boards to a ATX power supply (+5V or +12V) are available from Kontron

(P/N 1022-6309).

5. Power Button

The PWRBTN_IN may be required to start the board; this is done by momentarily connecting together pins

16 (PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector description), to provide

a pulse on the PWRBTN_IN pin. A “normally open” switch can be connected via the FRONTPNL

connector.

6. BIOS Setup

Enter the BIOS setup by pressing the <Del> key during boot up. Refer to the “BIOS Configuration / Setup“

section of this manual for details on BIOS setup.

7. Mounting the board to chassis

When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and

having diameter of ~7mm.

Note: Do not use washers with teeth, as they can damage the PCB mounting hole and may cause short

circuits.

Note: To clear all CMOS settings, including Password protection, move the Clr-CMOS jumper (with or

without power) for approximately 1 minute. This will also disable any Secure CMOS setup on the board.

Alternatively, turn off power and remove the battery for 1 minute, but be careful to orientate the battery

correctl

when reinserted.

KTD-00774-D KTUS15/mITX Page 9 of 82

www.kontron.com

2.2 Requirement according to EN60950

Users of KTUS15 family boards should take care when designing chassis interface connectors in order to

fulfill the EN60950 standard:

Lithium Battery precautions:

CAUTION!

Danger of explosion if battery is incorrectly

replaced.

Replace only with same or equivalent type

recommended by manufacturer.

Dispose of used batteries according

to the manufacturer’s instructions.

VORSICHT!

Explosionsgefahr bei unsachgemäßem Austausch

der Batterie.

Ersatz nur durch den selben oder einen vom

Hersteller empfohlenen gleichwertigen Typ.

Entsorgung gebrauchter Batterien nach

Angaben des Herstellers.

ADVARSEL!

Lithiumbatteri – Eksplosionsfare ved fejlagtig

håndtering.

Udskiftning må kun ske med batteri

af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

ADVARSEL

Eksplosjonsfare ved feilaktig skifte av batteri.

Benytt samme batteritype eller en tilsvarende

type anbefalt av apparatfabrikanten.

Brukte batterier kasseres i henhold til fabrikantens

instruksjoner.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti

asennettu.

Vaihda paristo ainoastaan laltevalmistajan

suosittelemaan

tyyppiln. Hävitä käytetty paristo valmistajan

ohjeiden

mukaisesti.

When an interface/connector has a VCC (or other power) pin, which is directly connected to a power

plane like the VCC plane:

To protect the external power lines of the peripheral devices, the customer has to take care about:

•That the wires have suitable rating to withstand the maximum available power.

•That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC/EN 60950.

KTD-00774-D KTUS15/mITX Page 10 of 82

www.kontron.com

3 System specification

3.1 Component main data

The table below summarizes the features of the KTUS15/mITX embedded motherboards.

Form factor KTUS15/mITX: mini ITX (170.18millimeters by 170.18millimeters)

Processor

•Intel® Atom™ BGA processors 1.1GHz (Z510) or 1.6GHz (Z530) depending on board

configuration.

•On die, primary 32kB instructions cache, 24kB write-back data cache, and 512kB, 8-

way L2 cache.

•533MHz (Z530) / 400MHz (Z510) Source-Synchronous front side bus speed (FSB)

•Supports Hyper-Threading Technology 2-threads (Z530 only)

•Supports C0/C1(e)/C2(e)/C4(e) and Intel® Deep Power-Down Technology (C6)

•Thermal Design Power (TDP) of 2W for Intel® Atom™ processors Z510 and Z530

Memory

•DDR2 SODIMM 200pin DRAM socket

•Supports 1.8V DDR2 SDRAM

•Supports 400MT/s (Mega Transfer per second) and 533MT/s data rates

•Support system memory from 512MB and up to 2GB

•ECC not supported

Chipset •Intel® System Controller Hub US15W

Video

•Intel® Graphics Media Accelerator 500

•Ultra Low Power Integrated 3D Graphics core

•Graphics controller core frequency of 200MHz

•Full hardware acceleration of video decode standards, such as H.264, MPEG2,

MPEG4, VC1, and WMV9

•Video memory up to 256MB (Dynamic Video Memory). (Only up to 8MB can be

reserved in BIOS).

•Analog Display CRT output (depending on configuration) with support for analogue

monitors up to 1600x1200 at 60Hz.

•Digital Visual Interface digital output (DVI-D) (depending on configuration) with

support for digital monitors up to 1600x1200 at 60Hz.

•Single channel 18/24bit LVDS panel support (OpenLDI/ SPWG) up to Wide XGA

(1366x768 @ 85Hz) panel resolution. With external 1-to-2 pixel per clock converter,

LVDS panels up to 1280x1024 are supported.

•Dual independent pipe support, Mirror and Dual independent display support.

Audio

Audio, 7.1 and 7.2 Channel High Definition Audio Codec using the Realtek ALC888 codec

•Line-out

•Line-in

•Surround output: SIDE, LFE, CEN, BACK and FRONT

•Microphone: MIC1, MIC2

•CDROM in

•SPDIF Interface

Onboard speaker

(Continues)

KTD-00774-D KTUS15/mITX Page 11 of 82

www.kontron.com

I/O Control Winbond W83627DHG LPC Bus I/O Controller

Peripheral

interfaces

•Four USB 2.0 ports on I/O area

•Four USB 2.0 ports on internal pinrows

•Two / Four Serial ports (RS232C) (depending on board configuration)

•One Parallel port, SPP/EPP/ECP

•Two Serial ATA-150/300 IDE AHCI (depending on board configuration) w. RAID

support.

•One PATA 33/66/100 interface with support for 2 devices

•CF (Compact Flash) interface supporting CF type I and II. (UDMA2 max.). Note that

only one PATA device is supported when CF is used and only by use of 40-wire cable

(not 80-wire cable). Optionally, use SATA devices.

•PS/2 keyboard and mouse ports

LAN

Support •10/100/1000Mbits/s LAN using Intel ® 82574L controllers

•RPL/PXE netboot supported. Wake On LAN (WOL) supported (S3 only).

BIOS

•Kontron Technology / AMI BIOS (core version 8.00)

•Support for Advanced Configuration and Power Interface (ACPI 3.0), Plug and Play

oSuspend To Ram

oSuspend To Disk

oIntel Speed Step

•Secure CMOS/ OEM Setup Defaults

•“Always On” BIOS power setting

•System Locked Pre-Activation (SLP) key support

•Boot-Logo / Long splash support

•Setup for Forced Boot device

•Desktop Management Interface (DMI) with user-configurable setup

•TPM version 1.2 support

Expansion

Capabilities

•PCI Bus routed to 1 PCI slot (PCI Local Bus Specification Revision 2.3)

•PCI-Express bus routed to 2 (x1)PCI Express slots (PCI Express 1.0a)

•Two Secure Digital I/O (SDIO) card slots (backside)

•SMBus routed to TPM header, Feature connector, PCI, and PCI Express Slot

connectors

•LPC Bus routed to TPM connector

•DDC Bus routed to LVDS and CRT /DVI connector

•8 x GPIOs (General Purpose I/Os) routed to FEATURE connector

Hardware

Monitor

Subsystem

•Smart Fan control system, support Thermal® and Speed® cruise for two onboard Fan

control connectors: FAN_CPU and FEATURE

•Three thermal inputs: CPU die temperature, System temperature and External

temperature input routed to FEATURE connector. (Precision +/- 3ºC)

•Voltage monitoring

•Intrusion detect input

•SMI violations (BIOS) on HW monitor not supported. Supported by API (Windows).

Operating

Systems

Support

•WinXP Professional

•Windows Vista

•Windows 7 *

•WinXP Embedded *

•Linux: Fedora Core 9 *, Fedora Core 10 *, Moblin *, Suse 11.1 *, Ubunty Jaunty (alpha

version) *

* = Limitations may apply (not all functions, drivers and features are tested).

(Continues)

KTD-00774-D KTUS15/mITX Page 12 of 82

www.kontron.com

Environmental

Conditions

Operating:

0°C – 60°C operating temperature (forced cooling). It is the customer’s responsibility

to provide sufficient airflow around each of the components to keep them within

allowed temperature range.

10% - 90% relative humidity (non-condensing)

Storage:

-20°C – 70°C

5% - 95% relative humidity (non-condensing)

Electro Static Discharge (ESD) / Radiated Emissions (EMI):

All Peripheral interfaces intended for connection to external equipment are ESD/ EMI

protected.

EN 61000-4-2:2000 ESD Immunity

EN55022:1998 class B Generic Emission Standard.

Safety:

UL/IEC 60950-1 2nd edition - 2007-03-27.

CSA C22.2 No. 60950-1-03 2nd edition - 2007-03-01.

IEC 60950-1:2005+A1

Product Category: Information Technology Equipment Including Electrical Business

Equipment

Product Category CCN: NWGQ2, NWGQ8

File number: E194252

Theoretical MTBF:

353.685 hours @ 40ºC, 170.050 hours @ 60ºC.

Restriction of Hazardeous Substances (RoHS):

All boards in the KTUS15 board family are RoHS compliant.

Capacitor utilization:

No Tantalum capacitors onboard

Only Japanese brand Aluminum capacitors rated for 100º Celsius used onboard

Battery

Exchangeable 3.0V Lithium battery for onboard Real Time Clock and CMOS RAM.

Manufacturer Panasonic / PN CR2032NL/LE, CR-2032L/BN or CR-2032L/BE.

Expected minimum 5 years retention varies depending on temperature, actual

application on/off rate and variation within chipset and other components.

Approximately current draw is 3-4 µA (no PSU connected).

CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

KTD-00774-D KTUS15/mITX Page 13 of 82

www.kontron.com

3.2 System overview

The block diagram below shows the architecture and main components of the KTUS15 family boards.

Components shown shaded are optional depending on variants of the board.

KTD-00774-D KTUS15/mITX Page 14 of 82

www.kontron.com

3.3 KTUS15/mITX Board configurations

Function

P/N 810290

KTUS15/mITX

1.6GHz Std

P/N 810291

KTUS15/mITX

1.1GHz Basic

P/N 810292

KTUS15/mITX

1.6GHz Plus

P/N 810293

KTUS15/mITX

1.1GHz Std

Processor Z530, 1.6GHz Z510, 1.1GHz Z530, 1.6GHz Z510, 1.1GHz

FSB speed 533MHz 400MHz 533MHz 400MHz

Memory, DDR2 SODIMM Up to 2GB Up to 2GB Up to 2GB Up to 2GB

Video output

CRT (DVI-A) Yes No No Yes

DVI (DVI-D) No Yes Yes No

LVDS Yes Yes Yes Yes

LAN Yes Yes Yes Yes

HD Audio Yes Yes Yes Yes

SATA port Yes, 2 ports No Yes, 2 ports Yes, 2 ports

PATA port Yes, 1 port Yes, 1 port Yes, 1 port Yes, 1 port

Compact Flash slot Yes Yes Yes Yes

SDIO slot Yes, 2 slots Yes, 2 slots Yes, 2 slots Yes, 2 slots

USB port Yes, 8 ports Yes, 8 ports Yes, 8 ports Yes, 8 ports

Serial port Yes, 2 ports Yes, 2 ports Yes, 4 ports Yes, 4 ports

Parallel / Printer port Yes, 1 port Yes, 1 port Yes, 1 port Yes, 1 port

Mse / Kbd interface Yes Yes Yes Yes

Feature connector Yes Yes Yes Yes

Frontpanel connector Yes Yes Yes Yes

FAN CPU connector Yes Yes Yes Yes

PCI slot Yes, 1 slot No Yes, 1 slot Yes, 1 slot

PCI express slot Yes, 2 PCIe x1

slots

Yes, 2 PCIe x1

slots

Yes, 2 PCIe x1

slots

Yes, 2 PCIe x1

slots

TPM chip onboard No No Yes No

KTD-00774-D KTUS15/mITX Page 15 of 82

www.kontron.com

3.4 System Memory support

The KTUS15 boards have one 200-pin DDR2 Small Outline Dual Inline Memory Module (SO-DIMM) socket.

The socket can be populated with up to 2GB of unbuffered DDR2 SO-DIMM modules.

Memory speeds up to 533MT/s (PC-4200) are supported.

•Supports 1.8-V DDR2 SDRAM with gold-plated contacts

•SDRAM Organisation of x16 supported only, up to 2 ranks, 8 loads only

•Supports 400 MT/s and 533 MT/s data rates

•Single 64-bit wide single-channel

•Support system memory from 512MB and up to 2GB

•Device density support for 512Mb and 1024Mb devices

•ECC not supported

•Serial Presence Detect required

The installed DDR2 SDRAM should support the Serial Presence Detect (SPD) data structure. This allows the

BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the

BIOS will attempt to configure the memory settings, but performance and reliability may be impacted.

Memory Operating Frequencies

The KTUS15/mITX maintains a fixed relationship between DRAM to FSB clock frequency. The FSB

frequency can be 400MHz or 533MHz, resulting in support of the following clock frequencies and data rates

for the DRAM.

CPU FSB Speed DRAM Clock DRAM Data Rate DRAM Type Peak Bandwidth

Z510, 1.1GHz 400MHz 200MHz 400MT/s DDR2 3.2GB/s

Z530, 1.6GHz 533MHz 266MHz 533MT/s DDR2 4.2GB/s

Note: Kontron offers the following memory modules:

4. P/N 825551, DDR2, 512MB, 200p, 667MZ, PC5300, SODIMM

5. P/N 825552, DDR2, 1GB, 200p, 667MZ, PC5300, SODIMM

6. P/N 825553, DDR2, 2GB, 200p, 667MZ, PC5300, SODIMM

KTD-00774-D KTUS15/mITX Page 16 of 82

www.kontron.com

3.5 KTUS15 Graphics Subsystem

The KTUS15 boards use the Intel ® US15W chipset for graphical control by the embedded Intel® Graphics

Media Accelerator 500.

The Intel Graphics Media Adapter includes LVDS and Serial DVO display ports permitting simultaneous

independent operation of two displays.

If external graphics is used (PCI) instead of the internal graphics device, LVDS and SDVO ports will not

function.

The KTUS15 board supports a Low-Voltage Differential Signaling interface that allows the Intel Graphics

Media Adapter to communicate directly to an on-board flat-panel display. The LVDS interface supports pixel

color depths of 18 and 24 bits, one-pixel per clock displays.

The Intel ® US15W chipset Serial DVO port either connects to a Serial DVO Digital DVI (DVI-D) or a

Serial DVO Analogue DVI (DVI-A) controller depending on the board configuration (refer to KTUS15/mITX

Board configurations section).

3.5.1 Intel® Graphics Media Accelerator 500

Features of the Intel® Graphics Media Accelerator 500.graphics controller includes:

•Integrated graphics (2D and 3D) and high-definition video decode capabilities with minimal power

consumption

o200MHz core frequency

oUMA memory architecture.

oMax video memory: 256MB. (Dynamic Video Memory). (Max. 8MB can be reserved in BIOS).

•3D Core Key Features

oDirect3D version 10.1 and OpenGL 2.0 compliant (TBD)

oTwo pipe scalable unified shader implementation.

3D Peak Performance

Fill Rate: 2 Pixels per clock

Vertex Rate: One Triangle 15 clocks (Transform Only)

Vertex / Triangle Ratio average = 1 vtx/tri, peak 0.5 vtx/tri

oTexture max size = 2048 x 2048

oProgrammable 4x multi-sampling anti-aliasing (MSAA)

oRotated grid

oOptimized memory efficiency using multi-level cache architecture

•Video

oFull hardware acceleration of video decode standards, such as H.264, MPEG2, MPEG4, VC1,

and WMV9.

oMPEG2 hardware acceleration: VLD + iDCT + MC

oVC-1 hardware acceleration: VLD + iMDCT + MC + LDF

•Display

oAnalog Display CRT output (DVI-A) (depending on configuration) with support for analogue

monitors up to 1600x1200 at 60Hz.

oDigital Visual Interface digital output (DVI-D) (depending on configuration) with support for digital

monitors up to 1600x1200 at 60Hz.

oSingle channel 18/ 24bit LVDS panel support (OpenLDI/ SPWG) up to Wide XGA (1366x768 at

85Hz) panel resolution. With external 1-to-2 pixel per clock converter, LVDS panels up to

1280x1024 are supported.

oDual independent pipe support, Mirror and Dual independent display support.

KTD-00774-D KTUS15/mITX Page 17 of 82

www.kontron.com

3.5.2 Dual Independent/Mirror/Single Display support

The table below shows the supported display configurations for the KTUS15 boards.

DID = Dual Independent or Mirror Displays

SD = Single Display

LVDS Interface

Mem. Freq. 533MT/s

Color depth 32bit

Refresh rate 60Hz

No Display

640x480

800x480

800x600

1024x600

1024x768

1280x768

1366x768

1280x1024

No Display N/A DID DID DID DID SD SD SD SD

640x480 DID DID DID DID DID

800x480 DID DID DID DID DID

800x600 DID DID DID DID DID

1024x600 SD

1024x768 SD

1280x768 SD

1366x768 SD

1280x1024 SD

1600x1200 SD

sDVO interface

1600x1200 SD

KTD-00774-D KTUS15/mITX Page 18 of 82

www.kontron.com

3.6 KTUS15 Power

3.6.1 Power Budget

The KTUS15 has several outlets for supplying power to external devices. Each power rail is independent of

other power rails, and the power budget for a single power rail can be shared among the interfaces that

utilize it. The maximum load for each rail should however not be exceeded, hence it is not possible to apply

full load to all external interfaces at the same time. The total power budgets for the individual rails are listed

below. Power output pins for the interfaces can be found in chapter 4.

Power available +12V +5V +3V3

Total maximum 2A 5A 6.7A

LVDS outlet 2A 1.5A 1A

PCI outlet 0.5A 5A 6.67A

PCIe outlet 0.5A - 3A

USB outlet - 4A -

3.6.2 Power Consumption

The KTUS15/mITX board is powered through the PWR connector by a single supply DC voltage.

Supply Min Max Note

+VIN 4.75V 26.2V Same as 5 – 25V +/-5%

KTUS15/mITX 1.1GHz normal operation:

KTUS15/mITX 1.6GHz normal operation:

KTUS15/mITX power down mode:

KTUS15/mITX external load additional power consumption:

Notes:

The onboard PSU efficiency varies depending on actual load, input voltage and temperature.

The above mentioned power consumptions are typical values and varies ~+/- 25% from system to system.

Windows XP Idle, No external load (C6 enabled)