Kontron KTQM67/mITX User manual

If it’s embedded, it’s Kontron
KTQM67 Users Guide
KTD-N0819-K
KTQM67/mITX
KTQM67/Flex
KTQM67/ATXP

KTQM67 Users Guide
KTD-N0819-K Page 2
Document revision history.
Revision
Date
By
Comment
K Jan 21st 2015 MLA
Correction “ETH3 Configuration (Lower)”. Correction of Mic2 and
Line2 location. mSATA description improved. EXT_BAT max.
3.47. Correct i5 3610ME data.
J
Dec 27th 2013
MLA
Correction to the Chipset > NB PCIe Configuration Menu.
I Dec 23rd 2013 MLA
CPU list revised. BIOS part upgraded in according to BIOS
Revision Release note (KTQM6715.bin)
H Jun 13th 2013 MLA
Major revision. Updated CPU list. Updated Memory list. Updated
BIOS part. Added much info and many corrections.
G July 10th 2012 MLA
Added USB port/EHCI relation. Added normal beep info. Added
info about backside label. Ivy Bridge support added. Note for
support of PCIe x2.
D-F
-
MLA
Comments removed in revision I.
A -C
-
MLA
Comments removed in revision G.
0
Jun 8th 2011
MLA
Preliminary version
Copyright Notice:
Copyright 2011, KONTRON Technology A/S, ALL RIGHTS RESERVED.
No part of this document may be reproduced or transmitted in any form or by any means, electronically
or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
Trademark Acknowledgement:
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer:
KONTRON Technology A/S reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve design
and/or performance.
Specifications listed in this manual are subject to change without notice. KONTRON Technology
assumes no responsibility or liability for the use of the described product(s), conveys no license or title
under any patent, copyright, or mask work rights to these products, and makes no representations or
warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration purposes only.
KONTRON Technology A/S makes no representation or warranty that such application will be suitable
for the specified use without further testing or modification.
Life Support Policy
KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL
MANAGER OF KONTRON Technology A/S.
As used herein:
Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with
instructions for use provided in the labelling, can be reasonably expected to result in significant injury to
the user.
A critical component is any component of a life support device or system whose failure to perform can
be reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.
Document details

KTQM67 Users Guide
KTD-N0819-K Page 3
KONTRON Technology Technical Support and
Services
If you have questions about installing or using your KONTRON Technology Product, check this User’s
Manual first – you will find answers to most questions here. To obtain support, please contact your local
Distributor or Field Application Engineer (FAE).
Before Contacting Support: Please be prepared to provide as much information as possible:
•CPU Board
1. Type.
2. Part Number (find PN on label)
3. Serial Number if available (find SN on label)
•Configuration
1. CPU Type, Clock speed
2. DRAM Type and Size.
3. BIOS Revision (Find the Version Info in the BIOS Setup).
4. BIOS Settings different than Default Settings (Refer to the BIOS Setup Section).
•System
1. O/S Make and Version.
2. Driver Version numbers (Graphics, Network, and Audio).
3. Attached Hardware: Harddisks, CD-rom, LCD Panels etc.
Warranty
KONTRON Technology warrants its products to be free from defects in material and workmanship
during the warranty period. If a product proves to be defective in material or workmanship during the
warranty period, KONTRON Technology will, at its sole option, repair or replace the product with a
similar product.
Replacement Product or parts may include remanufactured or refurbished parts or components.
The warranty does not cover:
1. Damage, deterioration or malfunction resulting from:
A. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
B. Repair or attempted repair by anyone not authorized by KONTRON Technology.
C. Causes external to the product, such as electric power fluctuations or failure.
D. Normal wear and tear.
E. Any other causes which does not relate to a product defect.
2. Removal, installation, and set-up service charges.
Exclusion of damages:
KONTRON TECHNOLOGY LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT
OF THE PRODUCT. KONTRON TECHNOLOGY SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Document details

KTQM67 Users Guide
KTD-N0819-K Page 4
Contents
Contents
Introduction .............................................................................................7
1Installation procedure........................................................................8
1.1 Installing the board ..........................................................................................................................8
1.2 Requirement according to IEC60950 ...................................................................................................9
2System Specification ........................................................................10
2.1 Component main data .....................................................................................................................10
2.2 System overview .............................................................................................................................14
2.3 Processor Support Table ..................................................................................................................16
2.4 System Memory support...................................................................................................................19
2.5KTQM67 Graphics Subsystem ............................................................................................................20
2.5.1 Intel HD Graphics 4000 ..................................................................................................................20
2.5.2 Intel® HD Graphics 3000................................................................................................................20
2.5.3 LVDS and DVI ................................................................................................................................21
2.5.4 Graphics Adapters .........................................................................................................................21
2.6 Power Consumption ........................................................................................................................22
3Connector Locations .........................................................................30
3.1 KTQM67/mITX – frontside ................................................................................................................30
3.2 KTQM67/mITX – IO Bracket area ....................................................................................................31
3.3 KTQM67/mITX - backside .................................................................................................................31
3.4 KTQM67/Flex..................................................................................................................................32
3.5 KTQM67/Flex - backside...................................................................................................................33
3.6 KTQM67/ATXP.................................................................................................................................34
3.7 KTQM67/ATXP - backside .................................................................................................................35
4Connector Definitions.......................................................................36
5IO-Area Connectors...........................................................................37
5.1 Display connectors (IO Area)............................................................................................................37
5.1.1 DVI Connector (DVI-I) (J41) ...........................................................................................................37
5.1.2 DP Connectors (DP0/DP1) (J40/J39) ...............................................................................................38
5.2 Ethernet Connectors .......................................................................................................................39
5.3 USB Connectors (IO Area) ................................................................................................................40
5.3.1 USB Connector 0/1 (USB0/1) .........................................................................................................40
5.3.2 USB Connector 2/3 (USB2/3) .........................................................................................................41
5.3.3 USB Connector 4/5 (USB4/5) .........................................................................................................41
5.4 Audio Connector (IO Area) ...............................................................................................................42
6Internal Connectors..........................................................................43
6.1 Power Connector (ATX/BTXPWR) .......................................................................................................43
6.2 Fan Connectors (FAN_CPU) (J28) and (FAN_SYS) (J29).......................................................................44

KTQM67 Users Guide
KTD-N0819-K Page 5
6.3 PS/2 Keyboard and Mouse connector (KBDMSE) (J27).........................................................................45
6.4 Display connectors (Internal)...........................................................................................................46
6.4.1 eDP connector (EDP) (J38) .............................................................................................................46
6.4.2 LVDS Flat Panel Connector (LVDS) (J20)...........................................................................................47
6.5 SATA (Serial ATA) Disk interface (J21 – J26) ......................................................................................48
6.6 USB Connectors (USB).....................................................................................................................50
6.6.1 USB Connector 6/7 ........................................................................................................................50
6.6.2 USB Connector 8/9 (USB8/9) (J10).................................................................................................50
6.6.3 USB Connector 10/11 (USB10/11) (J11)..........................................................................................51
6.6.4 USB Connector 12/13 (USB12/13) (J12)..........................................................................................51
6.7 Firewire/IEEE1394 connectors (J13,J14)...........................................................................................52
6.7.1 IEEE1394 connector (IEEE1394_0) (J14) .........................................................................................52
6.7.2 IEEE1394 connector (IEEE1394_1) (J13) .........................................................................................52
6.8 Serial COM1 – COM4 Ports (J15, J16, J17, J18)...................................................................................53
6.9 LPT (Line Print Terminal – Parallel port) (J44)....................................................................................54
6.10 Audio Connectors............................................................................................................................55
6.10.1 CDROM Audio Input (CDROM) (J3) ...................................................................................................55
6.10.2 Line2 and Mic2..............................................................................................................................55
6.10.3 Audio Header Connector (AUDIO_HEAD) (J31) .................................................................................56
6.11 Front Panel Connector (FRONTPNL) (J19) ..........................................................................................57
6.12 Feature Connector (FEATURE) (J30) ..................................................................................................58
6.13 “Load Default BIOS Settings” Jumper (J37) .......................................................................................61
6.14 SPI Recover Jumper (J4)..................................................................................................................62
6.15 SPI Connector (SPI) (J5)..................................................................................................................63
6.16 XDP-CPU (Debug Port for CPU) (J32) .................................................................................................64
6.17 XDP-PCH (Debug Port for Chipset) (J33) ............................................................................................65
7Slot Connectors (PCIe, miniPCIe, PCI) ................................................66
7.1 PCIe Connectors..............................................................................................................................66
7.1.1 PCI-Express x16 Connector (PCIe x16)..............................................................................................66
7.1.2 miniPCI-Express mPCIe0 (J34) ........................................................................................................68
7.1.3 miniPCI-Express mPCIe1 (J35) ........................................................................................................69
7.1.4 PCI-Express x1 Connector (PCIe x1) (J36) ........................................................................................70
7.2 PCI Slot Connectors ........................................................................................................................71
7.2.1 Signal Description – PCI Slot Connector ...........................................................................................72
7.2.2 KTQM67 PCI IRQ & INT routing.........................................................................................................73
8On-board - & mating connector types .................................................74
9System Resources.............................................................................75
9.1 Memory Map...................................................................................................................................75
9.2 PCI Devices ....................................................................................................................................76
9.3 Interrupt Usage ..............................................................................................................................77
9.4 IO Map...........................................................................................................................................78
10 BIOS................................................................................................80
10.1 Main..............................................................................................................................................80
10.2 Advanced.......................................................................................................................................81
10.2.1 Advanced -PCI Subsystem Settings ................................................................................................82
10.2.2 Advanced -APCI Settings ..............................................................................................................85
10.2.3 Advanced -Trusted Computing ......................................................................................................86
10.2.4 Advanced -CPU Configuration .......................................................................................................87

KTQM67 Users Guide
KTD-N0819-K Page 6
10.2.5 Advanced -SATA Configuration......................................................................................................89
10.2.6 Advanced -Intel TXT (LT) Configuration..........................................................................................93
10.2.7 Advanced -AMT Configuration .......................................................................................................94
10.2.8 Advanced -Acoustic Management Configuration .............................................................................96
10.2.9 Advanced -USB Configuration.......................................................................................................97
10.2.10 Advanced -SMART Settings ...........................................................................................................98
10.2.11 Advanced -Super IO Configuration.................................................................................................99
10.2.12 Advanced -Voltage Monitor ........................................................................................................105
10.2.13 Advanced -Hardware Health Configuration...................................................................................106
10.2.14 Advanced -Displayblock Setup ....................................................................................................108
10.2.15 Advanced -LAN Configuration .....................................................................................................109
10.2.16 Advanced -Delay Startup............................................................................................................111
10.2.17 Advanced -Serial Port Console Redirection ...................................................................................112
10.2.18 Advanced -CPU PPM Configuration...............................................................................................116
10.3 Chipset ........................................................................................................................................118
10.3.1 PCH-IO Configuration...................................................................................................................119
10.3.2 System Agent (SA) Configuration ..................................................................................................124
10.4 Boot............................................................................................................................................138
10.4.1 Force Boot Setup .........................................................................................................................140
10.4.2 CSM parameters...........................................................................................................................141
10.5 Security .......................................................................................................................................142
10.5.1 Image Execution Policy ................................................................................................................143
10.5.2 Key Management .........................................................................................................................144
10.5.3 HDD Security Configuration ..........................................................................................................145
10.6 Save & Exit...................................................................................................................................146
11 AMI BIOS Beep Codes ......................................................................147
12 OS Setup........................................................................................148

KTQM67 Users Guide
KTD-N0819-K Page 7
Introduction
This manual describes the KTQM67/mITX, KTQM67/Flex and KTQM67/ATXP boards made by
KONTRON Technology A/S. The boards will also be denoted KTQM67 family if no differentiation is
required.
The KTQM67 boards, all based on the QM67 chipset, support 2nd and 3rd generation Intel® i7 -, i5 -, i3
2Core and 4Core processor and the Celeron B810 2Core, see “Processor Support Table for more
specific details.
The KTQM67 family consist on members having different form factors, and the same functionality
except for the functions listed in the table below.
KTQM67 variants
Format
PCI
LPT
SODIMM Sockets
Single +12V Power Supply
KTQM67/mITX mITX -
-
2 Yes
KTQM67/Flex Flex 3
1
4 No
KTQM67/ATXP ATX 6
1
4 No
Use of this Users Guide implies a basic knowledge of PC-AT hard- and software. This manual is
focused on describing the KTQM67 board’s special features and is not intended to be a standard PC-AT
textbook.
New users are recommended to study the short installation procedure stated in the following chapter
before switching-on the power.
All configuration and setup of the CPU board is either done automatically or manually by the user via
the CMOS setup menus. Only exception is the “Load Default BIOS Settings” Jumper.
Introduction

KTQM67 Users Guide
KTD-N0819-K Page 8
Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the
PSU) or leave the Power Connectors unconnected while configuring the board. Otherwise
components (RAM, LAN cards etc.) might get damaged. If not using KTQM67/mITX and single
12V power input make sure PSU has 3.3V monitoring watchdog (standard ATX PSU feature),
running the board without 3.3V will damage the board within minutes.
!
!
Warning: When mounting the board to chassis etc. please notice that the board contains
components on both sides of the PCB which can easily be damaged if board is handled
without reasonable care. A damaged component can result in malfunction or no function at all.
1 Installation procedure
1.1 Installing the board
To get the board running, follow these steps. If the board shipped from KONTRON has already
components like RAM, CPU and cooler mounted, then relevant steps below, can be skipped.
1. Turn off the PSU (Power Supply Unit)
2. Insert the DDR3 DIMM 204pin SODIMM module(s)
Be careful to push it in the slot(s) before locking the tabs. For a list of approved DDR3 SODIMMs
contact your Distributor or FAE. See also chapter “System Memory Support”.
3. Install the processor
The CPU is keyed and will only mount in the CPU socket in one way. Use suitable screwdriver to
open/ close the CPU socket. Refer to supported processor overview for details.
4. Cooler Installation
Use heat paste or adhesive pads between CPU and cooler and connect the Fan electrically to the
FAN_CPU connector.
5. Connecting Interfaces
Insert all external cables for hard disk, keyboard etc. A monitor must be connected in order to be
able change CMOS settings.
6. Connect and turn on PSU
Connect PSU to the board by the ATX/BTXPWR and the 4-pin ATX+12V connectors. For the
KTQM67/mITX alternatively use only the 4-pin ATX+12V connector if single voltage operation (+12V
+/-5%) is requested.
7. Power Button
Depending on BIOS setting, the PWRBTN_IN must be toggled to start the Power supply; this is done
by shorting pins 16 (PWRBTN_IN) and pin 18 (GND) on the FRONTPNL connector (see Connector
description). A “normally open” switch can be connected via the FRONTPNL connector.
8. BIOS Setup
Enter the BIOS setup by pressing the <Del> key during boot up.
Enter Exit Menu and Load Optimal Defaults.
Refer to the “BIOS Configuration / Setup“ section of this manual for details on BIOS setup.
9. Mounting the board to chassis
When fixing the Motherboard on a chassis it is recommended using screws with integrated washer and
having diameter of ~7mm.
Note: Do not use washers with teeth, as they can damage the PCB and may cause short circuits.
Installation procedure
Note: To clear all BIOS settings, including Password protection, activate “Load Default BIOS Settings”
Jumper for ~10 sec (without power connected).

KTQM67 Users Guide
KTD-N0819-K Page 9
1.2 Requirement according to IEC60950
Users of KTQM67 family boards should take care when designing chassis interface connectors in order
to fulfil the IEC60950 standard:
Lithium Battery precautions:
CAUTION!
Danger of explosion if battery is incorrectly
replaced.
Replace only with same or equivalent type
recommended by manufacturer.
Dispose of used batteries according
to the manufacturer’s instructions.
VORSICHT!
Explosionsgefahr bei unsachgemäßem
Austausch der Batterie.
Ersatz nur durch den selben oder einen vom
Hersteller empfohlenen gleichwertigen Typ.
Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
ADVARSEL!
Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende
type anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til
fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laltevalmistajan
suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden
mukaisesti.
When an interface/connector has a VCC (or other power) pin, which is directly connected to a power
plane like the VCC plane:
To protect the external power lines of the peripheral devices, the customer has to take care about:
•That the wires have suitable rating to withstand the maximum available power.
•That the enclosure of the peripheral device fulfils the fire protecting requirements of IEC60950.
Installation procedure

KTQM67 Users Guide
KTD-N0819-K Page 10
2 System Specification
2.1 Component main data
The table below summarizes the features of the KTQM67/mITX, KTQM67/Flex and KTQM67/ATXP
embedded motherboards.
Form factor
KTQM67/mITX: miniITX (170,18 mm by 170,18 mm)
KTQM67/Flex: Flex-ATX (190,5 mm by 228,6 mm)
KTQM67/ATXP: ATX (190,5 mm by 304,0 mm)
Processor
Support 2nd and 3rd Generation Intel® Core™ (Sandy Bridge M and Ivy Bridge M
respectively) and Intel® Celeron® processors via Socket G2 (rPGA 988B ) ZIF Socket
•Intel® Core™ i7
•Intel® Core™ i5
•Intel® Core™ i3
•Intel® Celeron® B810
Up to 1333MHz system bus and 2/3/4/6MB internal cache.
Memory
•DDR3 SODIMM 204pin socket (2 sockets on mITX and 4 sockets on Flex/ATXP)
•Support single and dual ranks DDR3 1066/1333/1600MT/s
(PC3-8500/PC3-10600/PC3-12800)
•Support system memory from 256MB and up to 4x 8GB (2x 8GB on mITX).
Notes: Only some of the processors support 4 SODIMM slots.
Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•ECC not supported (PGA processors do not support ECC)
Chipset
Intel QM67 PCH (Platform Controller Hub)
•Intel ® VT-d (Virtualisation Technology for Directed I/O)
•Intel ® TXT (Trusted Execution Technology)
•Intel ® vPRO
•Intel ® AMT (Active Management Technology) version 8.0
•Intel ® AT (Anti-Theft Technology)
•Intel ® HD Audio Technology
•Intel ® RST (Rapid Storage Technology)
•Intel ® RRT (Rapid Recover Technology)
•SATA (Serial ATA) 6Gb/s and 3Gb/s.
•USB revision 2.0
•PCI Express revision 2.0
•ACPI 3.0b compliant
•Dual Display support (Dual Graphic Pipes)
•Blue-ray HD video playback
Security
•Intel® Integrated TPM 1.2 support
Management
•Intel® Active Management Technology (Intel® AMT) 8.0
Audio
Audio, 7.1 Channel High Definition Audio Codec using the VIA 1708B codec
•Line-out
•Line-in
•Surround output: SIDE, LFE, CEN, BACK and FRONT
•Microphone: MIC1 and MIC2
•CDROM in
•SPDIF (electrical Interface only)
•On-board speaker (Electromagnetic Sound Generator like Hycom HY-05LF)
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 11
Video
Intel i3, i5 & i7 3rd Generation Mobile processors support Intel HD Graphics 4000.
(Note that triple independent pipes are not supported on QM67 chipset)
Intel i3, i5 & i7 2nd Generation Mobile processor supports Intel HD Graphics 3000.
Intel Celeron Processor B810 supports Intel HD Graphics.
eDP (Embedded DisplayPort) directly from processor.
Analogue VGA and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel ®
QM67 Chipset.
•VGA (analogue panel) via DVI-I (sharing DVI-I connector with DVI-D)
•DVI-D (sharing DVI-I connector with analogue VGA)
•DP (DisplayPorts) dual, comply with DisplayPort 1.1a specification.
•LVDS panel support up to 24 bit, 2 pixels/clock and 1920x1200.
•HDMI panel support via DP to HDMI Adapter Converter.
•Second VGA panel support via DP to VGA Adapter Converter
•Second DVI panel support via DP to DVI Adapter Converter
•Dual independent pipes for Mirror and Dual independent display support
(exception is combination LVDS and eDP)
I/O Control
Via ITE IT8516E Embedded Controller and Nuvoton W83627DHG I/O Controller (both
via LPC Bus interface)
Peripheral
interfaces
•Six USB 2.0 ports on I/O area
•Eight USB 2.0 ports on internal pinrows
•Two IEEE 1394a-2000 (up to 400M bits/s) on internal pinrows
•Four Serial ports (RS232) on internal pinrows
•LPT via single in line connector (only KTQM67/Flex and KTQM67/ATXP)
•Two Serial ATA-600 IDE interfaces
•Four Serial ATA-300 IDE interfaces
•RAID 0/1/5/10 support
•mSATA via mPCIe_0 connector
•PS/2 keyboard and mouse ports via pinrow
LAN
Support
•1x 10/100/1000Mbits/s LAN (ETHER1) using Intel® Lewisville 82579LM Gigabit
PHY connected to QM67 supporting AMT 8.0
•2x 10/100/1000Mbits/s LAN (ETHER2/ETHER3)using Intel® Hartwell 82574L PCI
Express controllers
•PXE Netboot supported.
•Wake On LAN (WOL) supported
Expansion
Capabilities
•PCI Bus routed to PCI slot(s) (PCI Local Bus Specification Revision 3.0, 33MHz)
oKTQM67/mITX: None.
oKTQM67/Flex: 3
oKTQM67/ATXP: 6
•PCI-Express slot(s):
o1 slot PCIex16 (PCIe 2.0) ( also PCIe 2.0 when using Ivy Bridge CPU)
o1 slot PCIex1 (PCIe 2.0),
o1 slot miniPCI-Express (PCI Express or mSATA signals, no USB signals)
o1 slot miniPCI-Express (PCI Express signals, no mSATA or USB signals)
•SMBus, compatible with ACCES BUS and I2C BUS, (via Feature connector)
•SPI bus routed to SPI connector
•DDC Bus routed to DVI-I connector
•18 x GPIOs (General Purpose I/Os), (via Feature connector)
•DAC, ADC, PWM and TIMER (Multiplexed), (via Feature connector)
•WAKE UP / Interrupt Inputs (Multiplexed), (via Feature connector)
•3 Wire Bus for GPIO Expansion (up to 152 GPIOs), (via Feature connector)
•8 bit Timer output, (via Feature connector)
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 12
Hardware
Monitor
Subsystem
•Smart Fan control system, support Thermal® and Speed® cruise for two on-board
Fan connectors: CPU Fan (on-board) and System Fan (on-board)
•Smart Fan control system, support Speed® cruise for two off-board Fans
(Fan3/Fan4) via Feature Connector.
•Three thermal inputs: CPU Die temperature (precision +/- 3ºC), System
temperature (precision +/- 3ºC) and System Temperature External via Feature
Connector (precision +/- 1ºC).
•Voltage monitoring
•Intrusion (Case Open) detect input, (via Feature connector)
•Sleep S5# Indication, (via Feature connector)
•System Powergood Signal, (via Feature connector)
Power
Supply Unit
ATX/BTX (w. ATX+12V) PSU for full PCI/PCIe load.
Alternatively (mITX version only): +12V single supply via ATX+12V (4-pole) connector,
but with limitation to power load (especially +5V for USB).
Battery
Exchangeable 3.0V Lithium battery for on-board Real Time Clock and CMOS RAM.
Manufacturer Panasonic / Part-number CR-2032L/BN, CR2032N/BN or CR-2032L/BE.
Approximate 6.2 years retention.
Current draw is 4.1µA when PSU is disconnected and 0 µA in S0 – S5.
CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
BIOS
•Kontron Technology / AMI BIOS (EFI core version)
•Support for ACPI 3.0 ( Advanced Configuration and Power Interface), Plug & Play
oSuspend (S1 mode)
oSuspend To Ram (S3 mode)
oSuspend To Disk (S4 mode)
•“Always On” BIOS power setting
•RAID Support (RAID modes 0,1, 5 and 10)
Operating
Systems
Support
•WinXP (32b + 64b *)
•Vista (32b * + 64b *)
•Windows 7 (32b + 64b *)
•Linux
•VxWorks
•Windows Server 2003 r2 (32b * + 64b *)
•Windows Server 2008 r2 (32b * + 64b *)
•WES7 (32b + 64b)
*= Out Of The Box installation test only.
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 13
Environmental
Conditions Operating:
0°C – 60°C operating temperature (forced cooling). It is the customer’s
responsibility to provide sufficient airflow around each of the components to keep
them within allowed temperature range.
10% - 90% relative humidity (non-condensing)
Storage:
-20°C – 70°C; lower limit of storage temperature is defined by specification
restriction of on-board CR2032 battery. Board with battery has been verified for
storage temperature down to -40°C by Kontron.
5% - 95% relative humidity (non-condensing)
Electro Static Discharge (ESD) / Radiated Emissions (EMI):
All Peripheral interfaces intended for connection to external equipment are ESD/
EMI protected.
EN 61000-4-2:2000 ESD Immunity
EN55022:1998 class B Generic Emission Standard.
Safety:
IEC 60950-1: 2005, 2nd Edition
UL 60950-1
CSA C22.2 No. 60950-1
Product Category: Information Technology Equipment Including Electrical
Business Equipment
Product Category CCN: NWGQ2, NWGQ8
File number: E194252
Theoretical MTBF:
268.956 / 131.729 hours @ 40ºC / 60ºC for the KTQM67/mITX
253.955 / 122.738 hours @ 40ºC / 60ºC for the KTQM67/Flex
236.956 / 113.462 hours @ 40ºC / 60ºC for the KTQM67/ATXP
Restriction of Hazardous Substances (RoHS):
All boards in the KTQM67 family are RoHS compliant.
Capacitor utilization:
No Tantalum capacitors on board
Only Japanese brand Solid capacitors rated for 100 ºC used on board
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 14
2.2 System overview
The block diagram below shows the architecture and main components of the KTQM67. The key
component on the board is the Intel®QM67 (Cougar Point) Mobile Express Chipset.
Some components (PCI slots) are optional depending on board type.
More detailed block diagram on next page.
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 15
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 16
2.3 Processor Support Table
KTQM67 is designed to support the following PGA 988 processors (up to 60W power consumption):
2nd & 3rd generation Intel® Core™ i7 processor
2nd & 3rd generation Intel® Core™ i5 processor
2nd & 3rd generation Intel® Core™ i3 processor
Intel® Celeron® processor
In the following list you will find all CPU’s supported by the chipset in according to Intel but also other
CPU’s if successfully tested.
Embedded CPU’s are indicated by green text, successfully tested CPU’s are indicated by highlighted
text, successfully tested embedded CPU’s are indicated by green and highlighted text and failed
CPU’s are indicated by red text.
Some processors in the list are distributed from Kontron, those CPU’s are marked by an * (asterisk).
However please notice that this marking is only guide line and maybe not fully updated.
Processor
Brand
Clock Speed Turbo Speed Cores Threads Bus Speed Cache CPU Number sSpec number Stepping Thermal Design Power
SODIMM Qty
GHz GHz MHz MB ºC/W
Core™ i7
3.0
3.7
2
4
1333/1600
4
3540M
SR0X6
L1
105/35
4
3rd gen.
2.9
3.6
2
4
1333/1600
4
3520M
SR0MU
L1
105/35
4
2.8
3.8
4
8
1333/1600
8
3840QM
SR0UT
E1
105/45
4
2.7
3.7
4
8
1333/1600
8
3820QM
SR0MK
E1
105/45
4
2.7
3.7
4
8
1333/1600
6
3740QM
SR0UV
E1
105/45
4
2.6
3.6
4
8
1333/1600
6
3720QM
SR0ML
E1
105/45
4
2.4
3.4
4
6
1333/1600
6
3630QM
SR0UX
E1
105/45
4
2.3
3.3
4
8
1333/1600
6
3610QM
SR0MN
E1
105/45
4
2.3
3.3
4
8
1333/1600
6
3610QE*
SR0NP
E1
105/45
4
2.2
3.2
4
8
1333/1600
6
3632QM
SR0V0
E1
105/35
4
2.1
3.1
4
8
1333/1600
6
3612QM
SR0MQ
E1
105/35
4
Core™ i7
2.8
3.5
2
4
1066/1333
4
2640M
SR03R
J1
100/35
2
2nd gen.
2.7
3.4
2
4
1066/1333
4
2620M
SR03F
J1
100/35
2
2.5
3.6
4
8
1066/1333/1600
8
2860QM
SR02X
D2
100/45
4
2.5
3.5
4
8
1066/1333/1600
8
2920XM
SR02E
D2
100/55
4
2.4
3.5
4
8
1066/1333/1600
6
2760QM
SR02W
D2
100/45
4
2.3
3.4
4
8
1066/1333/1600
8
2820QM
SR012
D2
100/45
4
2.2
3.1
4
8
1066/1333
6
2670QM
SR02N
D2
100/45
4
2.2
3.4
4
8
1066/1333/1600
6
2720QM
SR014
D2
100/45
4
2.1
3.0
4
8
1066/1333/1600
6
2710QE*
SR02T
D2
100/45
4
2.0
2.9
4
8
1066/1333
6
2630QM
SR02Y
D2
100/45
2
Core™ i5
2.9
3.6
2
4
1333/1600
3
3380M
SR0X7
L1
105/35
4
3rd gen.
2.8
3.5
2
4
1333/1600
3
3360M
SR0MV
L1
105/35
4
2.7
3.4
2
4
1333/1600
3
3340M
SR0XA
L1
105/35
4
2.7
3.3
2
4
1333/1600
3
3610ME*
SR0QJ
L1
105/35
2
2.6
3.3
2
4
1333/1600
3
3320M
SR0MX
L1
105/35
4
2.6
3.2
2
4
1333/1600
3
3230M
SR0WY
L1
105/35
4
2.5
3.1
2
4
1333/1600
3
3210M
SR0MZ
L1
105/35
4
Core™ i5
2.6
3.3
2
4
1066/1333
3
2540M
SR044
J1
100/35
2
2nd gen.
2.5
3.2
2
4
1066/1333
3
2520M
SR048
J1
100/35
2
2.5
3.1
2
4
1066/1333
3
2510E*
SR02U
D2
100/35
2
2.3
2.9
2
4
1066/1333
3
2410M
SR04B
J1
100/35
2
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 17
Notes:
Using Ivy Bridge CPU increase Graphical performance (Intel ® HD Graphics 4000), and maybe also
increase CPU performance. PCIe x1, PCIe x2, PCIe x4, PCIe x8 and PCIe x16 are supported on the
PCIe x16 slot, however PCIe x2 is only supported when using 3rd generation Intel® Core™ processor
(Ivy Bridge). Using Ivy Bridge CPU do not implement support for 3 simultaneous displays, do not
implement support for USB 3.0 and do not implement support for PCIe 3.0. If any of these features are
required, then maybe KTQM77/mITX might be a solution.
When using Ivy Bridge CPU, make sure BIOS version is 10 or above.
Sufficient cooling must be applied to the CPU in order to remove the effect as listed in above table
(Thermal Guideline). The sufficient cooling is also depending on the maximum (worst-case) ambient
operating temperature and the actual load of processor.
The Kontron PN 1044-9447 is “Active Cooler for KTQM67/KTQM77”
capable of being used for processors (fully loaded) having Thermal
Guideline up to 45W @ 60ºC ambient temperature. MTBF is 70.000
hours @ 40ºC.
The Kontron PN 1052-6345 “Cooler Active KTQM67 35W 33mm
longlife” is capable of being used for processors (fully loaded) having
Thermal Guideline up to 35W @ 60ºC ambient temperature. It
support 1U and has long life (MTBF is 200.000 hours @ 60ºC).
All the processors in the list above, inclusive the Celeron processor, are supporting the Enhanced Intel®
SpeedStep® which is improved SpeedStep technology for faster transition between voltage (power
saving states) and frequency states with the result of improved power/performance balance.
Intel® Turbo Boost Technology 2.0 is supported by i5 and i7, as indicated in above list of processors,
and is enabling overclocking of all cores, when operated within the limits of thermal design power,
temperature and current.
Intel® vPro Technology is supported by some i5 and i7 (not by Core i3 and Celeron).
PCIex2 is only supported on the PCIex16 slot if using 3rd Generation Core2 CPU’s (Ivy Bridge).
Processor
Brand
Clock Speed Turbo Speed Cores Threads Bus Speed Cache CPU Number sSpec number Stepping Thermal Design Power
SODIMM Qty
GHz GHz
MHz MB
ºC/W
Core™ i3
2.6
-
2
4
1333/1600
3
3130M
SR0XC
L1
90/35
4
3rd gen.
2.5
-
2
4
1333/1600
3
3120M
SR0TX
L1
90/35
4
2.4
-
2
4
1333/1600
3
3120ME*
SR0QM
L1
105/35
2
2.4
-
2
4
1333/1600
3
3110M
SR0N2
L1
105/35
4
Core™ i3
2.4
-
2
4
1066/1333
3
2370M
SR0DP
J1
85/35
2
2nd gen.
2.3
-
2
4
1066/1333
3
2350M
SR0DN
J1
85/35
2
2.2
-
2
4
1066/1333
3
2330E*
SR02V
D2
100/35
2
2.2
-
2
4
1066/1333
3
2330M
SR04J
J1
85/35
2
2.2
-
2
4
1066/1333
3
2328M
SR0TC
J1
85/35
2
2.1
-
2
4
1066/1333
3
2312M
SR09S
J1
85/35
2
2.1
-
2
4
1066/1333
3
2310M
SR04R
J1
100/35
2
Celeron®
1.6
-
2
2
1066/1333
2
B810*
SR088
Q0
100/35
2
1.6
-
1
1
1066/1333
1.5
B710
100/35
2
System Specification
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 18
Intel AMT (Active Management Technology) is a part of vPRO and is hardware and firmware technology
that builds certain functionality into business PCs in order to remotely monitor, maintain, update,
upgrade, and repair PCs. Intel AMT relies on a hardware-based out-of-band (OOB) communication
channel that operates below the OS level, the channel is independent of the state of the OS (present,
missing, corrupted, down). The communication channel is also independent of the PC's power state
(however standby power required), the presence of a management agent, and the state of many
hardware components (such as hard disk drives and memory). AMT is not intended to be used by itself;
it is intended to be used with a software management application based on 3rd party software. If AMT is
not required then KTHM65/KTHM76 might be an alternative or AMT can be disabled in BIOS. For more
information search for “AMT” on Intel Homepage.
A few types of 2nd Generation Core 2 processors and the Celeron processor only support two SODIMM
and not all four SODIMM sockets available on the KTQM67/Flex and - /ATXP. In the table above the
“Qty. of SODIMM slots” indicates if actual processor supports 2 or 4 SODIMM slots.
Slot 1
Slot 0
KTQM67/mITX has two DDR3 SODIMM slots and
any of the two slots can be used.
Intel ® AMT works as long as RAM is installed in
any of the slots.
KTQM67/Flex and KTQM67/ATXP versions have
four DDR3 SODIMM slots. Only some processors
support all four slots, if not one of these CPU’s then
only Slot 0 and Slot 2 can be used.
Intel ® AMT works as long as RAM is installed in
either Slot 0 and/or Slot 2
Slot 3
Slot 2
Slot 1
Slot 0
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 19
2.4 System Memory support
The KTQM67/mITX has two DDR3 SODIMM sockets and the KTQM67/FLEX and /ATXP have four
DDR3 SODIMM sockets. The sockets support the following memory features:
•1.5V (only) 204-pin DDR3 SODIMM with gold-plated contacts
•Single/dual rank unbuffered DDR3 1066/1333/1600MT/s (PC3-8500/PC3-10600/PC3-12800)
(DDR3 1600 only supported by some i7 processors)
•From 256MB and up to 4x 8GB. (up to 2x4GB tested)
Notes:
Only some of the processors support 4 SODIMM slots
(see processor Support Table for more information).
Less than 4GB displayed in System Properties using 32bit OS
(Shared Video Memory/PCI resources is subtracted)
•SPD timings supported
•ECC not supported (PGA processors do not support ECC)
The installed DDR3 SODIMM should support the Serial Presence Detect (SPD) data structure. This
allows the BIOS to read and configure the memory controller for optimal performance. If non-SPD
memory is used, the BIOS will attempt to configure the memory settings, but performance and reliability
may be impacted.
Memory Operating Frequencies
Regardless of the SODIMM type used, the memory frequency will either be equal to or less than the
processor system bus frequency. For example, if DDR3 1600 memory is used with a 1333 MHz system
bus frequency processor, the memory clock will operate at 666 MHz. The table below lists the resulting
operating memory frequencies based on the combination of SODIMMs and processors.
DIMM Type Module name Memory Data
transfers
Processor
system bus
frequency
Resulting memory
clock frequency Peak transfer rate
Mill/s
MHz
MHz
MB/s
DDR3 1066
PC3-8500
1066
1066 or more
533
8533
DDR3 1333
PC3-10600
1333
1333 or more
666
10666
DDR3 1600
PC3-12800
1600
1333 max
666
10666
DDR3 1600
PC3-12800
1600
1600
800
12800
Notes: Kontron offers the following DDR3 204P SODIMM:
PN 1054-37731GB, 1066MHZ, PC3-8500
PN 1054-37801GB, 1333MHZ, PC3-10600
PN 1054-37761GB, 1600MHZ, PC3-12800
PN 1054-37772GB, 1066MHZ, PC3-8500
PN 1054-37812GB, 1333MHZ, PC3-10600
PN 1051-54032GB, 1600MHZ, PC3-12800
PN 1054-37784GB, 1066MHZ, PC3-8500
PN 1054-37824GB, 1333MHZ, PC3-10600
PN 1051-90574GB, 1600MHZ, PC3-12800
PN 1054-37838GB, 1333MHZ, PC3-10600
PN 1054-37758GB, 1600MHZ, PC3-12800
System Specification

KTQM67 Users Guide
KTD-N0819-K Page 20
2.5 KTQM67 Graphics Subsystem
The KTQM67 equipped with Intel 2nd Gen i3, i5 or i7 processor, supports Intel HD Graphics 3000,
equipped with 3rd Gen i3, i5 or i7 processor the Intel ® HD Graphics 4000 is supported (however only up
to two graphical pipes) and equipped with Intel Celeron Processor B810 the Intel HD Graphics is
supported.
All KTQM67 versions support eDP (Embedded DisplayPort) directly from processor, and analogue VGA
and digital display ports (DVI, 2x DP, LVDS) via the Mobile Intel ® QM67 Chipset. The Analogue VGA
and DVI-D are sharing the DVI-I connector.
The DP interface supports the DisplayPort 1.1a specification. The PCH supports High-bandwidth Digital
Content Protection for high definition content playback over digital interfaces. The PCH also integrates
audio codecs for audio support over DP interfaces.
Up to two displays (any two display outputs except combination LVDS and eDP) can be activated at the
same time and be used to implement dual independent display support or mirror display support. PCIe
and PCI (Flex/ATXP only) graphics cards can be used to replace on-board graphics or in combination
with on-board graphics.
2.5.1 Intel HD Graphics 4000
Features of the Intel HD Graphics 4000 build into the i3, i5 and i7 processors, includes:
•High quality graphics engine supporting
oDirectX11 and OpenGL 4.0 compliant
oShader Model 5.0 support
oIntel ® Clear Video HD Technology
oIntel ® Quick Sync Video Technology
oIntel ® Flexible Display Interface (Intel ® FDI)
oCore frequency of 650 - 1150 (Turbo) MHz
oMemory Bandwidth up to 21.3 GB/s
o16 3D Execution Units
o1.62 GP/s and 2.7 GP/S pixel rate (eDP and DP outputs)
oHardware Acceleration CVT HD and QSV
oDynamic Video Memory Technology (DVMT) support up to 1720 MB
•DP0 and DP1
o24/30 bit colours in WQXGA (2560x1600 pixels) and HDCP.
oDisplayPort standard 1.2
2.5.2 Intel® HD Graphics 3000
Features of the Intel HD Graphics 3000 build into the i3, i5 and i7 processors, includes:
•High quality graphics engine supporting
oDirectX10.1 and OpenGL 3.0 compliant
oShader Model 4.1 support
oIntel ® Clear Video HD Technology
oIntel ® Quick Sync Video Technology
oIntel ® Flexible Display Interface (Intel ® FDI)
oCore frequency of 350 - 1300 (Turbo) MHz
oMemory Bandwidth up to 21.3 GB/s
o12 3D Execution Units
o1.62 GP/s and 2.7 GP/S pixel rate (eDP and DP outputs)
oHardware Acceleration full MPEG2, full VC-1 and full AVC
oDynamic Video Memory Technology (DVMT) support up to 1720 MB
•eDP (Embedded DisplayPort) (Not in combination with LVDS)
•DP0 and DP1
o24/30 bit colours in WQXGA (2560x1600 pixels) and HDCP.
oDisplayPort standard 1.1a
System Specification